Installation Manual

ManualsBrandsELK ManualsAccess Controls1 door access module

Page 1

Single Door Access Module ELK-M1KAM

FEATURES:

z Input for a 26 bit Wiegand Reader

z Input for a Dallas "One-Wire" iButton Reader

z Heavy Duty Form "C" Relay Contacts for Switching Door Strike Power

z Low Current (50mA) Switched Negative (pull to ground) Output for Door Held Open Alarm

z Low Current (10mA) Switched Negative (pull to ground) Output for System Ready To Arm indication

z Low Current (10mA) Switched Negative (pull to ground) Output for System Armed indication

z Supervised Input for RTE (Request To Exit) Button/Device

z Supervised Input for Door Status Sensor

z Installs in place of an M1 Keypad and operates from the RS-485 4-Wire Keypad Data Bus

z Four selectable Time settings for "Request to Exit" and "Door Held Open"

z Hardware Watchdog Circuit

SPECIFICATIONS:

z Connections: Unpluggable Screw Terminals, 16 Position

z Operating Voltage: 13.8 VDC

z Current Draw: Less than 30 mA with min. activity, 44 mA fully active

z Housing Dimensions: 4.25" x 6.375" x 2.125"

z Circuit Board Dimensions: 3.95" W x 2.875" H x .95" D

Features and Specifications subject to change without notice.

L610 06/28/13

APPLICATION

The M1KAM is a single door access interface for use with the M1 Control

Panel family. It connects to the 4 wire keypad data bus and takes the

place of a traditional M1 Keypad. The maximum number of Keypads

(combination of M1KAMs and Keypads) that may be connected to an

M1 is 16. It is important to note that while an M1KP or M1KP2 keypad

can accept a 26 bit access reader, the M1KAM is a more powerful and

less expensive door interface solution. It includes a local relay output

with form "C" dry contacts for compatiblity with most all door locking

devices. It works with card swipe or proximity readers conforming to

the 26 bit wiegand format, but can also accept a Dallas "One-Wire"

iButton reader/device. Like the M1KP and KP2 Keypads, the M1KAM

has 1 input and 1 output correlating to its bus address. The input

reports back the local door status to M1, and the output is used by M1

to control the lock relay. Locally, the M1KAM has additional input/

outputs consisting of a RTE (request to exit) input, a DHO (door held

open) voltage output, and voltage outputs representing the M1 Ready

To Arm and System Armed status. These outputs are switched

negative (pull to ground). The M1KAM is mounted in a universal surface

mount plastic housing with knockouts for surface mount raceways.

PO Box 100 • Hildebran, NC 28637 USA • 828-397-4200 Voice • 828-397-4415 Fax

http://www.elkproducts.com • email: info@elkproducts.com

Summary of content (6 pages)

PAGE 1
Single Door Access Module ELK-M1KAM APPLICATION The M1KAM is a single door access interface for use with the M1 Control Panel family. It connects to the 4 wire keypad data bus and takes the place of a traditional M1 Keypad. The maximum number of Keypads (combination of M1KAMs and Keypads) that may be connected to an M1 is 16. It is important to note that while an M1KP or M1KP2 keypad can accept a 26 bit access reader, the M1KAM is a more powerful and less expensive door interface solution.
PAGE 2
INSTALLATION Mount the M1KAM within 25ft of the door being controlled. Since It connects to the 4-wire keypad data bus the M1KAM can be located from the control up to the maximum distance of the data bus. The ambient temperature range should be between 32° and 120° F (0° to +49° C). CAT5 or CAT6 wire (4 pair, 8 conductor) is recommended for all data bus cables as the spare wires may be required for data return paths where multiple homeruns or devices are installed.
PAGE 3
VERY IMPORTANT: EOL terminating resistors MUST be installed on inputs IN1 Rte (Request to exit) and IN2 Dr (Door Sw. Input). The M1KAM will not work properly if these inputs are left open. If an RTE (request to exit) device or a Door Switch is not being installed then simply install the EOL resistor across the input terminals as shown below. DOOR TIME ELK-M1KAM Single Door Access Module ADDRESS 1 2 4 8 Switch 2 shown in the UP position, all others are down. This selects Address 2.
PAGE 4
Setting the Data Bus Address and Enrolling Device(s) into the System All devices that operate on the RS-485 4-wire data bus must have a unique address setting from 1 to 16 within their device TYPE. Keypads and Access Modules are device TYPE 1, input (zone) expanders TYPE 2, output expanders TYPE 3, etc. The purpose of device types is so that the address numbers can be re-used in each different device type.
PAGE 5
Programming the Control Panel "Keypad" Options The ELK-M1KAM takes the place of a regular M1 Keypad. Although a Keypad has multiple programming attributes, there are only two (2) attributes that are required to be programmed for the Elk-M1KAM. The other attributes can remain blank or as-is. 1) Program a NAME: A 16 digit description for describing the location of the Elk-M1KAM. i.e., employee entry 2) Program the AREA: This is very important! It defines which area (partition) the Elk-M1KAM belongs to.
PAGE 6
NOTE: M1KP Keypads require either a plug-in Elk-M1PR Wiegand Reader or a external 26bit Wiegand Reader (Elk-106055 or compatible) connected via a separately purchased Elk-W035A cable/wiring harness. M1KP2 and M1KP3 Keypads only accept external readers connected via a separately purchased Elk-W039A cable/wiring harness. 1. 2. 3. 4. 5. The Keypad with the attached reader must be enrolled and operational on the M1 or M1EZ8 Control.