G731001
Preface Copyright 2003 All Rights Reserved. The information in this document is subject to change without prior notice in order to improve reliability, design and function and does not represent a commitment on the part of the manufacturer. In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use the product or documentation, even if advised of the possibility of such damages.
Limitation of Liability While reasonable efforts have been made to ensure the accuracy of this manual, the manufacturer and distributor assume no liability resulting from errors or omissions in this manual, or from the use of the information contained herein. Notices Federal Communications Commission Radio Frequency Interference Statement NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Table of Content Chapter 1: Introduction------------------------------------------------- 1 Welcome to the Notebook PC ------------------------------------------------ 2 Getting to Know Your Computer -------------------------------------------- 2 Opening the LCD Panel------------------------------------------------- 2 The Left Side ------------------------------------------------------------- 5 The Right Side ----------------------------------------------------------- 7 The Rear ----------------------------
Preparing the Battery Pack for Use-----------------------------------26 Automatic Battery Pack Charging Function ------------------------26 Battery Status -----------------------------------------------------------27 Battery Low Warning --------------------------------------------------27 Small Battery for the Real Time Clock ------------------------------28 Resetting the System ---------------------------------------------------28 Adjusting the Brightness-----------------------------------------------29 C
Installing the LAN Driver for Win2K/Me/XP ----------------------47 Installing the TouchPad Driver for Win2K/Me/XP ----------------48 Manual Installation -----------------------------------------------------------48 Installing the MiniPCI Modem Driver for Win2K/XP-------------49 Installing the MiniPCI Modem Driver for WinME ----------------49 Installing the CardBus Driver for WinXP ---------------------------50 Installing the CardBus Driver for Win2K ---------------------------50 Installing the CardBus Drive
Notice: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Shielded interface cables and a nonshielded AC power cord must be used in order to comply with emission limits. This equipment is to be used with power supply: I/P: 100-240 Vac, 50-60Hz,1.5A O/P: 19Vdc, 4.74A or I/P: 100-240 Vac, 50-60Hz, 20A O/P: 20Vdc, 6A There is no internal power supply.
5. Please keep this equipment from humidity. 6. Lay this equipment on a reliable surface when isntall. A drop or fall could cause injury. 7. Make sure to use the right voltage for the power source when connecting the equipment to the power outlet. 8. Place the power cord in such a way that people can not setp on it. Do not place anything on top of the power cord. 9. All cautions and warnings on the equipment should be noted. 10.
max. 35°C. 16. The sound pressure level at the operators position according to IEC 704-1: 1982 is equal or less than 70 dB(A). 17. Power Cord Requirements The power cord set used with the AC adaptor must meet the requirements of the country where you use the AC adaptor, whether it is 100-120 or 200-240 Vac. The following information explains the requirements for power cord set selection. The cord set must be approved for the country in which it is used.
18. The cord set must have a current capacity of a least 2.5 Amperes and voltage rating of 125 or 250 Vac. When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons. These precautions includes the following: 1. 2. 3. 4. Do not use this product near water, for example, near a bathtub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool.
7. Beachten Sie beim Anschluß an das Stromnet die Anschlußwerte. 8. Verlegen Sie die Netzanschlußleitung so, daß niemand darüber fallen kann. Es sollte auch nichts auf der Leitun abgestellt werden. 9. Alle Hinweise und Warnungen, die sich am Gerät befinden, sind zu beachten. 10. Wird das Gerät üeinen längeren Zeitraum nicht benutzt, sollten Sie es vom Stromnetz trennen. Somit wird im Falle einer Überspannung eine Beschädigung vermieden. 11.
Entsorgung gebrauchter Batterien nach Angaben des Herstellers. 15. Dieses Schaltnetzteil kann bis zu einer Außentemperatur von maximal 35ºC. 16. Die Ausgangswerte dürfen nicht die auf dem Label angegebenen Werte überschreiten. 17. Anforderungen an das Stromkabel Das Kabel-Set, das an das Netzteil angeschlossen wird, muss den Anforderungen des Landes, in dem Sie das Netzteil einsetzen, genügen, je nachdem, ob die Netzspannung 100-120 oder 200-240V Wechselspannung beträgt.
18. Das Kabel muss vom HAR (harmonisierten) Typ H05VV-F sein. Das Kabel-Set muss eine Stromkapazität von mindestens 2,5 Ampere haben und Spannungen von 125 oder 250 V Wechselstrom gestatten. Bei der Benutzung Ihres Telefongerätes sollten Sie immer die grundlegenden Sicherheitsmaßnahmen beachten, um das Risiko von Feuer, Stromschlägen und Verletzungen zu minimieren. Zu beachten sind u.a. folgende Punkte: 1. 2. 3. 4.
Personal Inventory This Notebook computer system is designed for years of productive and pleasurable computing. Use this section to keep notes about details of your purchase. Update this section when you add new options.
Chapter 1 Introduction WAR NIN G: T h e r e a r e mo r e a n d m o r e p e o p le s p e n d i n g l a r g e amounts of time in front of computer monitors now that scientists from many fields including anatomy, psychology, and occupational safety are involved in the study of ergonomically sound w ork environments. A few tips to help you work effectively without a lot of physical discomfort: • Purchase a chair with armrests and good back support. Don't slouch when sitting; keep your back straight.
Welcome to the Notebook PC Congratulations on your purchase of the Notebook PC. Your Notebook features the latest advances in portable computing technology. The Notebook’s modular design provides maximum expandability without compromising portability. The high-performance CPU and enhanced IDE hard drive provides you with extra processing power for handling complex graphics and running large programs. One PCMCIA slot gives you the ability to use standard PCMCIA cards, such as a LAN adapter or memory cards.
Each of these features is briefly described below. 1. LCD Cover Release Latch - Slide this latch to the right to open the LCD cover. 2. LCD Screen - Your Notebook computer is equipped with a replaceable color Liquid Crystal Display (LCD) screen that supports up to 1024 x 768 or 1400 x 1050 x 16M LCD resolution utilizing a AGP BUS. A built-in backlight allows you to comfortably view the screen even when ambient lighting is low. 3.
4. Power/Resume Button - Pressing this button for 1-2 seconds will turn on the system or pressing this button when the computer is in Suspend mode will resume normal operation. Pressing this button for 4-6 seconds will also turn off the system. 5. TouchPad - The TouchPad is hardware-compatible with the IBM PS/2 mouse and software-compatible with the Microsoft mouse. 6. TouchPad Buttons - The buttons below the TouchPad correspond to the left and right buttons on a standard mouse.
Indicates when the keyboard is in Caps Lock mode. In this mode, the keyboard produces uppercase text when you press a key. When you press the Caps Lock key again, the indicator goes off and the keyboard produces lowercase text. Indicates when the keyboard is in Scroll Lock mode. Some applications will move information across the screen differently when Scroll Lock is on. 9. The Built-in Microphone - The built-in microphone is located to the left of the TouchPad. 10.
NOTE: When using a LAN, please use an EMI Shielding Cable to minimize an inteference when transmitting. 3. 1394A (Option) - A very fast external bus standard that supports data transfer rates of up to 400 Mbps (400 million bits per second). Can be used to connect up 63 external devices, also supports isochronous data -delivering data at a guaranteed rate. This makes it ideal for devices that need to transfer high levels of data in real-time, such as video devices.
The Right Side 1. The CD-ROM/DVD-ROM or DVD CD-RW Combo (Option) - Your Notebook comes with a swappable 24X (or higher) 5.25" IDE CD-ROM or 8X DVD-ROM. 2. USB Ports - Your computer includes four Universal Serial Bus (USB) port. USB is the latest development in Plug and Play technology. It will eventually replace the need for separate connectors for external keyboards, serial ports, and parallel (printer) port. The Rear 1.
synchronous signal and de-multiplexes audio and other digital data. 2. External Microphone Jack - This mono microphone jack is used to connect an external microphone. 3. Infrared Data Port - The Infrared Data Port allows your Notebook to become truly wireless. You can use this port to transfer large amounts of data very quickly to any other machine (Notebook computers, printers, etc.) which is also equipped with an IrDA-compliant IR port.
The Bottom Panel 1. Battery - Your notebook comes equipped with a factoryinstalled battery pack module. After the battery runs down, the module can be removed and replaced with a charged battery. 2. Expansion Compartment - This compartment will serve as an expansion to upgrade your RAM module. 3. CD-ROM Release Latch - Push this latch to release the CD-Rom from its bay. 4. Battery Release Latch - Lift up this latch to release the battery from its bay. 5.
10
Chapter 2 Getting Started Connecting to a Power Source Connecting the AC Adapter A universal AC adapter is provided to supply your computer with power and also charge the computer’s battery pack. The adapter’s AC input voltage can range anywhere from 100 to 240 volts, covering the standard voltages available in almost every country. The power cord for the AC adapter requires a three-hole grounded AC outlet. To connect the computer to an external power source: 1.
CAUTION: The best kind of AC power source to connect your Notebook to is a UPS (Uninterruptible Power Supply). Lacking this, use a power strip with a built-in surge protector. Do not use inferior extension cords as this may result in damage to your Notebook. The Notebook comes with its own AC adapter. Do not use a different adapter to power the computer and other electrical devices. Whenever possible, keep the AC adapter plugged into the Notebook and an electrical outlet to recharge the battery.
CAUTION: Always wait at least 5 seconds after turning off your Notebook before turning it back on; turning the power on and off in rapid succession can damage the Notebook’s electrical circuitry. Turning On Your Notebook Computer Turn on your Notebook by pressing the power button. Hold the button down for a second or two and release. The Power-On Self Test (POST) runs automatically.
NOTE: Only use batteries that are approved by an authorized dealer. All batteries are not the same and therefore should not be treated as such. Using the wrong battery could cause serious damage to your computer and yourself through toxic emissions. Inserting and Removing the Battery Pack The battery pack should already be inserted in your Notebook computer when you unpack it. If not inserted, follow these directions: 14 1.
3. Gently lower the battery into the bay and push it until it clicks securely in the bay. To remove the battery pack: 1. Turn off the notebook, and disconnect the AC adapter. Close the LCD panel and turn it over and place it on a solid, flat surface. 2. Lift the release latch to release the battery from the bay. At this time the battery will now be angled slightly out of the bay. 3. Hold the battery at the finger grip and lift it out of the compartment.
Charging the Battery Pack The installed battery pack charges automatically any time the computer is connected to the AC adapter and an external power source. It is a good idea to occasionally discharge the battery pack fully to preserve its operating performance. NOTE: Battery Charging Step 1: Discharge the battery and recharge until it reach full charge capacity. Step 2: A fully charge battery must be discharge to less then 95% capacity then recharge the battery.
C hapter 3 Using the Notebook Co mputer Adjusting the LCD Screen Display The LCD screen display can be adjusted by the following key combinations. KEYS FUNCTIONS [Fn] + [F7] Decreases the brightness level. [Fn] + [F8] Increases the brightness level. [Fn] + [F10] Use this key combination to expand your video screen or reset to its original size. [Fn] + [F12] This key combination toggles the display between the LCD, CRT, simultaneous LCD/CRT, TV, simultaneous CRT/TV.
LCD Care LCD screens are delicate devices that need careful handling. Please pay attention to the following precautions: • When you are not using the computer, keep the LCD screen closed to protect it from dust. • If you need to clean your LCD screen, use a soft tissue to gently wipe the LCD surface. • Do not put your fingers or sharp objects directly on the surface and never spray cleaner directly onto the display. • Do not press on, or store any objects on the cover when it is closed.
The function keys (F1-F12) on the top row of the keyboard, serve different purposes and carry out different tasks depending on the application you are running. The cursor (arrow) keys (which are all located in the lower right corner of your keyboard) and the [PgUp], [PgDn], [Home] and [End] keys (which are located along the right edge of the keyboard) allow you to move the active cursor of the computer to various locations on the screen or within the document.
The Notebook’s Hot Key Controls KEYS FUNCTION(S) Power Button Press this button once to power on or enter the suspend/resume mode. Press this button for more than 4 seconds to power off the system. Internet Button Open Internet WWW Home short-cut key Email Button Open Email Reader short-cut key [Fn] + [F2] This key combination turns on/off the volume. [Fn] + [F3] Decreases the speaker volume. [Fn] + [F4] Increases the speaker volume. [Fn] + [F7] Decreases the brightness level.
• Do not rest heavy objects on the TouchPad or the TouchPad buttons. You can use the TouchPad with Microsoft Windows as well as non-Windows applications. Connecting an External Tracking Devices The system will only enables you to use one tracking device whether it is an internal or external tracking device. Data Storage and Retrieval Data storage and retrieval are two of the most fundamental tasks you will perform when working with your computer. The Notebook is equipped with a 3.
• 12.7mm height Precautions for Handling CD-ROM/DVD-ROM/Combo Discs • Always hold the disc by the edges, avoid touching the surface. • Use a clean, dry, cloth to remove dust, smudges, or fingerprints. Wipe from the center outward. • Do not write or place objects on the surface of the disc. • Store discs in a cool dry place not to damage the disc. • Do not use benzene, thinners, or cleaners with detergent. Only use CD-ROM/DVD-ROM cleaning kits. • Do not bend or drop the discs.
NOTE: Do not insert any foreign objects into the disc tray. If you experience difficulty when ejecting the CD disk tray, stretch a paper clip (or use a pin or a thin metal rod) and insert it into the emergency eject hole located on the right side of the front panel. The CD disk tray should eject immediately. This procedure can also be used to remove a CD from the drive when the Notebook is powered off. Removing the CD-ROM/DVD-ROM/Combo Drive 1.
PCMCIA Cards and Expansion Sockets The Notebook features one PCMCIA expansion socket design to interface with one Type II card. Inserting a PCMCIA Card The computer will emit a medium tone followed by a high tone when a PC card is inserted. When you eject a card, the computer will emit a high tone followed by a medium tone. You can insert and remove a PC card whether the computer is turned On or Off. Follow these instructions to insert a PCMCIA card: 1.
CAUTION: Always disconnect all telephone lines from the wall outlet before servicing or disassembling this equipment. To reduce the risk of fire, use only No. 26 AWG or larger telecommunication line cord. Power Saving Modes This section contains information on the Notebook’s power system, including the AC Adapter, the battery system, recharging the battery, and tips for conserving battery power. The power system is comprised of two parts, the AC Adapter and the battery system.
Preparing the Battery Pack for Use Before using the battery pack for the first time, the Smart Battery IC within the battery pack should be calibrated in order to get accurate reporting of remaining battery life status. To calibrate the battery pack follows the instructions below: 1. Insert the battery into the battery compartment and turn on the Notebook. If the battery is completely without power go to the next step. Otherwise, let the battery run down until the battery lowlow warning beeps are heard.
Fast 3.5 hours (88.8Whr) or 2.5 hours (59.2Whr) with the system off or in Suspend mode. The temperature must be 25°C or below room temperature. Pre-Charge A pre-charge is supplied to the Li-Ion battery pack. Battery Status Windows ME/Windows 2000/Windows XP has an applet in the Control Panel that will display an icon in the Windows taskbar indicating when the Notebook is running on battery power or is attached to the AC adapter.
When there is only one minute of battery charge remaining, the Notebook will suspend to the HDD and power off. You should connect AC power and resume to save your work. Small Battery for the Real Time Clock There is a small built-in battery pack that supplies power to the system in order to maintain certain system information while the power is off. If the Notebook is left without a power source for long period of time, this battery will be exhausted and system information will be lost.
Adjusting the Brightness To adjust the brightness on the LCD screen, press and hold down the [Fn] key in the lower left hand corner of the keyboard and press the [F7] key to reduce the brightness or [F8] to increase the brightness.
30
Chapter 4 Desktop Operation Your notebook is capable of providing you with efficient and productive mobile computing, it also has the speed and capacity to service as a desktop system. This chapter discusses those functions of your notebook that are typical of desktop systems. Audio The Multimedia Sound System The Notebook’s built-in audio capabilities allow you to take advantage of a wide range of education and entertainment multimedia software.
External audio devices can be connected to the Line in jack. All audio features are software controlled.
NOTE: For a high-quality sound, click on the "Volume Control" at the lower right end of your screen. From the Volume Control windows, click on the "Advanced" tab, click and select the "Microphone Boost" item. Playing Sound Files Your notebook can play audio files stored in MIDI, WAVE or MP3 file format. Check the Help and Support Center in Windows for information on the functions of the Media Player.
34
Chapter 5 Running BIOS Setup Introduction The BIOS (Basic Input and Output System) Setup program is a menu driven utility that enables you to make changes to the system configuration and tailor your system to reflect installed hardware or alter system performance. When the notebook computer is turned back on, the system is configured with the values stored in CMOS. Navigating through BIOS Setup The Setup program has been designed to make it as easy to use as possible.
Accessing the BIOS Setup Program To access the BIOS Setup program, press the Del key after the notebook computer has run through its POST. Item Specific Help On the right side of the Setup screen is an area labeled Item Specific Help. This area will list navigation key shortcuts and information that is specific for the item that you are currently editing. The Menu Bar The top of the screen has a menu bar with the following selections: Standard CMOS Setup Set the time and date. Configure disk drives.
The Legend Bar At the bottom of the Setup screen you will notice a legend bar. The keys in the legend bar allow you to navigate through the various setup menus. The following table lists the keys found in the legend bar with their corresponding alternates and functions. Function Legend Key Esc Jumps to the Exit menu or returns to the Main menu from a submenu. ↑ or ↓ Moves the cursor up and down between fields. PgUp/PgDn Set to modify the field selected.
Date/Time The current values for each category are displayed. Enter new values through the keyboard. Pri Master, Sec Master Select one of these hard disk drive icons to configure the hard disk drive named in the option.
The Advanced CMOS Setup When the Setup program is accessed, the following screen appears: Quick Boot Set this option to Enabled to instruct AMIBIOS to boot quickly when the computer is powered on. The settings are Disabled or Enabled (default value).
completes. The settings are Disabled, IDE-0, CD/DVD and USB FDD (default value). 2nd Boot Device This option sets the type of device for the second boot drives that AMIBIOS attempts to boot from after AMIBIOS POST completes. The settings are Disabled, IDE-0, CD/DVD (default value) and USB FDD. 3rd Boot Device This option sets the type of device for the third boot drives that the AMIBIOS attempts to boot from after AMIBIOS POST completes. The settings are Disabled, IDE-0 (default value), CD-ROM and USB FDD.
The settings are 4M/8M/16M/32M/64M (default value)/128M/256M USB Keyboard/Mouse/FDD Legacy Support Set this option to Enabled to enable support for older keyboards and mouse devices if the USB Function option is set to Enabled. The settings are Enabled or Disabled. The Peripheral Setup TV Display Type This field allows you to choose the television display option when using the TV out port. The settings are PAL, NTSC (default value).
TV PAL Display Type This field allows you to choose the television PAL system type. The settings are PAL (default value), PAL-M, PAL-N. IR Port Support This option specifies the IR port address for the IR Port. The settings are Disabled or Enabled (default value). IR Mode Select This option specifies the infrared transmission method. The settings are SIR or FIR (default value). OnBoard Parallel Port This option specifies the base I/O port address of the parallel port on the motherboard.
Change Supervisor Password This field allows you to set the Supervisor password. To set the Supervisor password, highlight this field and press the [Enter] key. The following dialog box appears: Enter new supervisor password: Auto Configuration with Optimal Settings The optimal default settings are best-case values that should optimize system performance. To set the configuration, highlight this field and press the [Enter] key.
Exit Without Saving This option should only be used if you do not want to save the changes you have made to the Setup program.
Chapter 6 The Software Utilities Disks There are two separate procedures on how to install the driver: AutoRun installation and Manual installation. AutoRun Installation • Follow the step-by-step procedures on the CD-ROM/DVDROM to execute the “AutoRun” application by selecting the topic of “Driver Installation”. • To re-run the “AutoRun” installation, please refer to the procedures on the “Manual Installation” for a more detailed explanation.
NOTE: If you encounter this message when executing the Auto Run program in Windows 2000, please perform the following procedures: Click on the “Start” – “Setting” – “Control Panel” – “System” – “Advanced” tab – “Performance” tab – “Change” tab – reduce the maximum Virtual Memory setting to 200MB. Installing VGA Display Drivers for Win2K/ME/XP This section describes the operation and installation of VGA display software drivers supplied on the Driver Utility CDROM that is shipped with your computer. 46 1.
Installing the Audio Driver for 2K/Me/XP To install the audio driver you must first remove the currently installed driver. 1. Insert the CD-ROM Driver into your CD-ROM/DVDROM drive. 2. Click “Start” and Select “Run”. 3. Type the following: D:\Driver\Audio\Setup.exe (If D is not your CD-ROM/DVD-ROM drive, substitute D with the correct drive letter). 4. Click on “Setup” to begin the Installation Wizard. 5. Follow the Wizard’s on-screen instructions to complete the installation. Restart the system.
1. Insert the CD-ROM Driver into your CD-ROM/DVDROM drive. 2. Click “Start” and Select “Run”. 3. Type the following: D:\Driver\LAN\Setup.exe (If D is not your CD-ROM/DVD-ROM drive, substitute D with the correct drive letter). 4. Click on “Setup” to begin the Installation Wizard. 5. Follow the Wizard’s on-screen instructions to complete the installation. Restart the system.
Installing the MiniPCI Modem Driver for Win2K/XP Please follow these instructions to install the Modem driver: 1. From your screen, click on the "My Computer" icon and use your mouse or touchpad right button to select the "Properties" item. 2. Click on the "Hardware" tab from the "System Properties" dialog window. 3. Double click "Device Manager" tab. 4. Select the "PCI Device" in the "Other Devices" group (denoted by a yellow mark symbol). 5.
5. Select the "Specify a location" item. 6. Click "Browse" button and specify for the designate location of your CD driver. Installing the CardBus Driver for WinXP Please follow these instructions to install the cardbus driver: 1. From your screen, click on the "My Computer" icon and use your mouse or touchpad right button to select the "Properties" item. 2. Click on the "Hardware" tab from the "System Properties" dialog window. 3. Double click the "Device Manager" button. 4.
CardBus Controller" and click on the "Driver" tab. 5. Click the "Driver" tab then click the "Update Driver" item. 6. Select the "Search for a suitable driver for my device (recommended)" item and click "Next". 7. Select the "Specify a location" and click "Next". 8. Click "Browse" button and specify for the designate location of your CD driver. Installing the CardBus Driver for WinME Please follow these instructions to install the cardbus driver: 1.
Display Modes The SiS's driver support three output namely: LCD, VGA and TV. Before proceeding, be sure the monitor is connected to the computer. Driver Mode This define the two status of Single, Mirror and Multi Monitor (when an external monitor is connected to your notebook computer).
When the "Single" is selected, the display can only be seen on the notebook computer LCD, VGA or TV panel. When the "Mirror" is selected, you can display different combination between the LCD, VGA or TV display. Display Combination This applies to the display that you prefer to use. REMINDER: The "Auto" tab will serve as additional function of the "Mirror" and "VGA" respectively by removing the check mark under the "Display Combination" selection field.
1. Click on the “Control Panel” and double click on the “Display” icon. Click on the “Settings” tab to enter the “Display Properties” window. Click on the “Advanced” button. 2. From the “SiS 650 Properties” window, click on the “Display Modes” tab. Select the "LCD”, “VGA” or "TV" tab by clicking on the button to enable and connect the video display to the external display screen. 3. Click on the “Apply” tab and you will be ask to keep the new setting.
enable the monitor that you have chosen. Click “Yes” to accept the change. Click the “Apply” tab to run the function and restart the computer. 4. After the system has restarted, your notebook computer LCD screen and the external monitor screen are connected with each other. From the LCD display, open the “Display Properties” and use the cursor to drag it to the right thus moving the image to the external monitor screen.
After you have restarted Windows, open the “Control Panel” and double click on the “Display” icon. From the “Display Properties” window, select the “Settings” tab and click on the “Advanced” tab to enter the "SiS 650 Properties" window. You will notice four new entries have been made in the "Utility Manager" window: Gamma Correction, Video Setting, Driver Mode Setting and Product File Information. Gamma Correction You can adjust the right color for your window screen by moving the “Tint” adjustment window.
Video Setting 57
This dialog box has the following scroll bars and buttons for controlling the color components of the video image. Brightness Use this scroll bar to adjust the overall intensity of light emitted by the video display. Contrast Use this scroll bar to adjust the contrast level between the bright and dark areas of the video image. The highter the contrast, the brighter the bright areas and the darker the dark areas, and vice versa.
Driver Mode This define the two status of Single, Mirror and Multi Monitor (when an external monitor is connected to your notebook computer). When the "Single" is selected, the display can only be seen on the notebook computer LCD, VGA or TV panel. When the "Mirror" is selected, you can display different combination between the LCD, VGA or TV display. Display Combination This applies to the display that you prefer to use.
Option: Single This function will only show one single display whether it be on your notebook computer or external monitor. Option: Mirror (Simultaneous Display) This function supports different combinaton of LCD, VGA and TV display. 1. Select the "LCD" , “VGA” or "TV" tab by clicking on the button to connect the video display to the external CRT screen. 2. Click on the “Apply” tab and you will be ask to keep the new setting.
Chapter 7 Troubleshooting This chapter describes locating and solving problems that you may encounter while using your computer. Locating a Problem Problems with your computer can be caused by something as minor as an unplugged power cord – or as major as a damaged hard disk. The information in this chapter is designed to help you find and solve minor problems.
drives, or you get an error message during the Power-On Self Test (POST). Software errors can occur at several levels. The ROM BIOS and the operating system can give you a large number of error messages. On top of this, each application software package has its own set of error messages. It is important to determine whether the software error message you are getting is from the application or the operating system. Once you know this, you can look in the respective manual for a solution to the problem.
devices, look for loose or disconnected cables. If the computer is too close to a wall, a cable connection may be loose or the cables may be crimped. NOTE: Do not substitute cables for different devices (other than the manufacturer recommended cables) even if they look exactly alike. The wiring inside the cable may be different. When you are certain that you have power available and all connections are good, turn the computer on again. If the computer still does not start, you may have a hardware problem.
• Messages that furnish important information on the poweron and boot processes (such as memory status). These noncritical malfunctions are those that cause incorrect results that may not be readily apparent. An example of a noncritical error would be a memory chip failure. In general, if the POST detects a system board failure (a critical error), the computer halts and generates a series of beeps.
time, your CMOS battery may be depleted. Contact your dealer to change the battery. Problem: The message: “Invalid system disk, Replace the disk, and then press any key” appears during boot. Solution: Check and make sure that you do not have a non-bootable floppy diskette inserted in your floppy drive. If your FDD is empty, you may not have an operating system installed on your drive. Contact technical support for assistance.
Solution: Ensure that the disk has been formatted. Consult your operating system manual for information on formatting floppy diskettes. Problem: The diskette is write-protected. Eject the diskette, remove the write protection, and try again. Solution: The diskette if full. Try using another diskette or free up some space on the diskette. The disk drive is not operating. Contact your dealer for support. Problem: You cannot use the mouse. • Check the cable connection.
Chapter 8 Upgrading your System Upgrading your Memory Refer to the following instructions and illustration for information on upgrading your notebook's memory.
1. Turn off the computer and disconnect the AC adapter and all peripherals. 2. Turn the notebook over so that the rear ports are facing you and locate the memory module compartment. 3. Remove the screws that secure the RAM module compartment cover to the chassis and set it aside. Slide the cover to the direction of the arrow. Locate the RAM modules. 4. Using your fingers or a small screwdriver, press the grips on the side of the RAM module away from the modules.
3. Gently hold the grip of the HDD and release it from its socket. 4. Use your thumb to push the grip downward to lift up the HDD to completely release the HDD from its compartment. CPU Upgrade To upgrade your CPU, follow the procedures below: 1. Turn the notebook over so that the rear ports are facing you. 2. Locate for the expansion compartment. 3. Unscrew and remove the cover of the CPU compartment.
4. Remove all the screws attached to the heatsink. 5. Before removing the screws, there are certain measures to followed in removing the heatsink 6. To remove the heatsink, first loosen the screw carefully. REMINDER: After loosening one screw, be certain that the next to be loosen should be the screw on its adjacent side as shown on the illustration.
Warning: Be sure to loosen all the screws first before removing it totally to release the heatsink. Failure to do so will cause a major damage to the heatsink. Now you can totally remove all the screws also in that order when you first loosen the screw. To insert the heatsink, follow the procedures below: 1. Make sure it is in slant position aligning with the socket of the compartment. 2. Slowly push down and insert the heatsink into its socket until it is properly seated into the expansion compartment.
72
Appendix A Specifications Detailed Notebook Specifications General CPU • Intel FCPGA2 P4 series 1.4GHz/1.5GHz/1.6GHz/1.7GHz/1.8GHz CPU, 256KB L2 cache on die, CPU front-side bus 400MHz • Intel FCPGA2 Northwood series 2.0GHz/2.2GHz/2.4GHz CPU, 512KB L2 cache on die, CPU front-side bus 400MHz • Intel FCPGA2 Celeron series 1.7/1.8/2.0GHz(0.
• Two 200 pin DDR SO DIMM type memory slots • 2.5V DDR SDRAM module • Supports 133 MHz Synchronous DRAM Core Logic • SiS650+961 PCMCIA Sockets • 1 Type II, support CardBus Pointing Devices • Synaptics TouchPad Keyboard • Keyboard controller: NS PC87591 • 12 function keys, Windows function keys • Language supported: US, Japanese, European etc.
• USB 1.1 port x 4 • MIC-in, headphone jack w/ adaptor for 5.1 channel SP/DIP support • RJ-11 jack for Fax/Modem • RJ-45 jack for LAN • One FIR • IEEE 1394 mini-jack (option) Mass Storage Hard Disk Drive • Standard Capacity: 10GB or higher • Type: 2.5" (MCC Specification) IDE • Height: 9.5mm CD-ROM/DVD-ROM/Combo Drive • 2.5" 12.7 mm CD-DOM.DVD-ROM/CD-RW drive • Factory option: built-in CD-ROM or DVD-ROM/CD-RW Video System Display • 15.0" XGA TFT • 14.
• Charge modes System off or in Suspend mode 3.5 hours (88.8Whr) charge time Mechanical Dimensions • Weight: • Size: 3.9KG (8.59 lbs) with 14.1" panel, battery and DVD-ROM drive installed 332.0mm (W) x 281.0mm (D) x 37.9mm/44.
Software Specifications System Software • System BIOS: AMI BIOS • Video BIOS: SiS650 • Supported Operating Systems Optional Windows XP Home/Professional or above version Optional Windows ME or above version Optional Windows 2000 or above version • Standard Software Drivers VGA driver Audio driver 1394 driver (option) TouchPad driver Modem driver LAN driver Cardbus driver 77
