HOME CONTROL CHIME Doors CHIME Special Motion THE PROTECTOR ELITE EMERGENCY OWNER’S MANUAL ® LIGHTS Time Activated LIGHTS Sensor Activated THE PROTECTOR 1
FCC Notices FCC Part 15 Information to the User Changes or modifications not expressly approved by Interactive Technologies, Inc. can void the user’s authority to operate the equipment. FCC Part 15 Class B This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against interference in a residential installation.
TABLE OF CONTENTS Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Security System Beeps, Lights, and Messages . . . . . 5 How to Use Your Control Panel . . . . . . . . . . . . . . . . . . . 8 How to Use Your Touchpads . . . . . . . . . . . . . . . . . . . . 10 Programming Your System . . . . . . . . . . . . . . . . . . . . . 11 System Tests & Trouble Beeps . . . . . . . . . . . . . . . . . . .14 Your Emergency Evacuation Floor Plan . . . . . . . . . . . .
Introduction to Your System KeyChain Touchpads Your security system uses wireless technology to warn your family about intrusion and fire. It may also be used to control lights and appliances within your home. KeyChain Touchpads are used to control the security system from within or near the outside of your home. The system is designed to be monitored and/or to send messages to a numeric pager.
Security System Beeps, Lights, and Messages Your security system communicates to you through the use of panel voice messages, panel beeps, indicator lights on the panel itself, and to a numeric pager if programmed. You communicate to your security system with key presses on the Control Panel, touchpads, or through the use of a remote telephone. Disarming and programming require you to input a 4-digit access code. The Master Access Code default is 1-2-34 when the security system is shipped from the factory.
Alarm Sirens and Lights Exterior and interior sirens make 3 different alarm sounds on the premises, each indicating a different type of alarm. Sirens will time-out and stop sounding after the siren timeout (programmable by the installer). System controlled lights also indicate the type of alarm. Use the following table to understand alarm sounds and controlled lights.
How to Use Your Control Panel The Control Panel interface consists of 3 columns of buttons. They are: HOME SECURITY, CODE, and HOME CONTROL. There is a non-medical EMERGENCY button located on the far right. HOME SECURITY SYSTEM STATUS. Press twice to hear information ARM Doors & Windows. Press once to turn the security system protection on for all protected doors and windows. If a door or window is open when you arm the system, it will be bypassed, meaning not protected.
HOME CONTROL EMERGENCY If any of the HOME CONTROL buttons are pressed and a sensor or module is not associated (programmed) with this feature the Control Panel will say, Function not available. Press EMERGENCY for 2 seconds or twice quickly to call the central monitoring station and notify them of a non-medical call for help. CHIME Doors. Press to cause the Control Panel to beep when protected doors or windows are opened.
How to Use Your Touchpads Touchpads are used to control the security system from any location within or near your home. Remote Handheld Touchpad SYSTEM STATUS Press once to hear information about your system. See “System Tests & Trouble Beeps” on page 14. SYSTEM STATUS ARM Doors & Windows ARM Doors & Windows Press once to turn the security system protection on for all protected doors and windows. Press twice to eliminate the preprogrammed entry delay.
Programming Your System What You Can Change: Options: Press Add in the START MENU and follow the voice prompts to turn an option on. Press Delete in the START MENU to turn an option off. Option 01 - Panel Beeps Panel Beeps are any beeps (including chime beeps) that come from the Control Panel. Panel Beeps, except for alarm sirens, may be disabled. See “Panel Beeps” on page 5. Option 02 - Panel Voice Panel Voice may be disabled, except for status messages, open sensor responses, and when in program mode.
Programming Using Panel Decal The programming decal is visible when you open the Control Panel cover. The decal is designed to make system programming easier for you. Always begin by choosing a button from the START MENU. Follow the voice prompts and flow arrows to complete the desired task. Notice the button flow diagrams under Instruction Summary to the right of the buttons. 8988G37D.
Step by Step Programming Instructions Use the following instructions to access the programming buttons and programming decals. Open the Control Panel Cover by pressing the plastic latch on the top of the Control Panel. When you open the cover you will immediately be prompted by the Control Panel voice to use the red numbered keys to enter your ID. 2. Enter Your Access Code. 7. Close the Control Panel cover. 1. The Master access code is 1-2-3-4 when the panel is shipped.
System Tests & Trouble Beeps Automatic Control Panel Testing--What the System Tests for You Your security system is able to automatically test itself for: • • • • Power failures Low batteries Non-working sensors Communication troubles with the Central Monitoring Station Trouble Beeps. When your security system detects one of the problems above, interior sirens sound trouble beeps rapidly six times, and then again every minute, until the trouble condition is corrected.
Manual Tests--What You Need to Test As an added safeguard, there are system tests you should do yourself on a regular basis. The Control Panel cover in the lower left corner reminds you to TEST WEEKLY. Sensors You can test sensors one at a time to make sure they are sending strong signals to the Control Panel (see Testing Sensors paragraph). Communication You can also test the communication between your system and the Central Monitoring Station (see Testing Communication paragraph).
Your Emergency Evacuation Floor Plan Planning for Emergencies This section describes what you can do to plan ahead for an emergency: • • Emergency Planning Your Floor Plan Emergency Planning Since an emergency is always unexpected, you should develop plans to help prepare for a variety of emergency situations.
Alarm System Limitations Not even the most advanced alarm system can guarantee protection against burglary, fire, or environmental problems. All alarm systems are subject to possible compromise or failure-to-warn for a variety of reasons. • • • • • • • If sirens are not placed within hearing range of persons sleeping or in remote parts of the premises, or if they are placed behind doors or other obstacles.
$ / AC Power Failure 10, 13 AC Power Restoral 10 Access Code, change 12 Access Code, delete 12 Access Codes 10 Alarm 6 Alarm Sirens and Lights 6 Alarm System Limitations 16 Alarm Type 6 Alarms 10 ARM Doors/Windows 5, 7, 9 ARM Doors/Windows & Motion Sensors 5 ARM Motion Sensors 5, 7, 9 Arm with Doors or Windows Open 3 Arming 10 Latchkey 7, 10 limitations 16 LOCK 9 % Option 01 - Panel Beeps 10 Option 02 - Panel Voice 10 Option 03 - Latchkey Time 10 Option 41 - Voice Chime 10 Option 43 - Pager Phone Numbe
7 Table Alarm Type 6 Table Numeric Pager 6 Table Options 12 Table Panel Beeps 5 Table Panel Indicator Lights 6 Table Sensor Tripping Instructions 14 test phone 14 Testing Communication 14 Testing Sensors 10, 14 touchpads 9 Trouble Beeps 5, 13 trouble beeps, silencing 13 Trouble Messages 13 8 UNLOCK 9 18
Quick Reference Table REMOTE HANDHELD & Touchtalk 2-Way RF TOUCHPAD KEYCHAIN TOUCHPAD REMOTE PHONE CONTROL Arm the system – Doors & Windows ARM Doors & Windows ARM Doors & Windows Press Arm the system – Motion Sensors ARM Motion Sensors ARM Motion Sensors Press Arm the system – Doors/Windows & Motion Sensors ARM Doors & Windows ARM Motion Sensors ARM Doors & Windows Activate No Entry Delay ARM Doors & Windows Press Twice ARM Doors & Windows Activate the Latchkey feature ARM Motion Sensor
