i
Preface ©Copyright 2007 All Rights Reserved. The information in this document is subject to change without prior notice in order to improve reliability, design and function and does not represent a commitment on the part of the manufacturer. In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use the product or documentation, even if advised of the possibility of such damages.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • • • Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technic
Table of Content ATTENTION: TEACHERS, PARENTS AND ADULT SUPERVISORS .................1 1. AGENCY REGULATORY NOTICES................................................3 MODIFICATIONS ...................................................................................4 CONNECTIONS TO PERIPHERAL DEVICES ..............................................4 EUROPEAN NOTICE .............................................................................4 CANADIAN NOTICE........................................................
4. BIOS SETUP AND SECURITY FEATURE.....................................25 ENTERING THE BIOS SETUP SCREEN ................................................25 BIOS ACTION KEYS ..........................................................................26 MAIN SETUP .....................................................................................27 ADVANCED SETUP .............................................................................28 SECURITY SETUP .....................................................
Attention: Teachers, Parents and Adult Supervisors Please ensure that students understand the following: • • • • • • • • • • Emphasize to student that this device is an educational tool and not a toy. The computer, power supply, battery pack or power cord should not be dropped, crushed, stepped on or otherwise abused. This product is intended for school age children, ages 6 and up. Ensure students understand the safe and proper handling of power cord and power supply.
2
1. AGENCY REGULATORY NOTICES Federal Communications Commission Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Modifications The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by the Manufacture may void the user’s authority to operate the equipment. Connections to Peripheral Devices Connections to this device must be made with shielded cables with metallic RFI/EMI connector hoods to maintain compliance with FCC Rules and Regulations. Declaration of Conformity This device complies with Part 15 the FCC Rules.
• • • EN 300 328-2, EN 300 328-1, EN 301 489-1, EN 301 489-17 (ETSI 300 328, ETSI 301 489) Electro-magnetic Compatibility and Radio Spectrum Matter. TBR21 (ETSI TBR21) Terminal Equipment. EN60950 (IEC60950) I.T.E. Product Safety Canadian Notice This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the radio interference regulations of the Canadian Department of Communications.
Users should ensure for their own protection that the electrical ground connections of the power utility, telephone lines and internal metallic water pipe system, if present, are connected together. This precaution may be particularly important in rural areas. Users should not attempt to make such connections themselves, but should contact the appropriate electric inspection authority, or electrician, as appropriate.
• The attachment plug must be a two-pole, grounded type with a Japanese Industrial Standard C8303 (15 A, 125 VAC) configuration. Other Countries • • • • The cord set fittings must bear the certification mark of the agency responsible for evaluation in a specific country.
Model: HP-OK065E03 (65W), HP-OK065E13 (65W) Battery Pack Safety • • • • • • • • • • • The battery pack is intended to use only with this notebook. The battery pack is not replaceable by the end user. Only qualified service technicians should replace the battery pack. Do not disassemble the pack. Do not dispose of the battery pack in fire or water. To avoid risk of fire, burns, or damage to your battery pack, do not allow a metal object to touch the battery contacts.
Lithium battery warning / Bridge battery warning This computer contains a lithium battery to power the clock and calendar circuitry. Danger of explosion if battery is replaced incorrectly. Replace only with the same or equivalent type recommended by the manufacturer. Discard used batteries according to the manufacturer’s instructions. Il y a danger d’xplosion s’il y a remplacement incorrect de la batterie. Remplacer uniquement avcc unc batterie du meme type ou d’un type recommande par le constructer.
10
2. GETTING TO KNOW THE BASICS System At A Glance Top View 1. 2. LCD Display The panel is where the system content is displayed. Power / Suspend Button The power/suspend button turns the notebook on and off and it also acts as a system suspend key. Press momentarily to turn on the system. Press and hold for at least four seconds to turn off the system.
Press the power/suspend button again to return from the suspend mode. (See Chapter 3 for more details on system suspend function.) 3. 4. 5. 6. 7. 12 LED When the system is in Suspend Mode, the status indicator shows green light. LED Status Indicator The LED Status indicators reveal the status of these functions: Numeric keypad, cap lock, WLAN module enabling and disabling and also the data activities. (See the LED Status Indicator Section for details.
Side Views Do not place any heavy objects on the top of notebook. This may damage the display. 1. 2. 3. 4. 5. Ethernet / LAN Port The port connects to a network hub via the RJ-45 cable and also conforms to 10/100Base-TX transmission protocol. USB2.0 Port (x2) The Universal Serial Bus (USB2.0-compliant) port allows you to connect a wide variety of devices to your computer at a rate of up to 480 Mbps. This port conforms to the latest USB2.0 plug-and-play standards.
6. 7. Power Jack (DC-in) The DC-out jack of the AC Adapter connects here and powers the computer. 2-in-1 Card Reader The 2-in-1 Card Reader supports SD Card and MMC Card. You need to remove the outer jacket to access the card reader slot on the rear side of the computer. Flip open the jacket and the card reader slot is seen.
1. 2. 3. DC-out Connector The DC-out connector docks to the power jack (DC-in) on the computer. Adapter The adapter converts alternating current into constant DC voltage for the computer. AC Plug The AC Plug plugs to the AC wall outlet. LED Status Indicator The LED Status Indicator displays the operating status of your notebook. When a certain function is enabled, an LED will light up. The following section describes the indication.
Keyboard Features Function Keys (Quick Keys) The function keys allow you to quickly access certain controls, such as screen brightness, audio volume, suspend mode, etc. Press and hold the Fn key and then press the various function key to activate the following controls. Graphic Symbol Action Fn + F1 Fn + F2 Fn + F4 Turns the WLAN module off or on. When the Wireless LAN function is enabled, the LED status indicator shows green light. Enables or Disables the Card Reader function. Enters the Suspend Mode.
Windows* Keys Your keyboard also has two Windows keys: 1. Start Key This key allows you to pull up the Windows Start Menu at the bottom of the taskbar. 2. Application Menu Key This key brings up the popup menu for the application, similar to a click of the right mouse button. Embedded Numeric Keypad Press Fn+Num Lk to enable the embedded numeric keypad. The numbers are printed in the upper right corner of a key, in a color different from the alphabets.
Access Context Menu Move One Page Up or Down Click once Tips on Using the Touch Pad: 1. 2. 3. The double-click speed is timed. If you double-click too slowly, your notebook responds as if you single-clicked twice. Keep your fingers dry and clean when using the touch pad. Also keep the surface of touch pad clean and dry to prolong its life. The touch pad is sensitive to finger movements. Hence, the lighter the touch, the better the response. Heavy touch does not produce better response.
To maximize your battery operating time, set the brightness to the lowest comfortable setting, so that the internal backlight uses less power. Extending the Life of the TFT Display Device Observe the following guidelines to maximize the life of the backlight in the display. 1. 2. 3. Set the brightness to the lowest comfortable setting (Fn+F5). Do not disable the suspend time-outs. If you are using AC power, change to suspend mode when not in use.
For example, you may use Microsoft Sound Recorder. Ethernet Your computer is equipped with a 10/100Base-TX Fast Ethernet network adapter. Connect the active LAN cable to the RJ-45 LAN port located on the left side of the computer. This allows you to access and transmit data in the local area network. Connecting to the Network Use Unshielded Twisted Pair (UTP) Ethernet cable only. 1. 2. Insert one end of the UTP cable into the network connector until the connector snaps securely into the receptacle.
3. BATTERY POWER & POWER MANAGEMENT In this chapter, you will learn how to operate your notebook on battery power and learn about the system’s power saving features. TFT display, central processor, hard disk drive (optional) are the major hardware subsystems that consume the most power. Power management deals how these key components should behave to conserve power. For example, you can have the system turn off its display after two minutes of inactivity to save power.
When the notebook warns you of its low battery condition, you will have about three to five minutes to save your current work. Do not expose battery packs to temperatures below 0 degree Celsius (32 degree F) or above 60 degree C (140 degree F). This may adversely affect the battery pack. Charging the Battery and Charging Time To charge the battery, plug the AC adapter into the notebook and an electrical outlet.
• • • The life expectancy of the battery is approximately 300 recharges. See the notices section in the beginning of the user manual on how to care for the battery pack. Use Function+F5 key to decrease the brightness of the screen. To achieve optimal battery performance, you may need to do a battery calibration at a 3-month interval. To do this: • • • Fully charge the battery. Then discharge the battery by entering the BIOS setup screen. (Press DEL key as soon as you turn on the computer.
However, depending on how much RAM that has been installed on your computer, the amount of time the system requires to restore all its previous contents can range from five to 20 seconds. Power Button Action A classmate PC’s power button can be set to turn off the system or activate the suspend mode.
4. BIOS SETUP AND SECURITY FEATURE The Setup Utility is a hardware configuration program built into your computer’s BIOS (Basic Input/Output System). It runs and maintains a variety of hardware functions. It is menu-driven software, which allows you to easily configure and change the settings. The BIOS contains manufacturer’s default settings for the computer’s standard operations. However, there are occasions when you may be required to modify the default settings in the BIOS.
BIOS Action Keys Function Key Command Description ESC Exit Leaves a sub-menu to return to the previous menu OR exits the BIOS setup while saving changes. Enter Go to Sub Screen Shows the Sub Menu. F1 General Help Shows the Help Screen . F9 Setup Defaults Load default values. F10 Save and Exit Saves changes and reboots the computer. Select a field Selects the next field. ↑ Select an item Selects the next upper item. ↓ Select an item Selects the next lower item.
Main Setup Under this menu, you may view BIOS Version and system memory capacity and also change system time and date. BIOS SETUP UTILITY Main Advanced Security BIOS Information BIOS Version: EC Version: Boot Exit Use [+] or [-] to configure system Time. x.xx x.
Advanced Setup Under this menu, you may view CPU information, configure HDD (optional), and enable/disable wireless LAN and LAN port. BIOS SETUP UTILITY Main Advanced Security Advance Settings WARNING: Setting wrong values in below sections may cause system to malfunction. ► CPU Configuration ► IDE Configuration ► Communication Boot Exit Configure CPU. ←→ Select Screen ↑↓ Select Item Enter Go to Sub Screen F1 General Help F10 Save and Exit ESC Exit (C) Copyright 1985-2004, American Megatrends, Inc.
Security Setup BIOS SETUP UTILITY Main Advanced Security Security Settings Supervisor Password: Not Installed User Password: Not Installed Change Supervisor Password Change User Password Boot Exit Install or change the password. ←→ Select Screen ↑↓ Select Item Enter Change F1 General Help F10 Save and Exit ESC Exit (C) Copyright 1985-2004, American Megatrends, Inc. • • Supervisor Password: Install or Change the Password. User Password: Install or Change the Password.
Boot Setup BIOS SETUP UTILITY Main Advanced Security Boot Settings ► Boot Settings Configuration ► Boot Device Priority ► Hard Disk Drives ► Removable Drives Boot Exit Install or change the password. ←→ Select Screen ↑↓ Select Item Enter Change F1 General Help F10 Save and Exit ESC Exit (C) Copyright 1985-2004, American Megatrends, Inc. • Boot Settings Configuration: See Below.
• Boot Device Priority: See Below. Item First Boot Device Second Boot Device Selections / Sub-menu USB: M-Sys uDiskOnChip USB: Generic STORAGE Network: Realtek Boot Agent Description Set the type of device for the first drive BIOS attempts to boot from. If Realtek Boot Agent is selected, system will attempt to load boot sector from the Ethernet port. Set the type of device for the second drive BIOS attempts to boot from.
Exit Setup BIOS SETUP UTILITY Main Advanced Exit Options Save Changes & Exit Discard Changes & Exit Discard Changes Security Boot Exit Exit system setup after saving the changes. F10 key can be used for this operation. Load Optimal Defaults ←→ Select Screen ↑↓ Select Item Enter Go to the Sub Screen F1 General Help F10 Save and Exit ESC Exit (C) Copyright 1985-2004, American Megatrends, Inc.
5. UPGRADING YOUR COMPUTER This upgrade activity should only be performed by an adult. Upgrading the System Memory Module Many applications will generally run faster when the computer’s dynamic memory capacity is increased. The computer has a DDR2 memory socket, which is located underneath the keyboard. You can increase the amount of memory by replacing the existing one with a dual inline memory module (commonly known as SO-DIMM) of a higher capacity. The SO-DIMM can be 256MB, 512MB, or 1024MB in capacity.
Use a small blade to press the latch inward. The keyboard tray should pop up slightly over the latch. If the keyboard tray does not pop up, try to gently lift it up slightly above the latch. Repeat this step for the other keyboard latch. 4. 34 Carefully lift up the bottom edge and do not break-loose the flex-cable that connects to the keyboard. Turn the keyboard and the metal cover over, and then the DDR DIMM Socket is revealed.
5. To remove an old DIMM from the socket, press out on the latches located on both edges of the socket at the same time. The DIMM should pop up to an angle of 30 degree (see diagram below). Pull the DIMM module out of the memory socket. Store the DIMM for the future use. 6. Install the new DIMM module into the memory socket. The DIMM will only fit in one orientation. Insert the DIMM at an angle of approximately 30 degrees into the empty memory socket.
7. Pivot the DIMM until the latches on both sides of the socket snap into place. Notice the notch on the DIMM. The notches should fit nicely with the socket. 8. Put the metal cover and the keyboard back to their original position. Make sure the bottom edge of the keyboard now resides under the spring-loaded latches. You may need to use a small pin to push in the latch first, otherwise the keyboard will not fit in. Congratulations! You have just completed the memory upgrade.
Your computer has been tested with a wide range of DIMM on the market. However, not all memory modules are compatible. Check with your system vendor for a list of compatible DIMM for your computer. Upgrading the Mass-Data-Storage Device To upgrade the mass-data-storage capacity, you can either replace the existing M-System flash storage module with one that has a higher capacity, or instead, replace it with the 1.8 inch P-ATA-type hard disk drive module.
38 3. Gently lift the old module and replace it with the new one. When you do this, be sure that the flash module connector is properly seated on the main-board, as the connector may be attached to the old flash module. The connector is what links the flash module to the system board. 4. 5. Re-attach Screw A. Put the metal cover and the keyboard back to their original position. Make sure the bottom edge of the keyboard now resides under the spring-loaded latches.
Congratulations! You have just completed the flash module upgrade. You may need to reformat the new flash storage module and re-install O/S, drivers, and all the necessary applications. Installing the Optional Hard Disk Drive Module To replace the flash storage module with the hard disk drive module, do the following: 1. 2. Follow the first four steps in the previous section, Upgrading the System Memory Module, to access the hard disk drive bay. Locate and remove one Screw A.
40 3. Gently lift the old module. Be sure that you remove the flash connector as well. You need to remove the existing flash module in order to install the hard disk drive module. 4. The HDD module comes with a metal casing and a flexcable with HDD connector. Place the HDD module into the HDD module bay and join together the two HDD connectors as shown below.
5. Put the metal cover and the keyboard back to their original position. Make sure the bottom edge of the keyboard now resides under the spring-loaded latches. You may need to use a small pin to push the latch in first, before you lower the keyboard.
Congratulations! You have just completed the hard disk drive installation. You may need to reformat the new drive and re-install O/S, drivers, and all the necessary applications.
6. TROUBLE SHOOTING The trouble shooting activity should only be performed by an adult. Your computer has been fully tested and complies with the system specifications before shipping. However, incorrect operations and/or mishandling may cause problems. This chapter provides a reference for identifying and correcting common hardware and software problems that you may encounter. When you encounter a problem, you should first try to go through the recommendations in this chapter.
• • Some software programs, which have not gone through rigorous coding and testing, may cause problems during your routine use. Consult the software vendor for problem solving. Be sure to go to BIOS SETUP and load DEFAULT SETTING after BIOS re-flash. Audio Problems No speaker output • • Software volume control is turned down in Operating System’s Sound System or is muted.
• Make sure the source of noise is indeed from the hard drive and not the fan or other devices. The hard disk drive has reached its capacity • • Archive files or programs that you had no longer used by moving them to an alternative storage medium (card reader, etc.) or uninstall programs that are no longer used. Many browsers store files in the hard drive as a cache to speed up the performance.
• Try restarting the system. The characters on the screen repeat while I type. • • You may be holding the keys down too long while you’re typing. Keep the keyboard clean. Dust and dirt under the keys could cause them to stick. Memory Problems The POST does not show an increased memory capacity when you have already installed additional memory • • • Certain brands of memory module may not be compatible with your system. You should ask your vendor for a list of compatible DIMM.
• Make sure the Ethernet cable is connected to the hub socket that supports 100Base-TX mode. The hub may have both 10Base-TX and 100Base-T sockets. Performance Problems The computer becomes hot • • • • In a 35oC environment, the certain areas of the computer’s back case are expected to reach 50 degrees. Make sure the air vents are not blocked. If the fan does not seem to be working at high temperature (50 degrees Celsius and up), contact the service center.
48
Appendix: Specification Processor and Core Logic ¾ Intel Celeron M, Ultra Low Voltage version Core Logic ¾ Intel 915GMS+ICH6-M chipset with graphic, audio, and USB2.
PnP Function ¾ Plug and Play compatible Flow Control ¾ Automatic Jam and auto-negotiation for flow control ¾ Auto Negotiation and Parallel detection for automatic Speed Selection ¾ Speed selection (IEEE 802.3u) ¾ High performance 32-bit PCI bus master architecture with integrated DMA controller for low CPU and bus utilization Other Features ¾ Remote Wake-up Scheme supported ¾ Hot Insertion supported Mass Data Storage ¾ NAND-type, 1GB / 2GB ¾ P-ATA 1.
Adapter ¾ Autosensing AC-in 100~240V, DC-out 20V, 65W or 40W BIOS ¾ AMI PnP BIOS ¾ Power On Self Test ¾ DRAM auto-detection, auto-sizing ¾ L2 Cache auto-detection ¾ Hard disk type auto-detection ¾ ACPI 2.0 (Advanced Configuration Power Interface) ¾ Two Level Password Protections ¾ 32bit access, Ultra DMA, PIO5 Mode support ¾ Multi-boot capability Operating System ¾ Compatible with Microsoft Windows XP Pro ¾ Linux Physical Specification ¾ 244 (W) x 191.2 (D) x 35.4 (H) mm ¾ 1.38KG / 3.
