■ chapter 4 upgrading your computer C H A P T E R ▼ F O U R UPGRADING YOUR COMPUTER In this chapter, you will learn how to upgrade the DRAM, hard disk drive, and to install the optional wireless LAN mini PCI card.
■ chapter 4 upgrading your computer Upgrading the Hard Disk Drive Replacing the original drive with one of larger capacity can increase the hard drive capacity of your computer. The computer uses a 9.5 mm (height), 2.5-inch Ultra ATA-66 / 100 / 133 type hard disk. Be sure to make a backup copy of all your data before attempting this operation. Warning: Hard drive upgrade is a delicate process. Please observe the following instructions carefully or have a qualified technician install it for you.
■ chapter 4 upgrading your computer Upgrading the Hard Disk Drive To replace the hard disk drive, do the following: 1. Turn OFF the computer. Unhook the AC cord and all cables/devices attached to the notebook. 2. Place your hand on a large metal object momentarily to discharge any static electricity. 3. Locate and remove 11 Screw A’s on the Metal Cover. 4. 5. Remove the Metal Cover. Locate and remove 1 Screw B. Gently push the HDD module to the right to disengage from the HDD connector.
■ chapter 4 upgrading your computer 6. Locate and remove 4 Screw C’s from the HDD module. Remove the metal case. 7.
■ chapter 4 upgrading your computer tighten 4 Screw C’s. Note the green PC board of the hard disk drive is facing against the metal case. 8. Re-insert the HDD module to the HDD connector. 9. Re-attach and tighten 1 Screw B. (If the HDD assembly is not fully inserted into the bay, the screw and its hole will not line up.) 10. Replace the System Device Cover and 11 Screw A’s. Congratulations! You have now completed the hard drive upgrade.
■ chapter 4 upgrading your computer Upgrading the System Memory Many applications will generally run faster when the computer’s dynamic memory capacity is increased. The computer provides one DDR memory socket, located underneath the System Device Cover. You can increase the amount of memory by replacing the existing one with a dual inline memory module (commonly known as DIMM) of a higher capacity. The DIMM can be 128MB, 256MB, 512MB, or 1024MB in capacity.
■ chapter 4 upgrading your computer Installing a memory module (DIMM) into the system To install the DIMM, do the following: 1. Power OFF the notebook. Unplug the AC cord and all cables/devices attached to the notebook. 2. Place your hand on a large metal object momentarily to discharge any static electricity. Place the notebook on a flat surface and fully open the LCD lid. 3. Locate and remove 11 Screw A’s on the Metal Cover. 4. Remove the Metal Cover. The DIMM socket is now seen as shown below.
■ chapter 4 upgrading your computer Dual DDR DIMM Sockets 5. If you need to remove an old DIMM from the socket, press out on the latches located on both edges of the socket at the same time. The DIMM should pop up to an angle of 30 degree (see diagram below.). Pull the DIMM module out of the memory socket. Store away the DIMM for the future use. 6. Install the new DIMM module into the memory socket. The DIMM will only fit in one orientation.
■ chapter 4 upgrading your computer 7. Pivot the DIMM until the latches on both sides of the socket snap into place. Note: Notice the notch on the DIMM. The notches should fit nicely with the socket. 8. Replace the System Device Cover and 11 Screw A’s. Congratulations! You have just completed the memory upgrade. When you boot up the computer, you should expect to see an increase in DRAM capacity. Note: Your computer has been tested with a wide range of DIMM on the market.
■ chapter 4 upgrading your computer Adding a Mini-PCI Type Wireless LAN Card (Optional Device) Your computer comes with a unique Mini PCI Card socket, which is located next to the DRAM socket and inside the DRAM door. The socket allows the computer to add unique features such as wireless LAN (IEEE802.11b). Ask your dealer on the availability of the mini PCI card. Warning: Installing a mini PCI card is a delicate process.
■ chapter 4 upgrading your computer Installing a Mini PCI Card into the System To install a new Mini PCI card, do the following: 1. Follow steps in the previous section, Installing a memory module (DIMM) into the system, to access the Mini PCI Socket. Mini PCI Socket 2. The mini PCI card will only fit in one direction. Align the small notch in the module with the socket on the connector and insert the card at an angle of approximately 30 degrees into the empty socket.
■ chapter 4 upgrading your computer 3. Locate 2 antenna cables with connectors. Snap the cable onto the golden connector on the Mini PCI Wireless LAN card. (Note: The connectors are fairly small! This may take some maneuvering. You may want to connect the antenna cables before inserting the wireless card into the socket. ) 4. Replace the System Device Cover and 11 Screw A’s. Congratulations! You have now completed the mini PCI card installation.
