Specifications

-6-
1.To install an in line heater, simply saw or cut out the center portion of the red heater blank at the breaking lines. The
threaded pieces should remain on both sides of the pipe section.
2. Insert the in line heater and tighten the unions of the in line heater to the remaining threaded portion of the heater blank.
Cleaning and Maintenance
Pump and pipe circulation system should be ushed before rst use and on a monthly basis when product is under normal
use. Below are the recommended procedures for cleaning:
• DO NOT RUN WHIRLPOOL DRY. Fill the tub with hot water 2-3 inches above the jets and add 2-3 teaspoons of low
foaming detergent such as dishwashing machine detergent. Make certain the air controls are turned completely clockwise
and are off.
• Switch on whirlpool and run for 10 minutes.
• Drain tub completely.
• Fill tub with cold water above jets.
• Switch on whirlpool and run for 15 minutes.
• Drain tub completely.
DO NOT USE ABRASIVE CLEANERS as they will scratch and dull the surface of the acrylic.
Plaster can be removed using a sharpened wooden stick. DO NOT USE METAL SCRAPERS, WIRE BRUSHES OR
OTHER HARSH ABRASIVE TOOLS. Usually a mild detergent will remove construction debris. More stubborn debris may
be removed with denatured alcohol, or Clorox Soft Scrub® cleaner. Light scratches and dulled areas may be restored to
original luster by rubbing with an automotive type cleaning compound such as DuPont White Polishing Compound®.
Air Baths and Total Massage Units are equipped with an Automatic Cleaning and Purge Cycle
Air Baths have a preprogrammed cleaning and purge cycle built in to expel the remaining water in the air channels. It
activates within 20 minutes after the bath is drained, blows for about 2 to 3 minutes and then shuts off automatically.
There is nothing to be alarmed about if you hear a blowing noise coming from the tub after the tub has been turned off.
The noise you hear is the cleaning cycle in operation.
Safety Features
Most models in the Eljer Premiere Series whirlpool line are provided with a suction system that releases the vacuum of the
pump when the suction face becomes obstructed. This provides an extra margin of safety. The pump responds instantly
when the suction system detects an obstruction and goes into a “standby” mode allowing the obstruction to be safely
removed. The pump instantly attains full ow when the obstruction is removed. The suction system is a mechanical device
that does not require springs or moving parts, resulting in service-free, durable operation.
Operating Instructions
1. Fill the bath at least to 3 inches above the jets before activating the pump.
2. The pump is activated by an on/off switch. Each depression of the button switches the power either on or off. Do not
repeatedly depress the switch in rapid order if you do not see the whirlpool function right away, as it may take a few
seconds before you can see it fully operating.
3. If any factory installed ttings are removed do not operate the unit. A safety hazard may occur.
4. Do not use bubble bath when you operate the whirlpool pump. This might cause excessive foaming.
5. Bath oils may be used; however their frequent use will require more frequent purging and cleaning
of the systems.
6. Both air and whirlpool systems are plumbed in a way that water will drain from the plumbing easily.
7. There are no user serviceable parts located under the tub.
ON-OFF SWITCH
The whirlpool bath pump is activated by a on-off switch. Each depression of the switch will
actuate the pump. If off, one depression will turn the pump on. If on, the next depression will turn it
off.
JET OPERATION AND ADJUSTMENT
The jets can be easily adjusted by pointing the jet-nozzle in the desired direction. For units with
Hydro Jets, the strength of the waterow and air induction can be regulated through twisting the
jet-nozzle. Twisting the nozzle clockwise will decrease the water ow and nally completly turn
off the water ow of that particular jet. If the nozzle is twisted counter- clockwise then the water
ow will increase up to its maximum ow.