INSTALLATION MANUAL Cross Platform Control Specifications, Installation and Programming This Manual pertains to both the ELK-M1G and the ELK-M1 models M1 includes the SIA CP-01 Standards for False Alarm Reduction TM
Introduction LIMITATION The ELK-M1G and ELK-M1 Controls are designed to warn against unauthorized entry and other situations. However, it is not a guarantee of protection against the occurrence of burglary, fire, or other emergency. Any alarm system is subject to compromise or failure to warn for various reasons. For example: - Unauthorized access can be gained through unprotected points or by disarming or bypassing protected points.
Table of Contents Specifications, Features, and Benefits ..................................................................................................... 5 Wiring & Hookup Diagram ........................................................................................................................... 6 Section 1 - Installation and Wiring ............................................................................................................. 8 1.1 Planning the Installation .......................
2200 Ohm EOL N.C. ZONE 2200 Ohm EOL N.C. ZONE N.O. 2200 Ohm EOL N.C. ZONE 2200 Ohm EOL N.C. ZONE NEG 2 3 Z2 Z3 N.O. T1 Cross Platform Control TM HOUSE PHONES Brown Red RING TELCO LINE Green TIP 16 Zones expandable to 208 Z5 N.O. NEG N.C. ZONE 2200 Ohm EOL N.C. ZONE N.O. 6 N.O. Strip Wires to 1/4" Length N.C. ZONE Z7 N.O. Alarm Contacts 2200 Ohm EOL N.C. ZONE N.O. 8 N.O. Z8 Z9 9 NEG 2200 Ohm EOL N.C. ZONE 2200 Ohm EOL N.C.
Specifications, Features, and Benefits The M1 is available in two models, the ELK-M1 Standard and the ELK-M1G Gold. The features and benefits which are common to both models is listed on the top section of this page. The bottom section highlights the key differences between both models.
Wiring & Hookup Diagram (Left Side Terminals) This unit provides Residential fire alarm service when installed according to ANSI/ NFPA 72-1993. This unit provides Grade A Residential Burglar alarm service. In conjunction with the enclosure, this unit also provides the following Commercial Burglar alarm service: Grade A Local, Police Connect with Basic Line Security, and Grades B & C Central Station.
J3 R1 T1 RING TIP J4 B A - Demark Block Tip RJ31X JACK (ELK-RJSET) Grey R1 Red Ring 4 Black T C + +12V HOUSE PHONES Yellow Aux Data Bus (J3) For wireless receiver. Presently works with ITI / Caddx NX408E, NX416E, or NX448E. See Programming Menu 14. NEG Compiles with FCC Part 68 Reg. Number: US:5K6AL03BELK-M1 Ringer Equivalence REN: 0.3B Use USOC RJ-31X connector.
Section 1 - Installation and Wiring 1.1 Planning the Installation The first step in any multi-zone security system installation is planning the job. 1. Read this entire manual to familiarize yourself with all system features and procedures before actually beginning the installation. Read all the information regarding Underwriters Laboratories (UL) and NFPA requirements. 2. Perform a physical survey of the installation site. Use the diagrams below as a guide in planning the installation. 3.
Keypad Mounting and Wiring Ideal keypad height is 50-58 inches above the floor. Select a location with an ambient temperature range between 32° and 120° F (0° to +49° C). Avoid direct sunlight if possible. Fasten mounting plate to electrical box (or directly to wall) using flat head screws to prevent shorts to the back of the circuit board. Keypads have a removable wiring plug for connecting to the M1 4-wire data bus. CAT5 or CAT6 eight (8) conductor cable is recommended for all Data Bus cables.
Two-Wire Smoke Zones (Zone 16) To enable the use of two-wire smoke detectors on Zone 16, move Jumper JP1 (located just below Zone 16 terminals) to the right side so that the two right hand pins are covered. Go to the installer programming mode, Menu 05 - Zone Definitions, and program Zone 16 as a Fire zone (Def=10). Step to the next location and program Wire Type=6. NOTE Use only compatible two-wire detectors as listed on the front label of the control. Do not mix brands.
AC Failure, Low Battery, and Automatic Low Voltage Shutdown During an AC power failure the battery automatically takes over and AC Fail trouble annunciates at the keypad. The communicator can be programmed to report AC Fail to the Central Station after a time delay (see Menu 12, System Option 01). If the battery voltage falls below 11.2 VDC a Low Battery Trouble condition will occur. The communicator can be programmed to report Low Battery to the Central Station.
Data Bus E.O.L. Termination - VERY IMPORTANT! Unlike many controls, the M1 features a true RS-485 “differential” data bus operating at 38,400 baud (bits per second). This is a relatively high speed by industry standards and was designed to ensure fast, accurate communications.
The ideal way to connect multiple home run cables is with an ELK-M1DBH Data Bus Hub. It accepts CAT5 or CAT6 cable with RJ45 plugs on the ends. It does all the work of series connecting the DATA lines A & B. Terminate at the hub using the included RJ45 Terminating Plug in the first unused jack. RS-485 DATA BUS Mount M1DBH inside control. Connect it to the M1 Data Bus terminals using a 4 conductor cable.
Section 2 - Operating the System 2.1 Introduction For best operation during bench testing, all zones should be terminated with end of line resistors and the correct transformer and battery should be connected to the unit. The control comes with factory default programming, allowing it to be bench tested prior to installation. The factory default code for user 1 is 3456. This code is authorized to operate all user related features of the system.
2.5 Keypad Overview Ready Light - This light is ON when all burglar zones are secure and the system is OK for arming. If this light is OFF, one or more zones are violated (not secure). For maximum security, all zones should be secured before the system is armed. If FLASHING, one or more force-armable zones are violated. Force arming temporarily excludes violated zone(s) from the system. However, if a force armed zone becomes secure while the system is armed, it will automatically restore to service.
123456789012345678901234567890 123456789012345678901234567890 123456789012345678901234567890 123456789012345678901234567890 123456789012345678901234567890 READY TO ARM 123456789012345678901234567890 123456789012345678901234567890 123456789012345678901234567890 9:00AM 08/01/03 123456789012345678901234567890 123456789012345678901234567890 Keypad Menus The control offers extended Menu Options via the center navigation “ELK” key. Some menus may require a valid code to authorize.
123456789012345678901234567890 123456789012345678901234567890 123456789012345678901234567890 123456789012345678901234567890 123456789012345678901234567890 3-Walk Test Area r 123456789012345678901234567890 123456789012345678901234567890 123456789012345678901234567890 < Area? Name > 123456789012345678901234567890 123456789012345678901234567890 123456789012345678901234567890 123456789012345678901234567890 123456789012345678901234567890 123456789012345678901234567890 000of016 Tested r 12345678901234567890123456
123456789012345678901234567890 123456789012345678901234567890 123456789012345678901234567890 123456789012345678901234567890 84-System r 123456789012345678901234567890 123456789012345678901234567890 123456789012345678901234567890 Tests 123456789012345678901234567890 123456789012345678901234567890 123456789012345678901234567890 123456789012345678901234567890 123456789012345678901234567890 123456789012345678901234567890 123456789012345678901234567890 1:Battery Test r 123456789012345678901234567890 123456789012
123456789012345678901234567890 123456789012345678901234567890 123456789012345678901234567890 123456789012345678901234567890 87-Custom 123456789012345678901234567890 123456789012345678901234567890 123456789012345678901234567890 Message Record r 123456789012345678901234567890 123456789012345678901234567890 123456789012345678901234567890 123456789012345678901234567890 123456789012345678901234567890 123456789012345678901234567890 123456789012345678901234567890 VM01b 1 Block(s) 123456789012345678901234567890 12
Multi-area (Partition) Operation 123456789012345678901234567890 123456789012345678901234567890 123456789012345678901234567890 123456789012345678901234567890 123456789012345678901234567890 0-Select Keypad 123456789012345678901234567890 123456789012345678901234567890 123456789012345678901234567890 Alternate Area r 123456789012345678901234567890 123456789012345678901234567890 123456789012345678901234567890 123456789012345678901234567890 123456789012345678901234567890 Auth.
Section 3 - Programming The Control 3.1 Introduction The Security functionality of the M1 Control can be programmed either from an ELK-M1KP LCD Keypad OR from the ELK-RP PC Software. The keypad features a menu-driven “Text” based interface with simple Yes/No answers for most options. After just a short amount of experience the average installer will not even require an instruction manual to keypad program the control. For the Automation functionality the ELK-RP PC Software is a requirement.
3.5 Communicator Setup Checklist The Communicator (Dialer) in the M1 can dial up to 4 telephone numbers in addition to the RP computer. The more powerful M1G can dial up to 8 phone numbers plus RP. Digital reporting formats include: Pulse 4+2, SIA, Contact ID, and Pager. There is also a Voice format which can be commanded from the RP Rules Programming to call a business, home, or cellphone and deliver a voice message. Use the following checklist for each required telephone number. 1. 2. 3. 4. 5. 6.
M1 Installation and Programming Manual Page 23 Menu 03 Area Defs Area 1 (1) Exit Delay 1 (2) Entry Delay 1 (3) Exit Delay 2 (4) Entry Delay 2 (5) Auto Stay (6) Exit Restart (7) Closing Ringback (8) SglKey Quickarm (9) DblKey Quickarm (10) StayKeyScroll (11) Stay Instant (12) Night Scroll (13) Night Instant (14) StayChgArmed (15) [Name] Menu 02 User Code Auth.
12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 01-Bus Module Enrollment r Menu 01 - Bus Module Enrollment Press RIGHT arrow key to select this menu.
12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 02-UserCode Optn Code used to: r Menu 02 - User Code Options Press RIGHT arrow key to select this menu.
12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 r 03-Area Definitions Area Defintions 123456789012345678901234567890121234 123456789012345678901234567890121234
Menu 03 - Area Definitions (continued) Area Definitions 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 A1 07:=No Sendr Closin
12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 04-Keypad Definitions r Keypad Definitions 123456789012345678901234567890121234 12345678901234567890123456789012
Menu 04 - Keypad Definitions (continued) Keypad Definitions Description of Option 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 To program the F1 key definitions press the right arrow key. The program will branch off 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 into the 7 options for this key.
12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 05-Zone Definitions r Zone Definitions Menu 05 - Zone Definitions Press RIGHT arrow key to select this menu.
Menu 05 - Zone Definitions (continued) Def Zone Description Operating Characteristics 15 Keyfob - Used when a wireless keyfob is enrolled into a receiver at this zone ID location. 16 No Alarm - Intended for use in Whenever/And/Then rules from the Remote Programming RP software. This zone type DOES NOT ACTIVATE any alarm and is not logged in the Event log. No reset is required. 17 Carbon Monoxide 24 hr - Activates an immediate Carbon Monoxide alarm if tripped anytime (armed or disarmed).
Menu 05 - Zone Definitions (continued) Zone Definitions 123456789012345678901234567890121234 123456789012345678901234567890121234 123456789012345678901234567890121234 123456789012345678901234567890121234 123456789012345678901234567890121234 123456789012345678901234567890121234 123456789012345678901234567890121234 123456789012345678901234567890121234 123456789012345678901234567890121234 123456789012345678901234567890121234 123456789012345678901234567890121234 ZN001 05: =Yes Dialer Delay r 123456789012345
12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 06-Alarm Cutoff Timers r Menu 06 - Alarm Duration Timers Press RIGHT arrow key to select this menu.
12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 07-Global System r Definitions Global Sys Definitions 123456789012345678901234567890121234 1234567890123456789012
Menu 07 - Global System Definitions (continued) Global Sys Definitions 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 G13:_ _ _ _ _ _ _ _r Common To Area1 Descr
Menu 07 - Global System Definitions (continued) Global Sys Definitions 123456789012345678901234567890121234 123456789012345678901234567890121234 123456789012345678901234567890121234 123456789012345678901234567890121234 123456789012345678901234567890121234 123456789012345678901234567890121234 123456789012345678901234567890121234 123456789012345678901234567890121234 123456789012345678901234567890121234 123456789012345678901234567890121234 123456789012345678901234567890121234 123456789012345678901234567890121
Menu 07 - Global System Definitions (continued) Global Sys Def 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 G38:=No Xmitr T
12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 08-Telephone r Account Setup Telephone Acct Setup 123456789012345678901234567890121234 12345678901234567890123456
Menu 08 Telephone Account Setup (continued) Telephone Acct Setup Description of Option 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 T1: 08:=000000r Acct # for
12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 09-Area Reporting Codes r Menu 09 - Area Reporting Codes Press RIGHT arrow key to select this menu.
Menu 09 - Area Reporting Codes (continued) Area Report Codes 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 AR1 11:Code= 00r Duress Code 12345678901234567890123
12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 10-Zone Reportng Codes r Menu 10 - Zone Reporting Codes Press RIGHT arrow key to select this menu.
12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 11-Keypad F-Keyr Reporting Codes Menu 11 - Keypad F-Key Reporting Codes Press RIGHT arrow key to select this menu.
12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12-Sys Rpt Code r Options & Codes Menu 12 - Sys Report Code Options & Codes Press RIGHT arrow key to select this m
Menu 12 - Sys Report Code Options & Codes (continued) Sys Rpt Code Options 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 SR11: T=00 R=00 r Low Battery 12345678
12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 13-User Codes Report r Menu 13 - User Report Codes Press RIGHT arrow key to select this menu.
12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 12345678901234567890123456789012123 14-Wireless Definitions r Menu 14 - Wireless Definitions Press RIGHT arrow key to select this menu.
1234567890123456789012345678901212345 1234567890123456789012345678901212345 1234567890123456789012345678901212345 1234567890123456789012345678901212345 1234567890123456789012345678901212345 1234567890123456789012345678901212345 1234567890123456789012345678901212345 1234567890123456789012345678901212345 1234567890123456789012345678901212345 1234567890123456789012345678901212345 1234567890123456789012345678901212345 123456789012345678901234567890121234 123456789012345678901234567890121234 12345678901234567890
Section 4 - PC Programming and Automation Capabilities 4.1 ELK-RP Software ELK-RP (RP) is a Windows based software package that is compatible with Windows 95 and later. It features an extremely intuitive user interface and contains all data in a central database. RP can be run on a single PC or over a local area network (LAN) with multiple operators. In addition to the traditional security programming features, RP allows you to create and manage the automation functionality in the M1 control.
4.1.2 Check for Conflicts During the connect and disconnect process RP performs an automatic check of the data stored in the control and compares it the database. If there are any conflicts (differences), a pop-up resolution window display them and allows corrections to be made. ELK regards “Check for Conflicts” to be an especially important feature. It can point out any changes that have occurred such as a user having added or changed a code.
4.3 Automation Rules and Attributes The ELK-M1, together with the RP Automation Programming software offers powerful, easy to setup and manage, life style enhancement features. The automation programming allows mixing and matching of lighting components, outputs (relays or voltage), thermostats, temperature sensors, and all the security inputs and features to integrate functions that add value and appeal to the owner/user.
LIGHTING - The M1 can control up to 256 Light (or appliance) devices. Each is assigned to one of 256 addresses. Each devices is displayed in columnar format with the following options and settings: Name - Each device can be given a 16 character name (description) which is displayed on the keypad when the light is being controlled. Format - This pull down box selects the protocol of the device.
VOICE - This section is used to setup and customize many of the 6 word phrases that can be spoken by the control during a certain event or when commanded by an automation rule. The capabilities of this section are quite powerful. The library contains over 500+ words in addition to specialized speech commands for inserting conditions, current time, status/state, time delays, and even an 800hz tone. In addition, any of the 10 custom recordable messages can be included when building these 6 word phrases.
THERMOSTATS - HVAC Thermostats may be read and/or controlled by the M1 and its automation rules engine. This menu allows each thermostat to be assigned a 12 character description for easy reference in an automation rule. The M1 is currently compatible with the following communicating thermostats: RCS, Aprilaire, and HAI. Due to the various data protocols, a Lighting/Thermostat/Serial Interface Expander (ELK-M1XSP) is needed to couple the M1 data bus to HVAC thermostats.
RULES - This section essentially brings all the power of the M1’s automation and its features together. Rules consist of three major elements: A WHENEVER (“triggering”) condition, one or more ANDs (“qualifiers”), and one or more THENs (“activations”). Rules utilize the various elements of the previously described sections in addition to the many control conditions (arm, disarm, alarms, etc.), plus many of the event codes listed in Appendix A.
AND - The second and optional element of a rule is a qualifier. Rules can have one or more qualifiers OR none at all. Even though qualifiers are not required, they are ideal for filtering out actions that should not occur under certain circumstances. A qualifier can be a time, day(s), the state of light or dark, the state of a zone, output, or light, and hundreds of other variables. The state of light or dark can be determined by the Sunrise/Sunset settings from the M1’s Astronomical Clock.
Examples of Rules - Shown below are a series of rules that should help illustrate the power and results that rules can provide. Look closely at the ones that have multiple ANDs and THENs. Rules with Multiple ANDs and THENS work as follows: When the WHENEVER element is triggered, each one of the AND elements is evaluated to determine if the condition its testing is true. If any one of the ANDs are not true, the rule engine stops executing the rule immediately.
Appendix A - Event Codes Event Codes are four digit numbers used to represent alarms, troubles, arm/disarms, restores, and various other conditions that occur within the control. For the most part, they are used only internally by the control’s software. For example: turning on the alarm output. However, there are cases where the installer may need these codes. Case #1 - Keypad F key programming. Each of the Keypad F keys may be programmed to activate a particular condition such as Emergency Panic Alarm.
Appendix A - Event Codes (cont.
Appendix B - Telephone Remote Control There are two methods of entry: 1. Local – Lift house phone off-hook. Enter ***. (To hear over the inside speakers press * 0 * instead.) Once the control hears the pickup sequence it will go offhook and announce a welcome message. It will then prompt the user to enter a valid user passcode. If the User Code is validated the control will announce the main menu selections. These selections are shown below along with the sub menu items for each level.
Appendix B - Telephone Remote Control (cont.) Automation Menu continued For Keypad Temperature - press 5. Certain models of keypads have a built-in temperature sensor. This menu allows you to hear the current temperature of any valid keypad sensor. Upon entry into this menu, any keypad sensor programmed with a name and designated to “Show” by the RP software will be announced by name and number. To choose a keypad sensor, enter it’s two digit number. Add 0’s in front of numbers single digits.
Appendix C - Voice Message Vocabulary Word or Phrase {Blank} = 0 Zero = 21 One = 22 Two = 23 Three = 24 Four = 25 Five = 26 Six = 27 Seven = 28 Eight = 29 Nine = 30 Ten = 31 Eleven = 32 Twelve = 33 Thirteen = 34 Fourteen = 35 Fifteen = 36 Sixteen = 37 Seventeen = 38 Eighteen = 39 Nineteen = 40 Twenty = 41 Thirty = 42 Forty = 43 Fifty = 44 Sixty = 45 Seventy = 46 Eighty = 47 Ninety = 48 Hundred = 49 Thousand = 50 [200ms Silence] = 51 [500ms Silence] = 52 [800hz Tone] = 53 A A = 54 Access = 55 Acknowledged =
Appendix C - Voice Message Vocabulary (cont.
Appendix D - Two Way “Listen-in/Talk” Interface (optional) Using a Two Way Interface board (ELK-M1TWI), the M1 accommodates up to 3 zones of listen-in. Each zone can have up to 4 microphones for a total of 12 listen-in points. Talk back is delivered through the speakers connected to Output 1. A two way session can be triggered by any number of zones when an alarm occurs. Two way can also be triggered during a Telephone Remote Control session. Instructions for the ELK-M1TWI are included with the interface.
Appendix E - SIA CP-01 Compliance The ELK-M1 complies with the SIA CP-01 Control Panel Standard - Features for False Alarm Reduction PROGRAMMABLE FEATURES, SHIPPING DEFAULTS, AND RECOMMENDED PROGRAMMING FEATURE CP-01 Std. Par. # REQUIREMENT ALLOWABLE RANGE / PURPOSE RECOMMENDED PROGRAMMING * SHIPPING DEFAULT Exit Delay Time 1 & Exit Delay Time 2 4.2.2.1 Required (programmable) 45 - 120 sec.
Appendix F - Regulatory Agency Statements The ELK-M1 complies with Part 68 of the FCC rules. On the front nameplate of the main control board is a label that contains, among other information, the FCC certification number and ringer equivalence number (REN) for this equipment. If requested, this information must be provided to the telephone company. This equipment uses an RJ31X jack to connect to the telephone network.
[Intentionally left blank] M1 Installation and Programming Manual Page 67
Appendix G - Additional Keypad Information Detail A Bend (arch) the 5 wires from the M1PR wiring plug as shown. This provides space between the plug and the connector (J2) so that they may be attached. ELK-M1KP LCD Keypad M1PR Wiring Plug Back (Circuit) Side of Keypad J1 J2 ELK-M1PR Six (6) conductor plug-in data bus cable (4 wires got to the M1 Control, 1 is a zone input and 1 is a programmable output).
Appendix G - Additional Keypad Information (cont.) KEYPAD INTERNAL TEMPERATURE SENSOR Every standard ELK-M1KP has a built-in temperature sensor, which detects the surrounding ambient temperature. The sensor temperature may be displayed on the LCD, and read from another keypad or the telephone remote control. It may also be used with the Elk-RP Whenever/And/Then Rules to automatically cause an action or control something. i.e., a fan, pump, light, etc. Viewing a Keypad temperature sensor reading 1.
M1 LIMITED WARRANTY The ELK-M1 and its associated component products are warranted by Elk Products, Inc. (“Manufacturer”) against defects in material and workmanship for a period of two (2) years from the date of manufacture. If product is found to be defective during the first 180 days, manufacturer may allow an over the counter exchange, subject to inspection and approval by one of it’s representatives.
Index A I Rules 55 Alarm Abort 40 Alarm Cutoff Timers 33 Anti-Takeover 21 Area Partitioning 21 Area Reporting Codes 40, 41 Auto Stay Option 27 Automation control function 16 Automation Tasks 51 Auxiliary Power Connections 10 Input/Output Expander Addresses 24 Installation and Wiring 8 Installer Program Code 14, 16, 22, 25 S B Battery Connection 10 Bus Module Enrollment 25 C Central Station alarm verification 36 Communicator Setup Checklist 22 Comparisons of M1 and M1G (Gold) 5 Counters 53 CrossZonePo
www.elkproducts.
