1. reduction Scapegoat TH / STCI000WIFI TH Is an Integrated plug-and-play temperature and humbly controller it has temperature and humidity integrated probe and is per-connected to two output sockets to control temperature and humidity simultaneously. The large LUD screen Intuitively displays temperature, humidity, and other parameters, With the three key design, it enables quick parameter setting, such as alarm limit, calibration, protection time, unit switching, etc.
1.2 Parameter Table {TER 78 TR THT Ta TAL TEA HEY HAH HAL HEA £1 *HEB: BEE: Flag SIN | Leda Function | Settles ran Ba tali val Temperature 1 | TCH | consolidating CH ¢ rode selection Tempest et n value 2 mae 5 i 0.215 Temperature i differential 1~ 30°F 3 3 Teleportation . 4 i i Eo FONT 35 5 | ray | Temperature slates high felt | 23.
23.3 Button Operation See a a ae eee 18H | Mason | von fling) FTE ops | View parterre] Rev Vow | eases 1 & Crass and Continents hold rn rn Erases fern nbn. Wadi 2 fy Proxy ang Pointers | Serine node | sen aerie mode sands pra | Vipers Na | : value pa press and Contuses fol] decries [| reprimand Ari 4 This | abe | a 5) ewe WaT ber | Een tf See Table 3 %, Operation important: improper use of the product may cause Injury or product marriage. Please read, understand and follow the operating steps below.
2.9 Sensor installation Plug the sensor fully Anti the headphone Jack from the button of the main frontier, Fully Plug In Fig. 4 3.2 Power-on Please Insert the power plug Into the power socket to prows on the controller within the range of 100-240VAC). The screen wil light up and display the tempera tuns, humidity, and other readings.
1.3 Parameter Setting Press and hal button for 3 seconds to enter the parameter setting mode, the buzzer will beep, and the LCD will display <4, Leon, Ir the ren setting, press button and the Te parameter light will be on or flashes. When it is flashing, press Litton to switch to the next parameter; when the parameter light is on, press button to increase or decrease the setting value.
Enter i SAT The LL ee Temperature mode selection Temperature set val FT Ea] Temperature ui Fig.7 ity mode selection ) Humidity set value Continuous working time Back light time & Enter reds and aid ESE ofr ees Tm =A.
4. Function Description 41 Temperatures Sorting TCH, TE, TD ng mode {TCH = 0} ‘When Trv (temperature-present value) is higher than TS + TD (temperature-set value + temperature differential), @ will appear, wri will be turned on, and cooling will begin; When Tey {temperature present wale} Is lowlier han TS temperature sat value, 8 will disappear, work will be muted off, and roofing will stop. For example: TS = 15°C, TD = 5°C, as shown in Fig 5.
4.
Humidifying Mods (10H « 1) ‘When Hev {humidity present value) is [wore than HS-HD (humidity set value torridity differential), 8 will appear, work? will be muted on, and Humidifying will begin; # WORK On When Hov {nudity present value) is %RH [] work of higher than HS (tumidity valueless, 8 ye co ‘will apes, work will be fumed off, and humidifying will stop. 40 For strapless: HS = SO%RH, HD = 10%RH, as shown in Fig 1. Fig. 11 4.
£98 Continues Operating Thur COT During humidity control, when C0T=0 and output conditions are met, WORK socket will work in on-off-on-off.. mode, COT is tee on as well as time off eg, IF COT=10, the LICORICE output socket will tum on For 10 minutes and off for “10 inures, then repeat. Wuhan COT = 0 ard output conditions are met, WORK autistic socket will not free affected by LOT. 4.78 Back light Tami the screen display Tums. When Bl=0 indicates display is always on. 5.
& Alarm n the following circumstances during operation, the buzzer will give a “hi bi-Biii* anal, and at the same tine, the alarm symbol fe on the screen will appear. Press any button to mute the alarm.
8.1 Before you begin, please make sure: The device supports 246 WI-Fi. {5G WI-Fi is nat compatible.) “The device is in a good and stable WI-Fi network environment. Search Fichte In the App Store, download and Install the app. $.2 Concetta the device te Blithe app 1. Fin the OR code label on the device {#t shows QR code and 20 numbers) 2. Peeper on The device. 3. Log In your Attache account {Register an Chattel account) 4, Click the sign + on top right and add device. combatant Fig. 14 5.
&.4 window will pop up "The device 1 scanned is 3 WEF device, Would vou Bike bs set WIFI lick OK. sn won Fig. 16 7 Enter WI-F| password, click OK, and Walt until the operation finishes, The whole process takes about 10 rear ery ‘seconds. It exits configuration Interface m— after the network Is connected fu shy successfully. EEE Thi rate terrace displays the device is online, Meanwhile, the sign shows on top of the screen. n Fig.
