TM STRATUS WHIRLPOOL INSTALLATION AND OPERATION MANUAL MODEL NUMBERS 2932J048 & 2940J048 THANK YOU... for selecting an Eljer bathing product. Your new bath is shipped to you after careful inspection. The whirlpool is completely assembled with pump and circulatory system piping. All you need to finish the installation are your selected fittings and electrical connections. To ensure maximum performance and pleasure from this product, please follow the instructions and cautions.
TABLE OF CONTENTS: Cover................................................................................................Page 1 Table of Contents..............................................................................Page 2 Safety Instructions Notice.................................................................Page 3 Installation, Framing and Post Installation Clean-Up Instructions.......................................................................
IMPORTANT SAFETY INSTRUCTIONS INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK OR INJURY TO PERSONS READ AND FOLLOW ALL INSTRUCTIONS! ! WARNING: Risk of personal injury. Do not permit children to use this unit without adult supervision. ! WARNING: Risk of personal injury. Do not operate this unit without the guard over the suction fitting. ! WARNING: Risk of electric shock. Do not permit electrical appliances (hair dryer, telephone, radio, etc.) within 60 inches (1524mm) of this unit.
Installation and Framing Instructions Each bath arrives ready for installation, completely equipped with the pump and plumbing necessary for operation. However, a drain/overflow kit is required for each bath and it is not included. The variety of installations for this bath may require framing procedures other than those shown. Locate studs as required. Ensure roughing-in dimensions are proper, plumb, and square. ! Remove the bath from the carton.
ROUGH-IN REFERENCES FOR RECESS TYPE INSTALLATIONS C D 12" (305 mm) W E NOTE: FRONT EDGE OF BATH MUST BE SUPPORTED BY STUD WALL OR ELJER APRON KIT LEVELING STRINGERS 24" (610 mm) ACCESS PANEL MUST BE LOCATED ON THE SAME SIDE AS THE MOTOR. ALLOW OPEN FRAMING ON PUMP/MOTOR END FOR SERVICE. ACCESS PANELS NOT REQUIRED FOR BATH TUBS UNLESS AN ACCESS OPENING OF AT LEAST 12" x 24" (305 x 610mm) IS PROVIDED, WARRANTY SERVICE WILL NOT BE PERFORMED.
ROUGH-IN REFERENCES FOR PIER TYPE INSTALLATIONS AS DESIRED F CUTOUT G CUTOUT C 12" (305 mm) AS DESIRED MOUNTING SURFACE WATERPROOF SEALANT BATH 24" (610 mm) ACCESS PANEL MUST BE LOCATED ON THE SAME SIDE AS THE MOTOR. ALLOW OPEN FRAMING ON PUMP/MOTOR END FOR SERVICE. ACCESS PANELS NOT REQUIRED FOR BATH TUBS UNLESS AN ACCESS OPENING OF AT LEAST 12" X 24" (305 X 610mm) IS PROVIDED, WARRANTY SERVICE WILL NOT BE PERFORMED.
SPECIFICATIONS: L W J C H SIDE VIEW A END VIEW B DRAIN / OVERFLOW GENERAL SPECIFICATIONS FOR WHIRLPOOLS Description 2932J048 5' x 32" Stratus Dimensions L-W-H Drain / Overflow L 59-3/4" (1518mm) A 17-3/4" W 31-3/4" (806mm) (451mm) H 22-1/2" (572mm) B 10-7/8" (276mm) Height to Underside of Deck: C Cut Out Pier GxF Rough-In Tub Edge to Recess Centerline ExD Overflow: J C 20-1/2" (521mm) 58-1/4" (1480mm) x 30-1/4" (768mm) 59-15/16" (1522mm) x 30-1/4" (768mm) 3-1/4" (83mm) Weight with Wate
SPECIFICATIONS: L W J H C SIDE VIEW A END VIEW DRAIN / OVERFLOW B GENERAL SPECIFICATIONS FOR WHIRLPOOLS Description 2940J048 6' x 36" Stratus Dimensions L-W-H Drain / Overflow L 71-3/4" (1822mm) A 17-3/4" W 35-3/4" (908mm) (451mm) H 22-1/2" (572mm) B 10-7/8" (276mm) Height to Underside of Deck: C Cut Out Pier GxF Rough-In Tub Edge to Recess Centerline ExD Overflow: J C 20-1/2" (521mm) 70-1/4" (1784mm) x 34-1/4" (870mm) 71-15/16" (1827mm) x 34-1/4" (870mm) 3-1/4" (83mm) Weight with Wate
ELECTRICAL INSTALLATION INSTRUCTIONS All wiring must be performed by a licensed electrician in accordance with the National Electrical Code and all other applicable codes. ! WARNING: When using electrical products, basic precautions should always be observed, including the following: 1. DANGER: RISK OF ELECTRIC SHOCK! Connect only to a circuit protected by a ground-fault circuit interrupter. 2. Grounding is required. The unit should be installed by a licensed electrician and grounded. 3.
Whirlpool Operation AIR SWITCH BATHING: • Fill bath with water at a comfortable bathing temperature - If your whirlpool is equipped with the optional field-installed heater, it will automatically maintain the water temperature. • IMPORTANT: Do NOT fill the whirlpool more than 2/3 full before getting in, as it may overflow. • IMPORTANT: Do NOT add bath oils or salts – this will damage the whirlpool pump.
Your Eljer whirlpool is designed to give you many years of pleasure with reasonable care and maintenance. Your new acrylic bathtub is tough, durable and easy to care for. The colors have been formulated to match other Eljer fixtures and enhance your choice of bathroom decorations. The high gloss surface will retain its lasting luster with proper care and maintenance. CLEANING AND MAINTENANCE: • Always fill the tub with temperate water. Excessively hot water (greater than 130˚ F) may cause surface damage.
AS AMERICA, INC. LIMITED LIFETIME WARRANTY FOR ELJER PREMIERE SERIES ACRYLIC TUBS AS America, Inc. (“American Standard”) warrants to the original consumer purchaser that it will, at its option, repair or replace this tub or any of its parts that are found by American Standard, in its sole judgment, to be defective under normal residential use and maintenance so long as it is owned by the original consumer purchaser. This limited warranty does not apply to commercial installations.