Installation Guide

ManualsBrandsElkay ManualsDrop-in Kitchen SinksQuartz Classic Dual Mount Composite 16.63 in. Single Bowl Kitchen Sink in Bisque

• READ THESE INSTRUCTIONS THOROUGHLY BEFORE YOU BEGIN.

• Follow all local plumbing and building codes.

• Before installation, please inspect the sink for damage. Do not install a damaged sink.

• For drop-in sinks proceed to section I. For undermount sinks proceed to section II.

I. DROP-IN INSTALLATION

Note: The clips provided are designed for a maximum counter-

top thickness of 1-3/4”.

1. To determine the proper size opening for your sink place

the sink upside down on top of the countertop. Mark or trace

line around the edge of the rim. Then cut an opening 5/16”

inside the line. (See illustration A).

2. Set new sink in opening to see that it fits properly.

3. Faucet Holes: Faucet holes can be identified by the faucet

hole emboss on the underside of the faucet deck and the

corresponding circular labels located on the faucet deck top

surface. Before punching the holes please verify that the

circular labels are properly centered over the faucet hole

emboss. The faucet hole should be carefully penetrated

from above the sink using a chisel or screw driver and

tapping lightly on the circular labels. (See illustration B). If

necessary the hole can been enlarged using a metal hole

saw, a jigsaw with a metal cutting blade or a metal file.

Note: MUST SUPPORT FAUCET DECK ON BOTH SIDES

WHILE PUNCHING FAUCET HOLES.

4. Attach faucet, drain fittings and accessories according to the

manufacturer’s instructions.

5. As shown in illustration C and D, align clips with the corre-

sponding slots in the sinks per illustration C. It may be

necessary to use a mallet and wood block to push it into

place, as shown in illustration D. Make sure metal portion of

the clip (clamp) is in the open position so that sink can be

dropped into cutout.

6. Apply a bead of a high quality silicone adhesive caulk to the

underside of the sink rim and position sink into countertop

opening. CAUTION: Use only a high quality silicone

adhesive caulk.

7. Swing metal portion of clip (clamp) into the clip base. (See

illustration E). Using a Phillips screw driver, turn screw until

clamp engages the countertop. Use shims if necessary.

8. Remove excess caulk and allow caulk to cure following the

caulk manufacturer’s instructions.

E-Granite

™

Sink

Installation Instructions

ILLUSTRATION A

ILLUSTRATION B

TRACE COMPLETELY

AROUND EDGE OF SINK

DRAW SECOND

LINE INSIDE SINK

OUTLINE (CUT LINE)

5/16"

TO BE REMOVED FOR USE BY THE OCCUPANT!

CLIP BASE

OPEN

CLAMP

SLOT

SILICONE CAULK

(NOT INCLUDED)

CLOSED

CLAMP

ILLUSTRATION C ILLUSTRATION D ILLUSTRATION E

Summary of content (3 pages)

PAGE 1
TO BE REMOVED FOR USE BY THE OCCUPANT! Installation Instructions E-Granite™ Sink • READ THESE INSTRUCTIONS THOROUGHLY BEFORE YOU BEGIN. • Follow all local plumbing and building codes. • Before installation, please inspect the sink for damage. Do not install a damaged sink. • For drop-in sinks proceed to section I. For undermount sinks proceed to section II. I. DROP-IN INSTALLATION Note: The clips provided are designed for a maximum countertop thickness of 1-3/4”. 1.
PAGE 2
Installation Instructions I I . UNDERMOUNT INSTALLATION ATTENTION INSTALLER: • ELKAY RECOMMENDS THAT UNDERMOUNT SINKS SHOULD BE INSTALLED BY A PROFESSIONAL EXPERIENCED INSTALLER. • WARNING: THE ENCLOSED CUTOUT TEMPLATE PROVIDES A SINK OPENING THAT WILL EXPOSE APPROXIMATELY 1/8" OF SINK RIM LEDGE AS SHOWN IN ILLUSTRATION F. • IT IS RECOMMENDED THAT YOU DISCUSS THIS WITH YOUR CUSTOMER AND AGREE TO WHAT THE FINISHED EFFECT WILL BE. ELKAY IS NOT RESPONSIBLE FOR IMPROPER SINK OR COUNTERTOP INSTALLATIONS.
PAGE 3
Installation Instructions ELKAY LIMITED LIFETIME E-GRANITE SINK WARRANTY Elkay warrants to the original purchaser of an Elkay E-Granite sink that Elkay will, at its option, replace or repair, without charge, such product if it fails due to a manufacturing defect for a lifetime of normal residential use. Product replacement does not include transportation cost or labor installation cost.