Contents DISCRIMINATORY ovo i 4 Product Features Technical Parameters Service Parks oo 3 Operation Guide re era as raga er een, 4 Care and Maleficence «rem re rer g App Operating Instructions «rm 11
Disclaimer = Tha vacuum pump is heavy He careful while handling to prevent personal injury, * Use only 46 mechanical oli to avoid vacuum pump damage. » [ig not cover the exhaust sort during vacuum pep cooperation: = [in not expose the suction port continuously To lampshade for runs than 3 minutes: * The alr Inlet pressie should not exceed 97.5 ar 40 sold sensor damage.
service Paris 3) Handle (8) Motor housing Ballerina OB Peer burn £2) Semisolid valve 0) Vacuum sensor 5) Lather 42 ull window 6 antitank 4 Oil drain plug 3
{aeration Gulls Conditions that must be met 1. Place on a flat surface; 2. Confirm the voltage and frequency at the outlet match with tha vacuum pump specifications; 3. Confirm the oil level Is within the Min and Max level; 4, Turnover the air inlet cap (7/16 » -20 fitting as shown in the right image }, connect the pumped system (make sure the pipe fitting Is fit with the alr inlet fitting). Tighten the air inlet and make sure the system and hoses are sealed with no leakage; 5.
{1} The status bar on top of the page shows the product model, time, Bluetooth status and record status. (@ Model numbers varies depending on the product models. @ % Bluetooth not connect; %* Bluetooth connected. (@ During operation, E appear when temperature exceeds the upper alarm limit, and F appear when temperature below the lower alarm limit. @ Record: close means no data Is recorded. Record: Open means that data ls being recorded {2} The middies part of the page is the sub-interface button.
{1} Motor Status: show the current status of the motor {2) Motor Temp/Limit: show the surface temperature of the pump chassis and set the alarm temperature; {3} Oil temperature: show vacuum pump oll temperature and set the alarm temperature; {8} Vacuum status: display the current vacuum value status, "Decrease”, "Stabla®, "Marisa, "7; {5} Completion them: when the vacuum Is stable, It shows the estimated job completion them.
3. Settings Click the “Settings” button on the main menu to enter the setting interface Unit (BT) Select Unit to set the unit for vacuum and temperature. The selected units are in green. Vacuum Set the minimum vacuum value, logging interval, snd recording status, {1} Minimum vacuum: set the target vacuum value. The range of the minimum vacuum value Is Click the change button to switch the minimum vacuum value; the display unit changes according to the selected unit.
Time {1} Set and save the time then it shows at the top of the screen. {2} = : Change key; 3) [@ : return to the main interface 4, System in the main menu, click the * system” button to enter the system interface.
Other functions 1 Temperature alarm: When the oll temperature or miter chassis temperature exceeds the upper limit alarm temperature set by the APR the motor and solenoid valve are closed, the temperature lama icon" F * is displayed at the top of the screen; When the temperature decrease within the alarm temperature, the anal will be deader, and ‘the vacuum work continues | If temperature exceeds the offline lama temperature, the temperature alarm con® “will be displayed an the top of the vacuum pump screen
How to replace the vacuum pump oll 1. Run the pump for about 3-Minutes unt iris warmed up to runs out the pump olf; 2. Keep the air girder open and let the oil in the spurn flow out. Turn off the pump and remove the drain plug to discharge the waste ofl: 3, Sift the pump body to completely drain the residual ofl, and tighten the drain plug; 4. Open the catch device and add the new pump off; 5.
1. Too Much of OI Drain the oll to the oll level line. Pump Fuel Injection 2. The Alr inlet Is Over Pressured for | con 3 pump with larger pumping speed. along Time 1.0ll Temperature Is Tao Low Open the alr Inlet, start the motor repeatedly or heat up the pollute 2. Gator Allure Check and repair. Difficulty Starting 3. Foreign Objects Fallen Ina the Check and clean 4. Power Allure Check and repair. 5. The Power Supply Voltage Is Too Low Check the power supply voltage. APP Operating Instructions 1.
4. Click "Add device” to enter the device management Interface. And the devices that can be connected are displayed In red. Click 63] on the top fight of the device to establish a connection. After successful connection the device bar tums green and the Bluetooth icon displays I E. For the connected device, click at the bottom right of the device to add the device ‘to the work interface. The bottom of the screen shows that the device has been added successfully; &.
Screenshot Device name Real-tine vacuum vale Mat address Search to add anew device The interface includes historical devices and the new devices.
7. Chick” [8" in the top left comer of the working interface to enter the menu. {Only some functions related to vacuum spurn are described here} {1) Report (© Work: Click the work button to enter the work list. Add a work list at the top right. Add work information and save the work.
(@ Report: Click the report button to enter the report interface. Click the New report button, select data Information by work or time, click the chart analysis button to view historical graph, click the “Export” button af the bottom to export data in Excel or POF Click the saved report to view historical Excel and POF reports,and long press the report to delete. Pesto ns DRE Ewa pan ti ws HL CRIER, {3) Screen capture: save the screen capture file of the work interface.
{2} Configuration (@ Setting: Click the “Setting” button to enter the system settings; Stat Seaman Seton enn din Back light om: control the back light of the screen; Switch language: select language English or Chinese; Alarm mode setting: single sound, single vibration or sound vibration alarm at the same time; Logging Interval: Set the data login interval when generating the report, 15, 308, Min, 5 Min, 10 Min, 15 Min, 30 Min, 60 Min; (@ Help: Click the “Help” button to enter the help interface; click the
8. Main interface Click the connected devices loon to enter the detailed Interface of the device, display the vacuum pump status, and control the vacuum pump.
{7} Leakage level: Under the stable state of the vacuum value, make a judgment on the possibility of leakage of the current system, which Is represented by 0-100; © means the uncertain of the leakage status. The larger the number, the possibility of leakage is larger.
{2} Basic settings @ Device name: modify the device name, support up to 10 characters and numbers, click OK to save the device mama; @ Vacuum unit: select vacuum unit, in Hg, Terr, mar, motor, Pa, micron, kPa; @ Temperature unit: select the temperature unit, °C, °F; Holding time: the continue working time after reaching the target vacuum, the setting range is 0 to 200 minutes; {2} Alarm settings (© Vacuum alarm setting: when the vacuum reaches the alarm value, the mobile phone will alarm and vibrate; @ Temp