Specification Sheet

GENERAL
Sink is formed of #18 (1.2mm) gauge, 300 series nickel bearing
stainless steel. Undermount.
DESIGN FEATURES
Bowl Depth: 8" (203mm) small bowl,10" (254mm) large bowl.
Underside: Sound dampening pads with spray undercoating to
dampen sound and reduce condensation.
Finish: Exposed surfaces are polished to a Radiant Satin finish.
OTHER
Drain Openings: 3-1/2" (89mm).
NOTE: All Dayton undermount sinks are designed to affix easily
to the underside of any solid surface countertop.
OPTIONAL ACCESSORIES
Bottom Grid: GBG1415SS (small bowl), GBG1318SS (large bowl)
Drain: D1125
Cutting Boards: CB1516 (smallbowl), CBR1316 (largebowl) (sink
must be installed with a 1/2” reveal for cutting board to fit properly)
Rinsing Baskets: LKWRB1316SS (smallbowl), LKWRB1318SS
(largebowl), LKWERBSS (either bowl)
Utensil Caddy: LKWUCSS
Mounting Clip: LKUCLIP8 (2 packages required)
Template: 64180279
Model DXUH312010R
Model DXUH312010L
Elkay
elkaypro.com
2222 Camden Court
Oak Brook, IL 60523
©2013 Elkay
(Rev. 12/13)
2-59F
In keeping with our policy of continuing product improvement, Elkay reserves the right to change
product specific ations without notice. Please visit elkayusa.com for most current version of Elkay
product specification sheets.
This specification describes an Elkay product with design, quality and functional benefits to the
user. When making a comparison of other produc ers’ offerings, be certain these featu
res are not
overlooked.
Dayton
®
Undermount Double Bowl Sink
Model DXUH312010 Series
S P E C I F I C AT I O N S
SINK KIT
FAUCET FEATURES
LK1501CR
- Chrome finished, single-lever kitchen faucet with side spray.
- Flexible supply tubes with 1/2" (13mm) male IPS adapters.
- Two 1 3/8“ diameter faucet holes required.
LK5000CR
- Chrome finished, single-lever kitchen faucet with pull-down spray.
- Braided stainless steel supply lines.
- Three 1 3/8“ diameter faucet holes required.
Max counter thickness: 2.5” (63mm).
Faucets comply with: ADA, ANSI/NSF61, ASME A112.18.1/CSA B125.1,
cUPC, CA AB1953
Faucet flow rate: 1.5 GPM/5.7 L/min at 60 P.S.I.G.
DXUH312010LDF includes: (1) Sink - DXUH312010L, (1) Faucet - LK1501CR,
and (2) Drains.
DXUH312010RDF includes: (1) Sink - DXUH312010R, (1) Faucet - LK1501CR,
and (2) Drains.
DXUH312010LDFBG includes: (1) Sink - DXUH312010L, (1) Faucet - LK5000CR,
(1) Bottom Grid - GBG1318SS, and (2) Drains.
DXUH312010RDFBG includes: (1) Sink - DXUH312010R, (1) Faucet - LK5000CR,
(1) Bottom Grid - GBG1318SS, and (2) Drains.
DRAIN FEATURES
Stainless steel body and strainer.
Fits 3-1/2” (89mm) opening.
BOTTOM GRID FEATURES
Nickel-bearing stainless steel
Bright finish
LK5000CR
LK1501CR
GBG1318SS
C
Sinks are listed by IAPMO as meeting the applicable
requirements of the Uniform Plumbing Code , International
Plumbing Code , and National Plumbing Code of Canada.
Sink complies with ASME A112.19.3/ CSA B45.4