Installation Guide

Assembly Instructions for WS01-07
NOTE: USE TEFLON TAPE ON ALL THREADED CONNECTIONS
Shut off the water supply valve under the sink. Remove your old faucet and pop-up assembly.
Cover the sink drain so that no small parts are lost down it. Caution: Do not damage your old
water supply lines. Clean the surface of the sink in preparation for installing the new faucet.
FAUCET INSTALLATION:
1. Unscrew the bell from the hot valve body. Thread the brass nut, metal washer and rubber
washer downer the vlave body. Insert the hot valve body in the left hole of sink from
underneath. Screw the bell onto the valve body securely. Tighten the brass nut tight.
2. Unscrew the
brass locking nut (J), and remove the brass washer (I) and O-ring (H). Remove
the T-connector (G), and washer (F). Install the spout, large rubber rubber washer (B) and
spout base (A) in the center hole of the sink. Place the large rubber washer (B), metal
washer onto the threaded shank and secure with large lock nut (D). Tighten wrench tight.
Make sure the washer (F) is inside the T-connector (G), then re-attach the T-connector (G),
O-ring (H), brass washer (I) and brass nut (J). Tighten the brass lock nut (J) tight by using a
wrench.
3. Repeat step 1 for the cold valve body.
4.Attach supply hoses to each side of the T-connector (G) and to the outlets of the valve bodies.
5. Connect the supply lines (sold separately) to the treaded shanks. Tighten brass supply line
nuts securely. CAUTION: DO NOT OVERTIGHTEN.
6. Install handles.
POP-UP INSTALLATION:
1. Unscrew seat and top gasket from pop-up assembly.
2. Slip drain body through the drain opening and screw seat and top gasket onto the drain body.
3.Drop stopper into place. Remove pivot nut and insert pivot opening. Making sure the
pivot rod engages the stopper properly.
4.Remo ve sprin g cl ip from pivot rod and slide piv ot nut over p ivot rod a nd thre ad on to p ivot rod
open
ing. Tighten f irmly
, being
careful not to overtighten.
5. With lift rod in positing on the faucet, insert the lift rod through the lift rod strap and secure
with the set screw.
6. Guide the pivot rod through one the holes on the lift rod strap and secure it with the spring
clip, then adjust the height of the lift rod by resetting the set screw.
AFTER INSTALLATIONS IS COMPLETED, remove the aerator. Turn on the water supply
va lves an d a llow b oth hot and cold wat
er
to r un at le as t on e min ute e ach. W hi le wa ter is
r
u
nning
, che
ck for
leak
s, espe
ci
ally at
hoo
k-u
ps to sup
ply l
ines
. Tightening nuts slightly will
stop any minor leaks.
Assembly Instructions for Handles
Lever Handles:
1. Be sure that the broach screws are tightened installing the lever handles.
2. Install the lever handles on the broaches and tighten the set screws using the allen
wrench provided.
before
Cross Handles:
1. Remove the screws from the top of the broaches.
2. Remove the insert caps from the cross handles.
3. Put the cross handles on the broaches and then tighten the screws. Insert the caps on the
cross handles.
Broach
Broach
Screw
Set
Screw
Allen
Wrench
Aerator
Spout
A (Spout Base)
Bell
Supply Hose
B
C
Rubber Washer
Metal Washer
Valve Body
Outlet
Brass Nut
Cone Washer
Friction Ring
Brass Supply
Line Nut
Stopper
Seat
Top Gasket
Washer
Bottom
Gasket
Mounting Nut
Pivot Rod Opening
Drain Body
Lift Rod
Set Screw
Lift Rod
Strap
Spring Clip
Pivot Nut
B (Large Rubber Washer)
D
E
F
G
H
I
J
Rev.D
Elizabethan
Classics
R
NOTE: TO BE INSTALLED ONLY BY QUALIFIED, LICENSED PLUMBER
CAUTION: DO NOT OVER TIGHTEN NUTS AND SCREWS - THIS CAN LEAD TO
STRIPPING OR CRACKING AND WILL VOID YOUR WARRANTY.