Installation Sheet

ManualsBrandsElkay ManualsPopular CollectionsElkay EZH20 17-7/8" Wall Mounted Bottle Filler

1000002042 (Rev.D-09/15)

EMASMB*A & LMASMB*A

Page 1

EMASMB & LMASMB Surface Mount Bottle Filling Stations

To assure you install this model easily and correctly,

PLEASE READ THESE SIMPLE INSTRUCTIONS BEFORE STARTING

THE INSTALLATION. CHECK YOUR INSTALLATION FOR COMPLIANCE

WITH ALL PLUMBING, ELECTRICAL AND OTHER APPLICABLE CODES.

F O L L O W A L L WARNINGS AND CAUTIONS CAREFULLY.

After

installation, leave these instructions with the customer for future reference.

IMPORTANT

FOR INDOOR USE ONLY!

ALL SERVICE TO BE PERFORMED BY AN

AUTHORIZED SERVICE PERSONNEL.

RATED FOR COMMERCIAL USE ONLY

Installer

TOOLS/ITEMS REQUIRED

BUT NOT SUPPLIED

- SERVICE STOP VALVE WITH 3/8"

COMPRESSION OUTLET

- FASTENERS FOR WALL TYPE (5 REQ’D.)

- SLIP JOINT DRAIN UNION OR

COMPRESSION CLAMP

- 5/32" HEX-WRENCH

Warnings

1. Use with clean, clear, fresh potable drinking water only! Do not use with water that is microbiologically

unsafe or of unknown quality without adequate disinfection before the system.

2. These products are designed to operate on 20 to 105 psig (0.14-0.72 MPa) supply line pressure and a

maximum water temperature of 90°F (32°C). If inlet pressure is above 105 psig (0.72 MPa), a pressure

regulator must be installed in supply line. Any damage caused by reason of connecting this product to

supply line pressure lower than 20 psig or higher than105psig is not covered by warranty.

INSTALLATION, CARE & USE MANUAL

This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or

mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use

of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning

and user maintenance shall not be made by children without supervision.

Original Instructions

Summary of content (6 pages)

PAGE 1
EMASMB*A & LMASMB*A INSTALLATION, CARE & USE MANUAL Original Instructions EMASMB & LMASMB Surface Mount Bottle Filling Stations IMPORTANT FOR INDOOR USE ONLY! ALL SERVICE TO BE PERFORMED BY AN AUTHORIZED SERVICE PERSONNEL. RATED FOR COMMERCIAL USE ONLY TOOLS/ITEMS REQUIRED BUT NOT SUPPLIED - SERVICE STOP VALVE WITH 3/8" COMPRESSION OUTLET - FASTENERS FOR WALL TYPE (5 REQ’D.
PAGE 2
EMASMB*A & LMASMB*A ROUGH-IN EMASMB & LMASMB ADA STAND ALONE MOUNTING STAND ALONE MOUNTING IMPORTANT! INSTALLATION NOTES: • Ensure wall is structurally sound to bear the loads imparted by the Surface Mount Bottle Filler. • Ambient air temperature limits: 10°C - 38°C (50°F - 100.4°F). Climate Class SN-ST. • Not suitable for installation in areas where water jets could be used. 7/16 X 3/4 11mm X 19mm OBROUND MOUNTING HOLE (6) "C" 7 178mm ‰ 7 178mm 22 559mm 3/8" 9.
PAGE 3
EMASMB*A & LMASMB*A ROUGH-IN EMASMB & LMASMB ADA ABOVE COOLER MOUNTING STAND ALONE MOUNTING IMPORTANT! INSTALLATION NOTES: • Ensure wall is structurally sound to bear the loads imparted by the Surface Mount Bottle Filler. • Ambient air temperature limits: 10°C - 38°C (50°F - 100.4°F). Climate Class SN-ST. • Not suitable for installation in areas where water jets could be used.
PAGE 4
EMASMB*A & LMASMB*A INSTALLATION INSTRUCTIONS EMASMB UNIT SHOWN TOP SCREWS TOP COVER BACK PANEL OUTER WRAPPER REGULATOR ASSEMBLY BATTERY TRAY PLUMBING DIAGRAM NON-FILTERED INSTALLER TO SUPPLY: SHUT OFF VALVE BOTTOM COVER BOTTOM SCREWS REAR VIEW Wall Mounting (reference Rough-Ins, Fig. 1 and Fig. 2) 1. Remove Top Cover from Bottle Filler by removing two (2) screws from bottom of unit. Use a 5/32" hex wrench (not supplied). 2.
PAGE 5
EMASMB*A & LMASMB*A Instruction for Use 1. Place container under the dispenser nozzle and depress the actuator button. Hold until container is filled to the level desired. 2. To stop water flow, release actuator button. Pull container away from dispenser nozzle. Installing/Replacing Batteries: 1. Remove Bottom Cover from Bottle Filler by removing two (2) screws from bottom of unit. Use a 5/32" hex wrench (not supplied). The battery tray is located on the bottom cover.
PAGE 6
EMASMB*A & LMASMB*A SETTING THE CONTROL BOARD VERIFY CONTROL BOARD SOFTWARE 1) To verify the software program of the control board the unit will need to be shut down and restarted. The chiller (if present) does not need to be shut down and restarted. 2) Shut down the unit by removing a battery. 3) Restart the unit by installing the batteries 4) Upon start up the bottle count display will show the software designation of 'ELKAY BC'.