Use and Care Manual

ManualsBrandsElkay ManualsKitchenWaterSentry VII Replacement Filter for Coolers and Fountains

97747C (Rev. J - 5/13)Page 1

WaterSentry

Water Cooler.

7. Turn on water supply and hold open the bubbler on

cooler until approximately 1 gallon of water is dis-

pensed. This flushing procedure purges air and fine

carbon particles from the filter. When 1 gallon of water

has been purged through the cooler, carefully inspect all

water connections for leaks.

LK2156 Dispensing Valve with or without a chiller tank,

LK1141A Bubbler with or without a chiller unit, under

sink application.

1. Open inlet water supply valve, open dispensing valve

or bubbler and allow approximately 1 gallon of water to

be dispensed. This flushing procedure purges air and

fine carbon particles from the filter.

2. Turn dispensing valve off and carefully inspect all water

connections for leaks.

3. Unit is now ready for operation.

These filter kits are designed to be used with the following

Elkay products.

1. Water Coolers: LZ, LISEA, LIEA, LFDE, LFAE, LWAE,

and LWCE.

2. LK2156 Dispensing Valve with or without a chiller unit.

3. LK1141A Bubbler with or without a chiller unit.

4. Independently in an undersink application. For

undersink applications, it is recommended that water

be dispensed through a dedicated valve or faucet

instead of the sink faucet due to the reduced flow

through the filter.

NOTICE: Do not use with water that is microbiologically

unsafe or of unknown quality without adequate

disinfection before or after the system.

General Installation Instructions

1. These filter kits must be installed in compliance with all

state and local laws and regulations governing the

installation and use of this product. Maximum inlet

water temperature 100°F (38°C).

2. Mount filter head in a suitable location, using the filter

mounting bracket and screws supplied. Allow enough

room under the filter head for installation and removal of

filter cartridge (13" minimum).

3. Connect the cold water supply to the filter through a

shut-off valve and 3/8" O.D. tubing (supplied by the

installer). For ease of servicing, the shut-off valve

should be located within easy reach of the filter.

NOTE: The inlet and outlet fitting supplied as

part of the filter head are John Guest Superseal

fittings that accept 3/8" O.D. tubing on the filter

inlet and 1/4" O.D. tubing on the outlet. They may

be used with copper, stainless steel, or semirigid

nylon or polypropylene tubing, with a rated working

pressure equal or greater than encountered in

application. Do not use soft or braided tubing.

4. CAUTION: If supply pressure will ever exceed

100 psi, install a pressure regulator to limit the

inlet pressure to the filter to 100 psi or below.

DO NOT ATTACH HOT WATER LINE TO FILTER.

To make connections on the filter head, loosen locknut.

Push the tube end past both o-rings to a positive stop in

the filter head recess - approx. 1", locknut may have to

be backed out a little more. Screw the locknut hand tight

to seal (See Fig. 1). Ends of tubing must be cut square

and free of burrs and sharp ends that could cut or nick

the o-rings.

5. Connect the outlet of the filter to the inlet of the union

using the 1/4" O.D. poly tubing and 1/4" union supplied.

6. Remove filter from carton, remove protective cap, attach

filter to filter head by firmly inserting into head and

rotating filter clockwise.

FIG. 2

FIG. 1

See Note 4: Screw the locknut hand tight to seal

Filter Replacement*

1.Turn inlet water valve off.

2.Open bubbler to relieve pressure build-up in the system.

3.Remove filter from head by rotating filter counterclock

wise.

4.Remove new filter from carton, remove protective cap;

cap may be placed on old filter to reduce the chance of

water spilling from filter housing.

5.Attach filter to filter head by firmly inserting into head

and rotating filter clockwise.

*Optional Filter Monitor (Part No. 98262C)

Counts gallon usage and provides an audible alert

when filter needs replacement. Alert is sounded only

when water is being dispensed; beeping is not continuous.

Requires 2 AA alkaline batteries.

FILTER KIT

EWF172 Watersentry

VII KIT

(Lead, Aesthetic Chlorine Taste & Odor & Particulate Class I Reduction)

FOR COMMERCIAL USE ONLY

The Elkay

WaterSentry

VII is certified by WQA to NSF/ANSI Standard 42 and 53 for the

reduction of Aesthetic Chlorine, Taste and Odor, Particulate Class I, and Lead, as verified and

substantiated by test data.

Summary of content (5 pages)

PAGE 1
FILTER KIT EWF172 Watersentry® VII KIT (Lead, Aesthetic Chlorine Taste & Odor & Particulate Class I Reduction) FOR COMMERCIAL USE ONLY The Elkay® WaterSentry® VII is certified by WQA to NSF/ANSI Standard 42 and 53 for the reduction of Aesthetic Chlorine, Taste and Odor, Particulate Class I, and Lead, as verified and substantiated by test data. ® These filter kits are designed to be used with the following Elkay products. 1. Water Coolers: LZ, LISEA, LIEA, LFDE, LFAE, LWAE, and LWCE. 2.
PAGE 2
NOTE: The filter head contains an automatic shut-off valve that stops the flow of water, if the filter is removed inadvertently without shutting off the incoming water. RATED OPERATING CONDITIONS 105 PSI (7.4 Kg/cm2) 20 PSI (1.4 Kg/cm2) 1.5 GPM (5.7 LPM) 1,500 Gallons (5,679 L) 120° F (50° C) 40° F (5° C) Pressure (Max.) Pressure (Min.) Flow Rate Rated Capacity Temperature (Max.) Temperature (Min.) NOTE: Performance will vary depending on local water conditions.
PAGE 3
FILTER LOCATION LIEATL* FILTER LOCATION LISEA* LIEA* LFAE* LFDE* LWAE* LWCE* FILTER LOCATION FILTER LOCATION Page 3 97747C (Rev.
PAGE 4
LK2156 & REMOTE CHILLER (Alternate LK2156 alone) WATER "IN" TO REMOTE CHILLER 1/4" (6mm) UNION (SUPPLIED) 1/4" (6mm) O.D. TUBING (SUPPLIED) FROM COLD WATER SUPPLY O.D. TUBE 3/8" (10 mm) INSTALLATION WHEN USED WITH WATER CHILLER PLUMB FILTER OUTLET DIRECTLY TO LK2156 IF NO CHILLER IS USED See page 5 for replacement information. 97747C (Rev.
PAGE 5
NOTICE To receive maximum benefit from your ELKAY WaterSentry® filters, note the installation dates below and change according to the following guidelines. ELKAY Part No. 51299C WaterSentry® VII -- Lead Reduction Filter Change every 1,500 gallons, or once a year -- whichever occurs first. -- KEEP THIS SHEET IN A HANDY LOCATION -DATE INSTALLED MODEL (TYPE OF FILTER) SERVICE PERSON DATE INSTALLED MODEL (TYPE OF FILTER) SERVICE PERSON FOR PARTS, CONTACT YOUR LOCAL DISTRIBUTOR OR CALL 1.800.323.