Installation Guide

ManualsBrandselk HOME ManualsCeiling Lightelk HOME 81505-3 Newland 3 Light 17 Inch Satin Brass Chandelier Ceiling Light

-1-

elkhome.com

1. Carefully pull house wires out of junction box so

they are easily accessible during installation.

2. Position mounting bracket (A) so threaded ends

of attached xture mounting screws (E) are

facing down towards oor.

3. Carefully pull house wires through hole in center

of mounting bracket (A).

4. Align holes in mounting bracket (A) with holes

in junction box.

5. Thread each junction box screw (B) into holes in

mounting bracket (A) and into hole in junction

box. Tighten junction box screws (B) to secure

mounting bracket (A) to junction box. CAUTION:

Make sure house wires are pulled completely

through hole in mounting bracket. DO NOT

pinch wires between mounting bracket and

ceiling.

JUNCTION

BOX

ITEM#: 81505/3

ITEM#: 81515/3

WARNING: DISCONNECT POWER AT THE MAIN

FUSE BOX BEFORE INSTALLATION.

WARNING:

This xture is intended for installation in

accordance with the National Electrical Code

(NEC) and all local code specications. If you are

not familiar with code requirements, installation

by a certied electrician is recommended.

Before assembly, remove all parts and part

packages from box. If anything is missing, please

contact the retailer from which the product was

purchased.

Français p. 4

Español p. 7

ANY QUESTIONS CALL: 800-613-3261

M-F 8:00AM-6:00PM ET

7. Push xture wires up through bottom of center

tube (P). Screw bottom of center tube (M) onto

threaded pipe on top of xture body (O).

8. Push xture wires up through bottom of top

trim (R). Thread top trim (R) onto top of center

tube (P).

6. Rotate arms until arms are evenly spaced apart.

Summary of content (9 pages)

PAGE 1
WARNING: DISCONNECT POWER AT THE MAIN FUSE BOX BEFORE INSTALLATION. WARNING: This fixture is intended for installation in accordance with the National Electrical Code (NEC) and all local code specifications. If you are not familiar with code requirements, installation by a certified electrician is recommended. ANY QUESTIONS CALL: 800-613-3261 M-F 8:00AM-6:00PM ET Before assembly, remove all parts and part packages from box.
PAGE 2
ITEM#: 81505/3 ITEM#: 81515/3 9. Carefully push fixture wires up through end of one 12 inch stem (M). Thread bottom of stem (M) onto top of fixture body (O). 10. Carefully push fixture wires through remaining stems (M). Screw stems (M) together keeping fixture wires taut. DO NOT pinch fixture wires between stems. 11. Carefully push fixture wires up through bottom of 6 inch stem (N). Pull fixture wires out of top of 6 inch stem (N). Screw bottom of 6 inch stem (N) onto top of stem (M). 12.
PAGE 3
ITEM#: 81505/3 ITEM#: 81515/3 15. Twist end of house lead wire (black) and end of fixture lead wire together. Twist wire nut (C) onto ends of wires. Completely tighten wire nut (C). Twist end of house neutral wire (white) and end of fixture neutral wire together. Twist wire nut (C) onto ends of wires. Completely tighten wire nut (C). Reference chart to the right for correct wire connections. 16. Wrap electrical tape (not included) around wire nuts (C) and wires.
PAGE 4
AVERTISSEMENT: COUPEZ L’ALIMENTATION ÉLECTRIQUE DU PANNEAU CENTRAL. AVERTISSEMENT : Ce luminaire a été conçu pour une installation selon les spécifications du code national de l’électricité et de tous les codes locaux. Si vous n’êtes pas familier avec les exigences de ces codes, une installation par un électricien certifié est recommandée. POUR TOUTE QUESTION, COMPOSER LE : 800-613-3261 L-V 8:00-18:00 HE Français Avant l’assemblage, retirer toutes les pièces et paquets de pièces de la boîte.
PAGE 5
ARTICLE#: 81505/3 ARTICLE#: 81515/3 9. Poussez soigneusement les fils du luminaire jusqu’à l’extrémité d’une tige de 30,48 cm (M). Enfilez l’extrémité de la tige (M) sur le dessus du corps du luminaire (O). 10. Poussez soigneusement les fils du luminaire à travers les tiges restantes (M). Vissez les tiges (M) ensemble en gardant les fils du luminaire tendus. NE PAS pincer les fils du luminaire entre les tiges. 11. Poussez soigneusement les fils du luminaire à travers la tige de 15,24 cm (N).
PAGE 6
ARTICLE#: 81505/3 ARTICLE#: 81515/3 15. Enroulez l’extrémité du fil de connexion de la maison (noir) et l’extrémité du fil de connexion du luminaire. Vissez un capuchon de connexion (C) sur les extrémités des fils. Serrez complètement le capuchon de connexion (C). Enroulez l’extrémité du fil neutre de la maison (blanc) et l’extrémité du fil neutre du luminaire. Vissez un capuchon de connexion (C) sur les extrémités des fils. Serrez complètement le capuchon de connexion (C).
PAGE 7
ADVERTENCIA: DESCONECTE LA ALIMENTACIÓN EN LA CAJA DE FUSIBLES PRINCIPAL. ADVERTENCIA: Este artefacto está destinado a ser instalado de acuerdo con el Código Nacional de Electricidad (NEC, por sus siglas en inglés) y todas las especificaciones del código local. Si no está familiarizado con los requisitos del código, se recomienda que la instalación sea realizada por un electricista certificado.
PAGE 8
ARTÍCULO#: 81505/3 ARTÍCULO#: 81515/3 9. Empuje con cuidado los cables del artefacto hacia arriba a través del vástago de 12 pulgadas (M). Jale los cables del artefacto hacia afuera de la parte superior del vástago de 12 pulgadas (M). Jale los cables del artefacto para tensarlos. Enrosque la parte inferior del vástago de 12 pulgadas (M) en la parte superior del cuerpo del artefacto (O). NO apriete los cables del artefacto entre el cuerpo del artefacto y el vástago. 10.
PAGE 9
ARTÍCULO#: 81505/3 ARTÍCULO#: 81515/3 15. Tuerza el extremo del conductor de la casa (negro) y el extremo del conductor del ensamble para unirlos. Gire el empalme plástico (C) en los extremos de los conductores. Apriete completamente el empalme plástico (C). Tuerza el extremo del conductor neutral de la casa (blanco) y el extremo del conductor neutral del ensamble para unirlos. Gire el empalme plástico (C) en los extremos de los conductores. Apriete completamente el empalme plástico (C).