i
Preface Copyright 2010 All Rights Reserved. The information in this document is subject to change without prior notice in order to improve reliability, design and function and does not represent a commitment on the part of the manufacturer. In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use the product or documentation, even if advised of the possibility of such damages.
Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help This device complies with Part 15 of the FCC Rules.
Table of Content BEFORE YOU START ............................................................................... 2 LET YOUR COMPUTER ACCLIMATE ITSELF .............................................. 9 HEAT, COLD, HUMIDITY, AND GLARE .................................................... 9 SUITABLE PLACE TO WORK ................................................................. 10 INTRODUCTION...................................................................................... 12 FRONT VIEW ....................
NO SPEAKER OUTPUT ........................................................................ 54 SOUND CANNOT BE RECORDED .......................................................... 54 THE HARD DISK DRIVE DOES NOT WORK OR IS NOT RECOGNIZABLE ....... 55 THE HARD DRIVE IS MAKING ABNORMAL WHINING NOISES ..................... 55 THE HARD DISK DRIVE HAS REACHED ITS CAPACITY ............................. 55 THE HARD DISK TAKES LONGER TO READ A FILE ................................... 56 THE FILES ARE CORRUPTED ......
1
Before you Start Conventions of This Manual Use this manual will help you get the most from your notebook computer. If you are an experienced user of computers and/or Microsoft’s Windows operating systems, you might find it useful to read the Quick Start Guide that comes along with your accessories. If you are a less experienced user, you should through the manual carefully before using your system.
7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. Make sure to use the right voltage for the power source when connecting the equipment to the power outlet. Place the power cord in such a way that people can not step on it. Do not place anything on top of the power cord. All cautions and warnings on the equipment should be noted. If the equipment is not use for a long time, disconnect the equipment from the main power outlet to avoid being damaged by transient overvoltage.
The minimum specifications for the flexible cord are No. 18 AWG, (2) Type SPT-2, and (3) 2-conductor. B. For Japan: All components of the cord set must bear a “PSE” mark and in accordance with the Japanese Dentori Law. The minimum specifications for the flexible cord are .75m ㎡ conductors, (2) Type VCTR or VCTFK, and (3) 2-conductor. The cord set must have minimum rated current capacity of 7 A.
of electric shock from lightning. Do not use the telephone to report a gas leak in the vicinity of the leak. Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a fire. They may explode. Check with local codes for possible special instructions. 19. Do not use the AC adapter near open water or other liquids. Never spill liquid into the AC adapter. 20. Danger of explosion if battery is incorrectly replaced.
Class 1 Laser Product Appareil A Laser De Classe 1 Laserschutzklasse 1 Produkt Do not attempt to disassemble the cabinet containing the laser. The laser beam used in this product is harmful to the eyes. The use of optical instruments, such as magnifying lenses, with this product increase the potential hazard to your eyes. For your safety, have this equipment serviced only by an authorized service provider. Wichtige Sicherheitshinweise 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13.
14. 15. 16. 17. Stromnetz zu trennen und von einer qualifizierten Servicestelle zu Überprüfung.: a. Netzlabel oder Netzstecker sind beschädigt. b. Flüssigkeit ist in das Gerät eingedrungen. c. Das Gerät war Feuchtigkeit ausgesetzt. d. Wenn das Gerät nicht der Bedienungsanleitung entsprechend funktioniert oder Sie mit Hilfe dieser Anleitung keine Verbesserung erzielen. e. Das Gerät ist gefallen und/oder das Gehäuse ist beschädigt. f. Wenn das Gerät deutliche Anzeichen eines Defektes aufweist.
Die Minimalanforderungen für das Kabel sind .75m ㎡ Leiter. (2) Type VCTF oder VCTFK, und (3) 2conductor. Der Kabelsatz muss mindestens für eine Stromstärke von 7A geeignet sein. Der Wandstecker muss ein zweipoliger geerdeter Steckertyp gemäß dem Japanese Industrial Standard C8303 (15A, 125 VAC) sein. C. Für andere Länder: Die Zubehörteile des Kabel-Sets müssen das Prüfsiegel derjenigen Stelle, die in dem jeweiligen Land für die Sicherheitsprüfung zuständig ist, tragen.
angegebenen Stromkabel und Batterien. Werfen Sie die Batterien nicht ins Feuer, sie könnten explodieren. Informieren Sie sich über die örtlichen Bestimmungen bezüglich der Entsorgung. 19. Benutzen Sie das Netzteil nicht in unmittelbarer Nähe zu Wasser oder anderen Flüssigkeiten. Gießen Sie nie Flüssigkeiten über das Netzteil. 20. Es besteht Explosionsgefahr, wenn der Akku nicht ordnungsgemäß ersetzt wird.
Do not block the ventilation opening. Do not place your computer in direct sunlight. Suitable place to work Your computer will run well wherever you’re comfortable but extremes of temperature and humidity can be challenging to your system’s parts. There are some things you can tolerate that the computer can’t – things like static electricity, dust, water, steam and oil. In case you decide to pull over for roadside computing, try to choose a clean, comfortable work area for your system.
11
Introduction Please use the adapter recommended in this manual.
Turning on your computer Knowing your Computer With the LCD screen open, you will see several features important for operating your notebook computer. To avoid damage to the display panel: 1. Try not to slam the display upon closing it. 2. Try not to place any object on top when it is closed or open. 3. Be sure the system is turned off or in suspend mode before you close the display panel.
LCD Display This LCD panel can only support up to a maximum opening of 115-120 degrees, please do not push it forcibly. Power/Suspend Button Press for 1~1.5 seconds to turn on the system. Press and hold for at least 4 seconds to turn off the system. Press the power / suspend button again to return from the suspend mode.
4-in-1 Card Reader {SD(SDHC)/MMC/MS/MS Pro Memory Card} Touchpad Touchpad Buttons Left Views 15
Kensington Lock DC In Modem Port (Optional) Always disconnect all telephone lines from the wall outlet before servicing or disassembling this equipment. To reduce the risk of fire use only No. 26 AWG or larger telecommunication line cord. Ethernet / LAN Port When using a LAN, please use an EMI Shielding Cable to minimize an inteference when transmitting 16 USB 2.
Right View USB 2.0 Port Enhanced USB 2.
Bottom View Battery Release Latch Battery Compartment Battery Lock 18
19
Getting Started Connecting to a Power Source Connecting the AC Adapter A universal AC adapter is provided to supply your computer with power and also charge the computer’s battery pack. The adapter’s AC input voltage can range anywhere from 100 to 240 volts, covering the standard voltages available in almost every country. To connect the computer to an external power source: Do not use inferior extension cords as this may result in damage to your notebook. The notebook comes with its own AC adapter.
Whenever possible, keep the AC adapter plugged into the notebook and an electrical outlet to recharge the battery. Never turn off or reset your notebook while the hard disk is in use status icon is lit; doing so can result in loss or destruction of your data. Always wait at least 5 seconds after turning off your notebook before turning it back on; turning the power on and off in rapid succession can damage the notebook’s electrical circuitry.
Danger of explosion if battery is incorrectly replaced. Replace only with same or equivalent type recommended by the manufacturer. Discard used batteries according to the manufacturer’s instructions or local laws. Explisionsgefahr bei unsachgernazen Austausch der Batterie. Ersatz nur durch denselben oder einem vom Hersteller empfohlenem ahnlichen Typ. Entsorgung gebrauchter Batterien navh Angaben des Herstellers.
Charging the Battery Pack The installed battery pack charges automatically any time the computer is connected to the AC adapter and an external power source. It is a good idea to occasionally discharge the battery pack fully to preserve its operating performance.
24
Using the Notebook Computer Adjusting the LCD Screen Display The LCD screen display can be adjusted by the following key combinations. Fn + F4 Fn + F7 Fn + F8 Changes Display Mode: LCD-only, CRT-only and simultaneous LCD&CRT/HDMI. Decrease the brightness level. Increase the brightness level. LCD Care LCD screens are delicate devices that need careful handling. Please pay attention to the following precautions: When you are not using the computer, keep the LCD screen closed to protect it from dust.
You can switch between these display configurations by pressing the key combination [Fn] + [F4]. The Notebook’s Hot Key Controls Action Fn + Esc Fn + F1 Fn + F2 Fn + F3 Fn + F4 Fn + F5 Fn + F6 Fn + F7 Fn + F8 Fn + F9 Fn + F10 Fn + F11 Fn + F12 System Control Enable/Disable the Bluetooth (Optional) Enters Suspend Mode. Enters the Silent Mode. Mute/Unmute Audio/ PC beep to Output Changes Display Mode: LCD-only, CRT-only and simultaneous LCD&CRT/HDMI. Decrease the speaker volume. Increase the speaker volume.
TouchPad Precautions The TouchPad is a pressure sensitive device. Please take note of the following precautions. Make sure the TouchPad does not come into contact with dirt, liquids or grease. Do not touch the TouchPad if your fingers are dirty. Do not rest heavy objects on the TouchPad or the TouchPad buttons. You can use the TouchPad with Microsoft Windows as well as nonWindows applications.
If you use the battery so frequently that it exceed more than 20 times by fully discharging/charging in a single month alone, we recommend you to perform the “Battery Calibration” process every 3 months to maintain the battery life. Please refer to the topic on “Battery Calibration” describing how to calibrate your system battery discussed on the latter part of this chapter. If you discover the battery life is getting shorter, please perform the “Battery Calibration” process immediately.
Automatic Battery Pack Charging Function To charge the battery, while the battery pack is in the notebook, plug the AC adapter into the notebook and an electrical outlet. The charging time is approximately 3-4 hours when the notebook is turned off and approximately 6-7 hours when the notebook is turned on. When the battery is fully charged, the battery charge indicator becomes off. If system runs at heavy loading or in a high temperature environment, the battery may not be fully charged.
When there is only one minute of battery charge remaining, the notebook will suspend to the HDD and power off. You should connect AC power and resume to save your work. Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer's instructions. Never remove the battery pack while the power is on as this may result in data loss when the system loses power.
Using the Windows Help Windows For Windows 7 help, click Start Help and Support icon will open the dialog box. Desktop Desktop may vary differently on the software installed in your notebook with different or additional shortcuts.
Recycle Bin Used for storing deleted files in case you want to recover and save it in your system. The files will only be deleted from the Recycle Bin permanently only if you empty it by right clicking your mouse and select the “Empty Recycle Bin”. Start Button Allows easy access to all Windows programs.
The Start menu allows you to adapt and show the programs used most frequently. If you wish to keep an item, right click the item and click Pin to Start menu. Log Off will enable the current user to log off and allows a new user to log on. Turn Off Computer allows you to shut down, restart, and Stand by modes for power saving purposes. Taskbar When you open a program, its icon is displayed at the taskbar for you to conveniently move between programs by clicking the relevant button.
Control Panel It is in this area that you can change how Windows looks and works. Click Start Control Panel dialog box. There are two interfaces – Classic View.
35
Internet Connection Using a modem for Connection to Internet (optional) 36
For more detail on the Network key, please refer to your local ISP provider and follow the procedures describe in the “ISP Installation Guide” to proceed with the installation.
Using Wireless LAN Network for Connection to Internet 38
39
Running BIOS Setup The Setup Utility is a hardware configuration program built into your computer’s BIOS (Basic Input/Output System). It runs and maintains a variety of hardware functions. It is menu-driven software, which allows you to easily configure and change the settings. The BIOS contains manufacture’s default settings for the computer’s standard operations. However, there are occasions when you may be required to modify the default settings in the BIOS.
BIOS Action Keys Function Key ESC Enter F1 F9 F10 + Command Description Leaves a sub-menu to return to the Exit previous menu OR exits the BIOS setup while saving changes. Go to Sub Screen Shows the Sub Menu General Help Shows the Help Screen Default Set to default Saves changes and reboots the Save and Exit computer. Select a field Selects the next field. Select an item Selects the next upper item. Select an item Selects the next lower item.
Main Setup Under this menu, you may change time/date and view basic processor and system memory information.
Info Setup 43
Advanced Security 44
Boot Setup 45
Exit Setup 46
47
VGA Utilities You can click the touchpad or mouse right button and select the “Personalize” item.
Adjust Resolution 49
Calibrate Color Adjust Display Setting 50
Connect to a Projector Adjust Clear Type Text 51
52
Troubleshooting Your computer has been fully tested and complies with the system specifications before shipping. However, incorrect operations and/or mishandling may cause problems. This chapter provides a reference for identifying and correcting common hardware and software problems that you may encounter. When you encounter a problem, you should first try to go through the recommendations in this chapter.
Be sure all the device drivers are installed properly. For example, without the audio driver properly installed, the speakers and microphone will not work. If external devices such as USB camera, scanner, printer do not function correctly when connected to the system, it is usually the device’s own problem. Consult the device’s manufacturer first. Some software programs, which have not gone through rigorous coding and testing, may cause problems during your routine use.
Click Options and select Properties. Select Recording and click the OK button. After Click OK button, the recording volume control panel will appear. Go to [Start > Settings > Control Panel] and double-click the Multimedia icon (or Sounds and Audio Devices icon). In the Volume or Audio page, make sure that the audio codec mentioned in the spec is the default recording device.
Many browsers store files in the hard drive as a cache to speed up the performance. Check the program’s Online Help for instructions on decreasing the cache size or on removing temporary Internet files. Empty the Recycle Bin to create more disk space. When you delete files, Windows saves them to the Recycle Bin. The hard disk takes longer to read a file If you have been using the drive for a period, the files may be fragmented.
The screen flickers It is normal if the display flickers a few times during shutting down or powering up. Keyboard and Mouse Problems The built-in touch pad performs erratically Make sure there is no excess perspiration or humidity on your hand when using the touch pad. Keep the surface of the touch pad clean and dry. Do not rest your palm or wrist on the surface of the touchpad while typing or using the touch pad.
This battery normally lasts two to five years. The battery is of type CR2032 (3V). Send the battery to the dealer for replacement. Memory Problems The POST does not show an increased memory capacity when you have already installed additional memory Certain brands of memory module may not be compatible with your system. You should ask your vendor for a list of compatible DIMM. The memory module may be defective.
The card may be defective. Try the card on another system, if possible. Windows crashes or freezes when you remove the PC card Make sure you have the PC card before removing it. Double-click the Safely Remove Hardware icon at the lower right corner of the task bar and select the card you wish to stop. When you click , in few seconds Windows will prompt you to remove the card.
USB2.0 Problems The USB device does not work Check the settings in the Windows Control Panel. Make sure you have installed the necessary device drivers. Contact the device vendor for additional support. Unable to use the External USB Device Detach the external device; insert it into the Enhanced USB port. Separate the cable with the equipment; first insert the wire into the port, then connect the device with the cable that is inserted into the Enhanced USB port.
61
Specification O.S. Supports Windows 7 Home Premium CPU Intel® Pentium® Processor ULV CPU SU4100 Penryn 1.3GHz/800MHz/2M/10W Intel® Celeron® Processor ULV CPU SU2300 Penryn 1.2GHz/800MHz/1M/10W ULV CPU 743 Penryn 1.3 GHz/800MHz/1M/10W Memory DDR3 operating voltage is 1.5V, SO-DIMM*2 .Max.
Card reader (4 in 1) Support SD(SDHC)/MMC/MS/MS Pro Memory Card USB2.0 interface LAN Controller Supports 1000Mb/sec (10/100M compatible) Wireless LAN Half-Mini Card type IEEE 802.11 B/G/N (1x1) PCI-E Interface Camera CCD (Optional) Support 1.3M Camera Bluetooth (Optional) LiteOn solution WB111C-C1(Toshiba) AW-BT280 (Toshiba) BT 2.1 w/ EDR compliance hardware Modem (Optional) D40 AM5 MDC1.5 CASTLENET (12PIN) modem module ML3054-LV MDC1.
Battery Pack 4 cells, LG 14.4V 2200mAH (4S1P) CEL TYPE: C42-4S2200-C1L3 4 cells, ATL 14.6V 2200mAH (4S1P) GTC TYPE: C42-4S2200-M1A2 8 cells, LG 14.4V 4400mAH (4S2P) CEL TYPE: C42-4S4400-C1L3 8 cells, ATL 14.6V 4400mAH (4S2P) GTC TYPE: C42-4S4400-M1A2 AC-Adapter Automatics Voltage adjustment between 100 and 240VAC 50/60Hz, LV5 -19V / LV4-20V, 65 Watts. 2 Pin Delta Electronics, Inc. ADP-65HB AD (65W 2pin), ADP-65JH AB (65W 2pin), ADP-65JH BB (65W 3pin) Lite-On Technology Corporation.
EMI CE/FCC RF R&TTE, FCC Safety CB/CCC/ETL 65
