i -1
Notice The information in this user’s manual is subject to change without notice. THE MANUFACTURER OR RESELLER SHALL NOT BE LIABLE FOR ERRORS OR OMISSIONS CONTAINED IN THIS MANUAL AND SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL DAMAGES, WHICH MAY RESULT FROM THE PERFORMANCE OR USE OF THIS MANUAL. The information in this user’s manual is protected by copyright laws. No part of this manual may be photocopied or reproduced in any form without prior written authorization from the copyright owners.
TABLE OF CONTENTS PREFACE Symbols and Conventions Protecting Your Computer - Avoid Abusive Handling and Adverse Environment Chapter Summaries 1.
Leaving the BIOS Setup Screen (2-3) BIOS Action Keys (2-3) Modifying the BIOS Settings (2-4) Main Setup (2-4) Advance Setup (2-4,5) Security Setup (2-5,6) Power Setup (2-6) Boot Setup (2-7) Exit Setup (2-8) 3.
Keyboard and Mouse Problems (5-9) CMOS Battery Problems (5-10) Memory Problems (5-11) Network Adapter / Ethernet Problems (5-12) Performance Problems (5-13) Firewire (IEEE1394) and USB2.
Preface Using This Manual This User’s Manual contains general information about the hardware and software setup, troubleshooting, and technical specifications of the notebook computer. Symbols and Conventions The following conventions and symbols are used in this manual: When keys are to be pressed at the same time, a plus (+) symbol is used. For instance, Fn+F7 means holding Fn and F7 keys at the same time. When a series of clicking actions is needed in Windows O/S, [ ] and > symbols are used.
Protecting Your Computer - Avoid Abusive Handling and Adverse Environment Follow the advice below will help ensure that you get the most out of your Investment. Your computer will serve you well if you take good care of it. Do not expose the computer to direct sunlight or place it near sources of heat. Do not subject it to temperatures below 0oC (32oF) or above 35oC (95oF). Do not expose the computer to magnetic fields. Do not expose the computer to moisture or rain.
Keep the adapter away from children. The total ampere ratings of the equipment plugged in should not exceed the ampere rating of the cord if you are using an extension cord. The total current rating of all equipment plugged into a single wall outlet should not exceed the fuse rating. Do not connect other AC adapter to your notebook.
Chapter Summaries The following is a summary of the available chapters and appendices in this manual. Chapter 1: Getting to Know the Basics In this chapter, you will learn the basic operations and features of your computer. It gives you a general understanding of the components of your computer. Chapter 2: BIOS Setup / Security In this chapter, you will learn how to change various firmware settings and what the settings mean.
■ chapter 1 getting to know the basics C H A P T E R ▼ O N E GETTING TO KNOW THE BASICS This chapter introduces the features and components of the computer.
■ chapter 1 getting to know the basics Performance Features 1-2 High Performance Processor with Intel 945GM Chipset The notebook PC is equipped with a powerful Mobile Intel Yonah dual-core (Core Duo) or Mobile Intel Yonah single-core (Core Solo) processor. Together with the latest Intel chipset and technologies, the system offers very advanced PC performances. Advanced Graphic Engine The Intel 945GM Express chipset is integrated with the next-generation Intel Graphics Media Accelerator GMA950.
■ chapter 1 getting to know the basics ExpressCard Technology ExpressCard (type I, 34mm) is the next-generation of the PC Card standard. The bus interface is based on the two standards: PCI Express for high-performance I/O and USB2.0 for variety of devices. Expandability The system offers upgradeable hard disk drive and 2 DDRII SDRAM sockets for expansion, allowing the user to easily increase the storage and system capacities as the need arises.
■ chapter 1 getting to know the basics System At A Glance Top View 1. LCD Display The panel is where the system content is displayed. 2. LED Status Indicator The LED Status indicators reveal the status of the system power state, battery-charging state, Instant-On/Suspend state, and the WLAN switch enabling and disabling.
■ chapter 1 getting to know the basics Status Indicator Section for details. 3. Keyboard The keyboard is used to enter data. (See Keyboard Section for details.) 4. Touch Pad The touch pad is a built-in pointing device with functions similar to a mouse. 5. Built-in Microphone The built-in microphone records sound. 6.
■ chapter 1 getting to know the basics Press the power / suspend button again to return from the suspend mode. (See Chapter 3 for more details on system suspend function.) When the system is in Suspend Mode, the indicator shows blinking green light.
■ chapter 1 getting to know the basics Front View Warning: Do not place any heavy objects on the top of notebook. This may damage the display 1. Wireless On/Off Switch Use the Switch to disable or enable the Wireless function. When Wireless LAN function is enabled, the indicator shows steady blue light. LED status 2. Built-in Stereo Speakers The built-in speakers output the sound in stereo. 3. Ventilation Grill The fan grill is where air is exchanged to dissipate the internal heat.
■ chapter 1 getting to know the basics Side Views Warning: Do not place any heavy objects on the top of notebook. This may damage the display 1. Optical Drive and Disk Eject Button and Manual Eject Key Hole If your computer comes with the Combo drive, DVD-Dual or Super-Multi drive, you may save data onto a CD-R / CD-RW or DVD RW disc. Press the eject button to eject the disk tray. The manual eject keyhole allows you to manually eject a jammed disk. 2.
■ chapter 1 getting to know the basics 3. Power Jack (DC-in) The DC-out jack of the AC Adapter connects here and powers the computer. 4. Antenna Connector for DVB-T Digital Video Broadcast TV (Optional Device) There is an antenna connector on the left side of the notebook. If your system has the DVB-T option, you should plug the antenna into the connector. Please see DVB-T Digital Video Broadcast TV section later in this chapter for more information.
■ chapter 1 getting to know the basics 9. ExpressCard Slot The slot is where Express Card (Type I, 34mm) is inserted. ExpressCard integrates both the PCI-Express bus technology and USB2.0 interface. Press the card into the slot to insert. Press the card again to eject. 10. Stereo Headphone / SPDIF-out Jack The stereo headphone jack (3.5-mm diameter) is where you connect the headphones or external speakers.
■ chapter 1 getting to know the basics Bottom View 1. Battery Pack and Battery Latch The battery pack is a built-in power source for the notebook. Slide the battery latch to release the battery pack. 2.
■ chapter 1 getting to know the basics heat. Do not block this airway completely. Warning: Do not block the Fan Grill outlet. Place the machine on hard surface only. The bottom case may get very hot. 3. System Device Cover The system’s processor with cooler assembly, Wireless LAN module, HDD, and DDR memory module are located under the case cover. The system memory can be upgraded to a larger capacity. (See Chapter 4 for instructions on the memory and HDD upgrade.) 4.
■ chapter 1 getting to know the basics AC Adapter 1. DC-out Connector The DC-out connector docks to the power jack (DC-in) on the computer. 2. Adapter The adapter converts alternating current into constant DC voltage for the computer. 3. AC Plug The AC plug plugs to the AC wall outlet.
■ chapter 1 getting to know the basics LED Status Indicator The LED Status Indicator displays the operating status of your notebook. When a certain function is enabled, an LED will light up. The following section describes its indication. System & Power Status Indicators LED Graphic Symbol Indication Blue light indicates the WLAN module is active. Persistent green light indicates the Silent Mode is enabled. Blinking green light indicates the notebook is in the suspend mode.
■ chapter 1 getting to know the basics OSD Status Indicator The On-screen Status Display Indicator displays the operating status of your notebook. When a certain function is enabled, the symbol will show up on windows. The following section describes its indication.
■ chapter 1 getting to know the basics Keyboard Features Function Keys (Quick Keys) Graphic Symbol Action System Control Fn + F1 Enters Suspend Mode. Fn + F3 Turns of the battery warning beep off or on. Fn + F4 Changes Display Mode: LCD-only, CRT-only and LCD&CRT. Fn + F5 Turns Speaker Volume up. Fn + F6 Turns Speaker Volume down. Fn + F7 Increases Display Brightness. Fn + F8 Decreases Display Brightness. Fn+Num Lk Enables the embedded keypad to work in numeric mode.
■ chapter 1 getting to know the basics Windows Keys Your keyboard also has two Windows keys: 1. Start Key This key allows you to pull up the Windows Start Menu at the bottom of the taskbar. 2. Application Menu Key This key brings up the popup menu for the application, similar to a click of the right mouse button. Embedded Numeric Keypad Press Fn+Num Lk to enable the embedded numeric keypad. The numbers are printed in upper right corner of a key, in a color different from the alphabets.
■ chapter 1 getting to know the basics Touch Pad The built-in touch pad, which is a PS/2-compatible pointing device, senses movement on its surface. As you move your fingertip on the surface of the pad, the cursor responds accordingly. The following items teach you how to use the touch pad: 1. Move your finger across the touch pad to move the cursor. 2. Press buttons to select or execute functions. These two buttons are similar to the left and right buttons on a mouse.
■ chapter 1 getting to know the basics Graphic Subsystem Your computer uses a high performance 12.1-inch active matrix TFT panel with high resolution and multi-million colors for comfortable viewing. The Intel integrated GMA950 video graphics accelerator, which is Microsoft DirectX 9 compatible, performs graphic rendering at a lighting-fast speed. Adjusting the Display Brightness The notebook uses special key combinations, called hot keys, to control brightness. Press Fn+F7 to increase the brightness.
■ chapter 1 getting to know the basics Opening and Closing the Display Panel To open the display, lift up the lid. Then tilt it to a comfortable viewing position. The LCD panel has a maximum opening of 135 degrees. Do not push it down forcibly. To close the display cover, fold it down gently. Warning: To avoid damaging the display, do not slam it when closing.
■ chapter 1 getting to know the basics DVB-T Digital Video Broadcast TV (Optional Device) The optional DVB-T (Digital Video Broadcast – Terrestrial) module allows you to watch high-quality digital video broadcast TV on your notebook computer. If your system has the DVB-T option, you should plug the antenna into the connector. You may have to move the antenna close to the window and away from the building for best reception.
■ chapter 1 getting to know the basics 3. Click the Program tab on the Settings dialog box and click Scan to scan for available channels. If a program (channel) is found, it will be included in the program list. When finished, you can choose a program and edit its name.
■ chapter 1 getting to know the basics 4. 5. Press Ok and close the Settings dialog box. You are ready to watch TV. If you system comes with the DVB-T Module already installed, you may use NewSoft Presto!PVR to watch and record the TV programs. Please see Chapter 4 if you are installing the DVB-T module by yourself. You also need to install the NewSoft Presto!PVR application from the CD to watch and record TV programs.
■ chapter 1 getting to know the basics Audio Subsystem Your computer’s audio subsystem is Sound Blaster Pro-compatible. Adjusting the Volume Manually To increase the volume, press Fn+F5. To decrease the volume, press Fn+F6. Adjusting the Audio Volume in Windows 1. Click the speaker symbol in the task tray in Windows. 2. Drag the volume control bar up or down to adjust the volume. 3. To temporarily silence the speaker without changing the volume setting, click Mute.
■ chapter 1 getting to know the basics Instant-On Multimedia Player (Optional) Instant-On Multimedia Player is an easy way to play DVD disc or video clips, view pictures, listen to music, and watch digital broadcast TV (if the optional DVB-T Module is installed). Instant-On does not work under Windows. Note: The following is an easy guide for Instant-On Player. For more information, please refer to its user guide or Help screen.
■ chapter 1 getting to know the basics Media File Storage: Using Instant-On to playback files, you need to store them in: C:\Documents and Settings\All Users(and every created users)\Documents\My XXX (Example: Photo files under \My Photo, Music files under\My Music and Video files under \My Video). For example, the first time you are in the Video Mode, the system will ask to scan the files stored under the specified file directory and then create a playlist for future use.
■ chapter 1 getting to know the basics Use the ←→ keys to select the Media Mode. Use F1 to show the Instruction Menu for that Media Mode. Shutting Down the Instant-On Player: Press the Instant-On Player button to shut down the computer.
■ chapter 1 getting to know the basics Ethernet Your computer is equipped with a 10/100/1000Base-TX Fast Ethernet network adapter. Connect the active LAN cable to the RJ-45 LAN port located on the left side of the computer. This allows you to access and transmit data in the local area network. Connecting to the Network Use Unshielded Twisted Pair (UTP) Ethernet cable only. 1. Insert one end of the UTP cable into the network connector until the connector snaps securely into the receptacle. 2.
■ chapter 2 bios setup and security feature C H A P T E R ▼ T W O BIOS SETUP AND SECURITY FEATURE In this chapter, you will learn how to enter the BIOS Setup Menu and manipulate various hardware control settings. You will also learn how to use the built-in security features.
■ chapter 2 bios setup and security feature The Setup Utility is a hardware configuration program built into your computer’s BIOS (Basic Input/Output System). It runs and maintains a variety of hardware functions. It is a menu-driven software, which allows you to easily configure and change the settings. The BIOS contains manufacture’s default settings for the computer’s standard operations. However, there are occasions when you may be required to modify the default settings in the BIOS.
■ chapter 2 bios setup and security feature Entering the BIOS Setup Screen First turn on the power. When the BIOS performs the POST (Power-On Self Test), press F2 key quickly to activate the AMI BIOS Setup Utility. Note: You may need to press F2 key fairly quickly. Once the system begins to load Windows, you may have to retry by cycle-power on again Leaving the BIOS Setup Screen When you have finished modifying the BIOS settings, exit the BIOS. It takes a few seconds to record changes in the CMOS.
■ chapter 2 bios setup and security feature Modifying the BIOS Settings The AMIBIOS setup main menu is subdivided into sub-menus. Each menu item is described in this section. Main Setup Under this menu, you may change time/date and view basic processor and system memory information. Item Date Selections / Sub-menu N/A Time N/A Description Type in the current date, in MM/DD/YY format. Type in the current date, in HH:MM:SS format.
■ chapter 2 bios setup and security feature storage device. Item Selections / Sub-menu TouchPad Enabled Disabled Support LCD Auto DIMM Function Enable Disable Description Enable or disable the built-in touchpad. [Enable]: The system automatically reduces the LCD brightness when AC power is removed to save power. [Disable]: The LCD brightness remains the same whether or not AC power is present.
■ chapter 2 bios setup and security feature 1. System always asks for password every time it is powered on. 2. System asks for password only when you attempt to enter BIOS utility. The passwords are encrypted and stored in NVRAM. Make sure you write them down or memorize them. If you lost the passwords, the computer may need to be sent back to the factory or to an authorized service dealer to reset the passwords.
■ chapter 2 bios setup and security feature Boot Setup ►Boot Settings Configuration Item Selections / Sub-menu Quiet Boot Disabled Enabled Description When Enabled, the system will display OEM logo instead of the POST messages. When Disabled, the system will display POST messages (i.e. devices information.) ►Boot Device Priority Item 1st Boot Device Selections / Sub-menu Removable Dev. CD/DVD Hard Drive Network Disabled Description Set the type of device for the 1st drive BIOS attempts to boot from.
■ chapter 2 bios setup and security feature Exit Setup Item Selections / Sub-menu Description Saves Changes and Exit N/A After you have completed the BIOS settings, select this item to save all settings, exit BIOS Setup utility, and reboot. New system settings will take effect on next power-up. F10 key can be used for this operation. Discard Changes and Exit N/A Discards changes done so far to any of the setup questions and exit.
■ chapter 3 battery power & power management C H A P T E R ▼ T H R E E BATTERY POWER & POWER MANAGEMENT In this chapter, you will learn the fundamentals of power management and how to use it to achieve longer battery life.
■ chapter 3 battery power & power management In this chapter, you will learn how to operate your notebook on battery power, how to handle and maintain the battery pack, and learn about the system’s power saving features. TFT display, central processor, hard disk drive are the major hardware subsystems that consume the most power. Power management deals how these key components should behave to conserve power.
■ chapter 3 battery power & power management Battery Low-Power Warning 1. Low Battery Warning Low battery condition occurs when battery power is reduced to 6%. The green battery status LED indicator blinks and the system beeps once every 16 seconds or so. 2. Very Low Battery Warning Very Low battery condition occurs at 3 % power remaining. The green battery status LED indicator blinks and the system beeps at 4-second interval.
■ chapter 3 battery power & power management Installing and Removing the Battery Pack To Remove the Battery Pack: 1. Place the notebook bottom-side up on a flat and secured surface. 2. Push the latch and pull the battery’s hard case away from the notebook.
■ chapter 3 battery power & power management To Install the Battery Pack: 1. Place the notebook bottom-side up on a flat and secured surface. 2. Carefully insert the battery pack into the battery compartment of the notebook. Charging the Battery and Charging Time To charge the battery, while the battery pack is in the notebook, plug the AC adapter into the notebook and an electrical outlet.
■ chapter 3 battery power & power management Checking the Battery Level You can check the remaining battery power in the Windows battery status indicator, which is located at the lower right-hand corner of the task bar. (If you do not see a battery or AC-in icon on the task tray, go to Power Options Properties box and click on the Advanced tab. Check off ``Always show icon on the task bar``.) Alternatively, you can access the power meter by clicking the Power Options icon in the Windows Control Panel.
■ chapter 3 battery power & power management Using Windows Power Options Windows Power Management provides basic power saving features. In the Windows Power Options Properties [Start > Settings > Control Panel > Power Options] dialogue box, you may enter time-out values for display and hard disk drive. Windows power manager saves power by turning off hard drive after 1 minute of inactivity, for example.
■ chapter 3 battery power & power management In this dialog box, you can manually set the LCD and hard drive’s time-out values in the Plugged in column and in the Running on batteries column. Lower time-out values will save more battery power. Note: Also consult Windows user guide for more information on how to use Windows power management functions. Note: Actual dialogue box shown above may appear slightly different.
■ chapter 3 battery power & power management Suspend Mode Standby Suspend The system automatically enters this mode after a period of inactivity, which is set in the Power Schemes dialog box. In Standby mode, hardware devices, such as display panel and hard disk, are turned off to conserve energy. Hibernate Suspend In this mode, all system data are saved in the hard disk before powering down.
■ chapter 3 battery power & power management Note: Do not install or remove the memory module when the system is in the suspend mode. Note: Actual dialogue box shown above may appear slightly different.
■ chapter 3 battery power & power management Power Button Action The notebook PC’s power button can be set to turn off the system or activate the suspend mode. Go to [Start > Settings > Control Panel > Power Options] and click on the Advanced tab. In the pull-down menu, select how you wish the power button to work as. Note: Actual dialogue box shown above may appear slightly different.
■ chapter 3 battery power & power management Low Battery Warning You can define when and how the system warns you of its battery-low condition. Go to the Alarms tab in the Power Options Properties box. If you wish to hear audible beeps, click on the Alarm Action button and put a check on Sound Alarm. Note: Consult Windows user guide for more information on how to use Windows power management functions. Note: Actual dialogue box shown above may appear slightly different.
■ chapter 3 battery power & power management Power Menu Quick Access Instead of making specific selections in the Power Options Properties box, you can quickly and easily specify which pre-set power saving function you desire by clicking on the Battery icon at the lower right-hand corner of the task bar. (If you do not see a battery or AC-in icon, go to Power Options Properties box and click on the Advanced tab. Check off ``Always show icon on the task bar``.
■ chapter 4 upgrading your computer C H A P T E R ▼ F O U R UPGRADING YOUR COMPUTER In this chapter, you will learn how to upgrade the DRAM, hard disk drive, and to install the optional wireless LAN mini-Card and DVB-T Module. Warning: We strongly recommend that you return the notebook to the dealer or the shop for the hardware upgrade.
■ chapter 4 upgrading your computer Upgrading the Hard Disk Drive Replacing the original drive with one of larger capacity can increase the hard drive capacity of your computer. The computer uses a 9.5 mm (height), 2.5-inch Serial ATA type hard disk. Be sure to make a backup copy of all your data before attempting this operation. Warning: Hard drive upgrade is a delicate process. Please observe the following instructions carefully or have a qualified technician install it for you.
■ chapter 4 upgrading your computer Upgrading the Hard Disk Drive To replace the hard disk drive, do the following: 1. Turn OFF the computer. Unhook the AC cord and all cables/devices attached to the notebook. Remove the battery. 2. Place your hand on a large metal object momentarily to discharge any static electricity. 3. Locate and remove 7 Screw A’s. 4. Remove the System Device Cover.
■ chapter 4 upgrading your computer 5. Locate and remove 1 Screw B. 6. Push the HDD module to the right and separate it from the connector. Lift the module away from the bay. 7. Locate and remove 4 Screw C’s from the HDD module. Remove the metal case.
■ chapter 4 upgrading your computer 8. Re-attach the metal cover to the new hard drive and tighten 4 Screw C’s. 9. Re-attach the HDD module to the HDD connector. And re-attach Screw B. 10. Put the System Device Cover back and re-attach 7 Screw A’s. Congratulations! You have now completed the hard drive upgrade. When you boot up the PC, you may need to create a primary HDD partition and reformat the new drive and re-install O/S, drivers, and all the necessary applications.
■ chapter 4 upgrading your computer Upgrading the System Memory Many applications will generally run faster when the computer’s dynamic memory capacity is increased. The computer provides two DDR2 memory sockets. There is one located underneath the System Device Cover and another one located underneath the keyboard. You can increase the amount of memory by replacing the existing one with a dual inline memory module (commonly known as SO-DIMM) of a higher capacity.
■ chapter 4 upgrading your computer Installing a memory module (DIMM) into the system To install the DIMM under the System Device Cover, do the following: 1. Power OFF the notebook. Unplug the AC cord and all cables/devices attached to the notebook. Remove the battery. 2. Place your hand on a large metal object momentarily to discharge any static electricity. Place the notebook on a flat surface and fully close the LCD lid. 3. Locate and remove 7 Screw A’s on the System Device Cover. 4.
■ chapter 4 upgrading your computer 5. If you need to remove an old DIMM from the socket, press out on the latches located on both edges of the socket at the same time. The DIMM should pop up to an angle of 30 degree (see diagram below). Pull the DIMM module out of the memory socket. Store away the DIMM for the future use. 6. Install the new DIMM module into the memory socket. The DIMM will only fit in one orientation. Insert the DIMM at an angle of approximately 30 degrees into the empty memory socket.
■ chapter 4 upgrading your computer into the receiving socket. 7. Pivot the DIMM until the latches on both sides of the socket snap into place. Note: Notice the notch on the DIMM. The notches should fit nicely with the socket. 8. A’s.
■ chapter 4 upgrading your computer To install the DIMM under the keyboard, do the following: 1. Remove Screw D. 2. Find the keyboard latches near the edges of the keyboard. The latch is spring-loaded. It will retract when pressed and revert back to its original position when released. Use a small blade to press the latch inward. The keyboard tray should pop up slightly over the latch. If the keyboard tray does not pop up, try to gently lift it up slightly above the latch.
■ chapter 4 upgrading your computer 3. Carefully lift up the top edge and position the keyboard out of the way and the following is revealed. Locate and remove 2 Screw E’s on the Metal Cover.
■ chapter 4 upgrading your computer 4. If you need to remove an old DIMM from the socket, press out on the latches located on both edges of the socket at the same time. The DIMM should pop up to an angle of 30 degree (see diagram below). Pull the DIMM module out of the memory socket. Store away the DIMM for the future use. 5. Install the new DIMM module into the memory socket. The DIMM will only fit in one orientation.
■ chapter 4 upgrading your computer socket. Then press it firmly so that the contact edge is driven into the receiving socket. 6. Pivot the DIMM until the latches on both sides of the socket snap into place. Note: Notice the notch on the DIMM. The notches should fit nicely with the socket. 7. Put the Metal Cover back and tighten 2 Screw E’s. Put the keyboard back to its original position. Make sure the edge of the keyboard now resides under the spring-loaded latches.
■ chapter 4 upgrading your computer 8. Re-attached Screw D. Congratulations! You have just completed the memory upgrade. When you boot up the computer, you should expect to see an increase in DRAM capacity. Note: Your computer has been tested with a wide range of DIMM on the market. However, not all memory modules are compatible. Check with your system vendor for a list of compatible DIMM for your computer.
■ chapter 4 upgrading your computer Adding the Mini-Card Type Wireless LAN Card (Optional Device) Your computer comes with a unique Mini-Card socket, which is located underneath the System Device Cover. The socket allows the computer to add unique features such as wireless LAN (IEEE802.11x). Ask your dealer on the availability of the mini-card. Warning: Installing a mini-card is a delicate process. Please observe the following instructions carefully or have a qualified technician install it for you.
■ chapter 4 upgrading your computer Installing the Mini-Card into the System To install a new Mini-card, do the following: 1. Follow steps in the previous section, Installing a memory module (DIMM) into the system, to access the Mini-Card Socket underneath the System Device Cover. 2. The mini-card will only fit in one direction. Align the small notch in the module with the socket on the connector and insert the card at an angle of approximately 30 degrees into the empty socket.
■ chapter 4 upgrading your computer The card should pop up to an angle of 30 degree. 3. Locate 2 antenna cables with connectors. Snap the cable onto the golden connector on the wirelss mini-card. (Note: The connectors are fairly small! This may take some maneuvering. You may want to connect the antenna cables before inserting the wireless card into the socket. ) 4. Replace the System Device Cover and 7 Screw A’s. Congratulations! You have now completed the wireless mini-card installation.
■ chapter 4 upgrading your computer Adding the DVB-T Module (Optional Device) This section explains how to install the optional DVB-T Module to your computer. Warning: Installing the DVB-T Module is a delicate process. Please observe the following instructions carefully or have a qualified technician install it for you. Damages due to mishandling of this procedure are NOT covered by the manufacture’s warranty.
■ chapter 4 upgrading your computer Installing the DVB-T Module into the System To install the DVB-T Module, do the following: 1. Power OFF the notebook. Unplug the AC cord and all cables/devices attached to the notebook. Remove the battery. 2. Place your hand on a large metal object momentarily to discharge any static electricity. Place the notebook on a flat surface and fully close the LCD lid. 3. Remove Screw G and remove the DVB-T Device Cover. 4. The DVB-T Module will only fit in one direction.
■ chapter 4 upgrading your computer 5. Locate the antenna cable with connector. Snap the cable onto the golden connector on the DVB-T Module. (Note: The connector is fairly small! This may take some maneuvering. You may want to connect the antenna cable before inserting the card into the socket.) 6. Replace the DVB-T Device Cover and re-attach Screw G. 7. Connect the Antenna to DVB-T Antenna Connector on the left side of the computer.
■ chapter 5 trouble shooting C H A P T E R ▼ F I V E TROUBLE SHOOTING In this chapter, you will learn how to solve common hardware and software problems.
■ chapter 5 trouble shooting Your computer has been fully tested and complies with the system specifications before shipping. However, incorrect operations and/or mishandling may cause problems. This chapter provides a reference for identifying and correcting common hardware and software problems that you may encounter. When you encounter a problem, you should first try to go through the recommendations in this chapter.
■ chapter 5 trouble shooting hardware devices in the BIOS Setup utility. A faulty setting may cause the system to misbehave. If you are not sure of the changes you made, try to restore all the settings to factory defaults. Be sure all the device drivers are installed properly. For example, without the audio driver properly installed, the speakers and microphone will not work.
■ chapter 5 trouble shooting Audio Problems No speaker output Software volume control is turned down in Microsoft Sound System or is muted. Double-click the speaker icon on the lower right corner of the taskbar to see if the speaker has been muted or turned down all the way. Most audio problems are software-related. If your computer worked before, chances are software may have been set incorrectly. Go to [Start > Settings > Control Panel] and double-click the Sounds and Audio Devices icon.
■ chapter 5 trouble shooting Hard Disk Problems The hard disk drive does not work or is not recognizable If you had just performed a hard disk upgrade, make sure the hard drive connector is not loose and the hard disk drive is also correctly seated. Remove it and reinsert it firmly, and restart your PC. (Refer to Chapter 4 for details.) The new HDD may need to be partitioned and reformatted. O/S and drivers will need to be re-installed as well. Check the hard disk indicator LED.
■ chapter 5 trouble shooting for instructions on decreasing the cache size or on removing temporary Internet files. Empty the Recycle Bin to create more disk space. When you delete files, Windows saves them to the Recycle Bin. The hard disk takes longer to read a file If you have been using the drive for a period, the files may be fragmented. Go to [Start > Programs > Accessories > System Tools > Disk Defragmenter] to perform a disk defragmentation. This operation may take a while.
■ chapter 5 trouble shooting Optical Drive Problems The optical drive does not work Try rebooting the system. The disk is damaged or files are not readable. After you have inserted a CD-ROM disk, it may take a moment before you can access its content. The drive dose not read any disks The CD may not be properly seated in the tray. Make sure the disk is firmly seated onto the spindle. The disk is damaged or not readable.
■ chapter 5 trouble shooting Display Problems The display panel is blank when the system is turned on Make sure the computer is not in the Standby or Hibernate suspend modes. The display is turned off to conserve energy in these modes. The screen is difficult to read The display resolution should at least be set to at least1024x768 for optimal viewing. 1. Go to [Start > Settings > Control Panel] and double-click the Display icon. 2.
■ chapter 5 trouble shooting Keyboard and Mouse Problems The built-in touch pad performs erratically Make sure there is no excess perspiration or humidity on your hand when using the touch pad. Keep the surface of the touch pad clean and dry. Do not rest your palm or wrist on the surface of the touch pad while typing or using the touch pad. The built-in keyboard accepts no input If you are connecting an external keyboard to the system, the built-in keyboard may not work.
■ chapter 5 trouble shooting CMOS Battery Problem A message “CMOS Checksum Failure” displays during the booting process or the time (clock) resets when booting Try to reboot the system. If the message “CMOS Checksum Failure” appears during the booting procedure even after rebooting, it may indicate failure of the CMOS battery. If so, you need to replace the battery. This battery normally lasts two to five years. The battery is of type CR2032 (3V). You may replace it by yourself.
■ chapter 5 trouble shooting Memory Problems The POST does not show an increased memory capacity when you have already installed additional memory Certain brands of memory module may not be compatible with your system. You should ask your vendor for a list of compatible DIMM. The memory module may not be installed properly. Go back to Chapter 4 to review the details of this operation. The memory module may be defective.
■ chapter 5 trouble shooting Network Adapter / Ethernet Problems The Ethernet adapter does not work Go to [Start > Settings > Control Panel > System > Hardware > Device Manager]. Double-click on Network Adapters and check if Generic Marvell Yukon Chipset based Gigabit Ethernet Controller appears as one of the adapters. If it does not exist, Windows has not detected the Generic Marvell Yukon Chipset based Gigabit Ethernet Controller or the device driver has not been installed properly.
■ chapter 5 trouble shooting Performance Problems The computer becomes hot In a 35oC environment, the certain areas of the computer’s back case are expected to reach 50 degrees. Make sure the air vents are not blocked. If the fan does not seem to be working at high temperature (50 degrees Celsius and up), contact the service center.
■ chapter 5 trouble shooting Firewire (IEEE1394) and USB2.0 Problems The USB device does not work Windows NT 4.0 does not support USB protocols Check the settings in the Windows Control Panel. Make sure you have installed the necessary device drivers. Contact the device vendor for additional support. The IEEE1394 port does not work Go to [Start > Settings > Control Panel > System > Hardware > Device Manager]. You should see an entry which reads “OHCI Compliant IEEE 1394 Host Controllers”.
■ appendix A product specification A P P E N D I X ▼ A PRODUCT SPECIFICATION A-1
■ appendix A product specification Processor Core Logic Memory Type Default Memory Expansion LCD Panel Graphic Accelerator Motion Playback Other Features A-2 ▼ Processor and Core Logic z Mobile Intel Dual-Core Processor (Yonah), up to 2.16GHz, 2 MB L2 cache or z Mobile Intel Single-Core Processor (Yonah), up to 1.66GHz, 2MB L2 cache Intel Calistoga 945GM + ICH7-M chipset with audio, modem, and USB2.
■ appendix A product specification Chipset Audio Codec Sound Capabilities Module Transmission Protocol Chipset PnP Function Flow Control Speed Selection Other Features ▼ Audio Intel (ICH7M) integrated audio controller Realtek Audio Codec DirectSound 3D, EAX 1.0 & 2.0 compatible A3D, I3DL2 compatible AC97 V2.3 compatible Azalia compatible 2 Stereo Speakers ▼ Wireless LAN Intel PRO/Wireless 3945ABG Card Mini-Card Interface IEEE802.
■ appendix A product specification Chipset Capabilities Hard Drive Combo Drive DVD-Dual or Super-Multi Standards Keyboard Touch pad ▼ Firewire IEEE1394(a) 02 Micro 0Z128 IEEE1394 OHCI Host Controller Up to 400 Mbps Expandable up to 63 devices in chains ▼ Storage S-ATA 2.5-inch format hard disk drive 5.25-inch format (12.7mm height) fixed module (Optional Purchase) 5.25-inch format (12.
■ appendix A product specification Mic-In/Audioin Port Audio-Out / SPDIF Firewire USB2.0 Port Ethernet DVB-T Connector Power-In VGA Port Card Reader NewCard Slot Primary Battery Pack Feature Adapter AC-Input / DC-Output ▼ Ports and Connectors One Microphone-in / Line-in jack One Headphone / SPDIF-out jack One Firewire (IEEE1394) host connector Three USB2.
■ appendix A product specification PnP Function Self Test Auto Detection Power Management Security Other Features O/S Dimension Weight Environmental Limits A-6 ▼ BIOS AMI PnP BIOS Power On Self Test DRAM auto-detection, auto-sizing L2 Cache auto-detection Hard disk type auto-detection APM 1.2 (Advanced Power Management) & ACPI 2.
■ appendix B agency regulatory notices A P P E N D I X ▼ B AGENCY REGULATORY NOTICES B-1
■ appendix B agency regulatory notices Federal Communications Commission Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
■ appendix B agency regulatory notices EN55022 : 1998+A1: 2000+A2: 2003, CLASS B EN61000-3-2 : 2000 EN61000-3-3 : 1995+A1: 2001 EN55024 : 1998+A1 : 2001+A1: 2003 IEC61000-4-2: 2001 IEC61000-4-3:2002+A1:2002 IEC61000-4-4:1995+A1:2000+A2:2001 IEC61000-4-5:2001 IEC61000-4-6:2001 IEC61000-4-8:2001 IEC61000-4-11:2001 EN50082 (IEC801-2, IEC801-3, IEC801-4) Electro-magnetic Immunity EN 300 328-2, EN 300 328-1, EN 301 489-1, EN 301 489-17 (ETSI 300 328, ETSI 301 489) Electro-magneti
■ appendix B agency regulatory notices ''Notice: This equipment meets telecommunications network protective, operational and safety requirements as prescribed in the appropriate Terminal Equipment Technical Requirements document(s). This is confirmed by marking the equipment with the Industry Canada certification number. The Department does not guarantee the equipment will operate to the user's satisfaction.
■ appendix B agency regulatory notices 5-15P (15A, 125V) or NEMA 6-15P (15 A, 250V) configuration. Japan All components of the cord set (cord, connector, and plug) must bear a `PSE` mark and registration number in accordance with the Japanese Dentori Law. 2 The minimum specification for the flexible cord are: (1) 0.75 mm conductors, (2) Type VCT or VCTF, and (3) 3-conductor. The cord set must have minimum rated current capacity of 7 A.
■ appendix B agency regulatory notices CAUTION: MODEL X20IIx IS DESIGNED TO USE WITH THE FLLOWING AC ADAPTER MODEL ONLY Manufacture: LITE-ON ELECTRONICS, INC Model: P PA-1650-02 (65W), PA-1650-01 (65W) Manufacture: LI SHIN INTERNATIONAL ENTERPRISE CORP. Model: 0335A2065 (65W), 0335C2065 (65W) Manufacture: EPSF Model: 10653-A (65W) Telephone lines requirement The appropriate utilization of 26AWG telephone line cord on unit.
■ appendix B agency regulatory notices laws. VORSICHT! Explisionsgefahr bei unsachgernazen Austausch der Batterie. Ersatz nur durch denselben oder einem vom Hersteller empfohlenem ahnlichen Typ. Entsorgung gebrauchter Batterien navh Angaben des Herstellers. Laser Safety The optical drive used with this computer is certified as a Class 1 laser device according to the U.S.
■ appendix B agency regulatory notices ATTENTION: Il y a danger d’xplosion s’il y a remplacement incorrect de la batterie. Remplacer uniquement avcc unc batterie du meme type ou d’un type recommande par le constructer. Mettre au rebut les batteries usagees conformement aux instructions du fabricant. VORSICHT! Explosionsgefahr bei unsachgemBen Austausch der Batterie Ersatz nur durch denselben oder einem vom Hersteller empfohlenem ahnlichen Typ. Entsorgung gebrauchter Batterien nach Angaben des Herstellers.
