Specification Sheet

ManualsBrandsElkay ManualsDrinking FountainsElkay 7.6 GPH Wall Mount Bi-Level Deluxe Cooler with Prepped Glass Filler

In keeping with our policy of continuing product improvement, Elkay reserves the right to change

product specifications without notice.

This specification describes an Elkay product with design, quality and functional benefits to the

user. When making a comparison of other producers’ offerings, be certain these features are not

overlooked.

GENERAL

Self-contained, electric refrigerated, wall hung water cooler.

Capacity of 50°F drinking water based upon 80°F inlet water

and 90°F ambient.

NOTE: Minimum 40 psi supply line pressure required in special

circumstances where both sides of bi-level are in use simulta-

neously to ensure adequate stream height. Does not apply to

non-refrigerated units.

NO LEAD DESIGN

THIS WATER COOLER COMPLIES WITH THE LEAD-FREE

DEFINITION IN THE SAFE DRINKING WATER ACT OF 1986

AND LEAD CONTAMINATION CONTROL ACT OF 1988.

Elkay Water Coolers are manufactured with a waterway

system utilizing copper components and completely lead-free

material. These waterways have no lead because all lead

materials, such as leaded brass, have been removed. All joints

are brazed using silver solder only. No lead solder is permitted.

A strainer with an easily cleanable screen is provided to allow

trapping and convenient removal of water born particulate of

140 microns and larger prior to their entry into the water cooler.

EWTLA8K and EWTLA14K are certified to NSF/ANSI 61.

EWTLA16K meets only the lead-free definition of NSF/ANSI 61.

COOLING SYSTEM

Motor Compressor: Hermetically sealed, 115 Volt, 60 Hertz

single phase. Sealed-in lifetime oil supply. Equipped with elec-

tric cord and three prong molded rubber plug.

Condenser: Fan cooled, copper tube with aluminum fins. Fan

motor is permanently lubricated.

Cooling Unit: Combination tube-tank type. Tube portion is

continuous coil of copper tubing. Fully insulated with EPS foam

which meets Underwriters Laboratories Inc. requirements for

self-extinguishing plastic material.

Refrigerant Control: Refrigerant HFC-134a is controlled by

accurately calibrated capillary tube for positively trouble-free

performance.

Temperature Control: Enclosed adjustable thermostat is

factory preset. Requires no adjustment other than for

altitude requirements.

CONSTRUCTION

Fountain Top: One piece stainless steel top, polished to a uni-

form Elkay bright luster finish. Exclusive Cascade basin, tested

most splash-resistant, features multi-level deck design with a

built-in vandal-resistant strainer.

Exclusive Flexi-Guard

Safety Bubbler**: Innovative design

utilizes a pliable polyester elastomer to prevent accidental

mouth injuries. Flexes on impact, then returns to original posi-

tion. Strong. Abrasion-resistant. Anti-sweat. Meets UL require-

ments and all sanitary codes.

Removable Panel: Removable front panel offers easy accessi-

bility to interior. Cabinet design allows for flush to wall mounting.

Color Selection: Light Gray Granite is furnished as standard

unless alternate wrapper color is selected. Alternate wrapper

colors in vinyl are: Sandalwood and Natural Almond. All fur-

nished at no extra cost. Stainless Steel units available at extra

cost.

5 YEAR LIMITED WARRANTY on the refrigeration system of

the unit. Electrical components and water system are

warranted for 12 months from date of installation. Sample

Certificate available on request.

Elkay Pressure-Type Water Coolers are designed to operate on

20 psi to 105 psi supply line pressure. If inlet pressure is above

105 psi, a pressure regulator must be installed in the supply

line. Any damage caused by reason of connecting this product

to supply line pressures lower than 20 psi or higher than 105

psi is not covered by the warranty.

STANDARDS

Model EWTLA8K

** Patent #4,481,971

No Lead Two-Level

Wall Mount Water Cooler

Models EWTLA8K, EWTLA14K and EWTLA16K

SPECIFICATIONS

Elkay

2222 Camden Court

Oak Brook, IL 60523

Printed in U.S.A.

(Rev. 1/06) 11-2F

elkayusa.com

Elkay Electric Air Cooled Water Coolers meet the

requirements of NSF/ANSI 61. Unit complies with

A.R.I. Standard 1010.

CAPACITIES CHART

*Based on 80°F inlet water temperature. •Pre-cooler capacities based on 60%

spill through pre-cooler.

†Glass filler available at extra cost. Requires factory preparation to receive glass

filler. Upper unit only.

Rated watts shown are based on operational (run) time, in compliance with A.R.I.

Standard 1010 conditions. Specific applications will determine the actual watts

consumed per hour. Watts consumed will be based on number of people served

per hour (usage), ambient temperatures, and inlet water temperature.

*GPH of 50°F Drinking Water

Full Glass† Ship.

Model Base

Room Temperature °F

Rated Load Filler •Pre- Wt.

Number Rate 70°F 80°F 90°F 100°F Watts Amps Option Cooler Lbs.

EWTLA8K 7.6 9.2 8.7 8.0 7.4 370 4.0 Yes No 108

EWTLA14K 13.5 15.5 14.6 13.5 12.4 665 7.2 Yes No 112

EWTLA16K 15.5 17.8 16.8 15.5 14.3 510 5.5 Yes Yes 112

Summary of content (2 pages)

PAGE 1
No Lead Two-Level Wall Mount Water Cooler Models EWTLA8K, EWTLA14K and EWTLA16K ® SPECIFICATIONS GENERAL Self-contained, electric refrigerated, wall hung water cooler. Capacity of 50°F drinking water based upon 80°F inlet water and 90°F ambient. NOTE: Minimum 40 psi supply line pressure required in special circumstances where both sides of bi-level are in use simultaneously to ensure adequate stream height. Does not apply to non-refrigerated units.
PAGE 2
No Lead Two-Level Wall Mount Water Cooler Models EWTLA8K, EWTLA14K and EWTLA16K NOTE: WATERFLOW DIRECTION INSTALLER PLEASE NOTE: THIS WATER COOLER HAS BEEN DESIGNED AND BUILT TO PROVIDE WATER TO THE USER WHICH HAS NOT BEEN ALTERED BY MATERIALS IN THE COOLER WATER WAYS. THE GROUNDING OF ELECTRICAL EQUIPMENT SUCH AS TELEPHONE, COMPUTERS, ETC. TO WATER LINES IS A COMMON PROCEDURE. THIS GROUNDING MAY BE IN THE BUILDING BUT MAY ALSO OCCUR AWAY FROM THE BUILDING.