Installation Sheet

ManualsBrandsElkay ManualsDrinking FountainsElkay Vandal Resistant Retrofit Water Filtration Kit - Includes WaterSentry VII Filter, Mounting Box, and Filter Status Monitor

Page 1 1000003634 (Rev. A - 03/17)

IMPORTANT NOTE – To avoid danger of an electric shock hazard, disconnect

power to your unit before installing the lter.

1500 Gallon Vandal-Resistant Retro-Fit Filter Kit with Filter Monitor

Fig. 1

Installation Manual

EF1500VRBMC

IMPORTANT

THIS IS AN INDOOR APPLICATION ONLY.

ALL SERVICE TO BE PERFORMED BY AN

AUTHORIZED SERVICE PERSON.

TOOLS REQUIRED

BUT NOT PROVIDED:

- SAFETY GLASSES

- GLOVES

- LEVEL

- PENCIL

- MOUNTING SCREWS, ANCHORS, FASTENERS

INSTALLATION STEPS

1. Before starting your installation, verify that

you have the following included pieces.

a. 1 Pinned Torx Bit

b. 2 AA Batteries

c. 1 Pinned Torx Screw

d. 3.5 Feet of Poly Tubing

2. Find a location to mount your new lter

box near the water dispenser to which it is

being connected. For accurate monitoring,

the lter box should be mounted vertically

as shown (Fig. 2, page 2).

3. Shut off the water and electricity to the

water dispenser.

4. Lift the cover at the bottom and slide

upwards toward the top.

Summary of content (8 pages)

PAGE 1
Installation Manual EF1500VRBMC 1500 Gallon Vandal-Resistant Retro-Fit Filter Kit with Filter Monitor IMPORTANT NOTE – To avoid danger of an electric shock hazard, disconnect power to your unit before installing the filter. IMPORTANT THIS IS AN INDOOR APPLICATION ONLY. ALL SERVICE TO BE PERFORMED BY AN AUTHORIZED SERVICE PERSON. TOOLS REQUIRED BUT NOT PROVIDED: - SAFETY GLASSES - GLOVES - LEVEL - PENCIL - MOUNTING SCREWS, ANCHORS, FASTENERS INSTALLATION STEPS 1.
PAGE 2
5. Take the filter box and place on the wall in the desired location. Be sure that the box is positioned vertically on the wall as shown. The arrow on the water monitor valve should always be pointing UP (Fig. 4). Make sure the filter box is level, take a pencil and mark around the inside opening and the mounting locations. If the water will not be coming thru the wall into the back of the filter box, knock-outs have been provided to allow the water lines to run thru the sides or bottom.
PAGE 3
6. Cut a hole in the wall anywhere inside the marked location to allow room for the water lines to come into the back of the box. 7. Remove any protective covering from the outside of the filter box. Fig. 5 8. Using the appropriate fasteners (Not Supplied), mount the box to the wall. Fig. 6 Page 3 1000003634 (Rev.
PAGE 4
9. Disconnect the water inlet from the water dispenser and connect to the inlet copper tube on the filter head. Inlet not included included Inlet Fitting fitting not Fig. 7 10. Connect the poly tubing from inlet of the water dispenser to the outlet fitting on the flow meter Fig. 8 1000003634 (Rev.
PAGE 5
11. Remove the red cap from the filter and install on the filter head turning clockwise. Fig. 9 Page 5 1000003634 (Rev.
PAGE 6
12. Remove the filter monitor from the back of the box and insert the supplied batteries. Once installed, the monitor will light up. The monitor can now be put back on the back of the box. Make sure it is positioned so that it can be viewed thru the window in the front cover once it is installed. Fig. 10 13. Turn on the water and check for leaks. Repair as needed 14. Run approximately 1 gallon of water thru the fixture. This flushing procedure purges air and fine carbon particles from the filter.
PAGE 7
15. After peeling the protective covering from the front cover, hook the tabs on the top into the slots on the top of the box. Slide the cover down and install the supplied screw. Once done keep the bit as it will be needed for replacing the filter. Fig. 11 Fig. 12 OPERATING INSTRUCTIONS FOR THE FILTER MONITOR 1. The filter monitor backlight automatically turns on when there is water flowing through it.
PAGE 8
NOTICE To receive maximum benefit from your ELKAY WaterSentry® filters, note the installation dates below and change according to the following guidelines. ELKAY Part No. 51299C WaterSentry® VII -- Lead Reduction Filter Change every 1,500 gallons, or once a year -- whichever occurs first. -- KEEP THIS SHEET IN A HANDY LOCATION -DATE INSTALLED MODEL (TYPE OF FILTER) SERVICE PERSON DATE INSTALLED MODEL (TYPE OF FILTER) FOR REPLACEMENT FILTER, PLEASE CALL 1.800.834.