EZ8WSLSMC_1G EZ8WSSSMC_1G LZ8WSLSMC_1G LZ8WSSSMC_1G Elkay EZH2O Refrigerated Surface Mount Bottle Filling Station(s) series EZ8WS & LZ8WS INSTALLATION MANUAL (630) 574-8484 1000006137 (Rev.
EZ8WSLSMC_1G EZ8WSSSMC_1G LZ8WSLSMC_1G LZ8WSSSMC_1G Contents 1. General Information . . . . . . . . . . . . . . . . . . . . . . . 3 1.1 Installation Manual . . . . . . . . . . . . . . . . . . . . . 3 1.2 Disclaimer . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1.3 Serial Number Location . . . . . . . . . . . . . . . . . 3 1.4 Contact Information . . . . . . . . . . . . . . . . . . . . 3 1.5 Notice of Changes . . . . . . . . . . . . . . . . . . . . . 3 1.6 Warranty . . . . . .
EZ8WSLSMC_1G EZ8WSSSMC_1G LZ8WSLSMC_1G LZ8WSSSMC_1G 1. General Information 1.3 Serial Number Location 1.1 Installation Manual Please use the serial number located on the underside of the water cooler when contacting us with questions concerning the installation of this product. Read all instructions carefully BEFORE starting the installation and familiarize yourself with the various parts of this product.
EZ8WSLSMC_1G EZ8WSSSMC_1G 1.6 Warranty LZ8WSLSMC_1G LZ8WSSSMC_1G 2. Safety This product is covered by a Limited Warranty and Elkay will not be held responsible for damage of any kind in connection with the installation of the product. THINK SAFETY! Refer to the Elkay website http://www.elkay.com/ warranty and click on drinking water products, 'Warranty for Drinking Water Products' article under the Info and Maintenance section (form 96993C).
EZ8WSLSMC_1G EZ8WSSSMC_1G LZ8WSLSMC_1G 2.3 Personal Safety WARNING These warnings indicate a potentially hazardous situation which, if not avoided, could result in serious injury or death. Follow all instructions related to the installation and/or maintenance of this product (unit). death.
53.04in 1347mm X2 FILTER ACTIVATION SENSOR 25.00in 635mm WASTE OUTLET FLOOR A 7.00in 178mm X2 0.56in 14mm X2 5.50in 140mm BASIN DRAIN 4.50in 114mm WASTE OUTLET 3.50in 89mm WATER INLET 2.50in 63mm ELEC. OUTLET 17.89in 454mm 5.75in 146mm X2 1.37in 35mm X2 15.00in 381mm 5/16" (8mm) MOUNTING HOLES X4 7/16" (11mm) MOUNTING HOLES X 12 WALL 4.31in 109mm A 39.98in 1016mm ACTIVATION SENSOR FLOOR 11.89in 302mm 3.44in 87mm SECTION A-A 27.37in 695mm BASIN DRAIN 34.
EZ8WSLSMC_1G EZ8WSSSMC_1G Use Proper Tools Always use proper tools which are in good working condition during the installation of the product. Using tools other than those listed could adversely affect the product and could result in property damage. LZ8WSLSMC_1G LZ8WSSSMC_1G 3. Tools and Supplies 3.1 Tools Required Tool 2.4 Property Damage Inspect Before Cutting Make sure no electrical wiring or plumbing is present before cutting into a wall.
EZ8WSLSMC_1G EZ8WSSSMC_1G 4. Preparation 4.1 General Information 1. This water cooler is designed for indoor use only and should not be installed outdoors or in a humid environment. A water supply pressure below 20 psi will result in decreased water flow through the unit and damage to the product. A pressure above 105 psi will also cause damage to the product. NOTICE 2. Make sure the water supply pressure to the product is between 20 and 105 psi.
EZ8WSLSMC_1G EZ8WSSSMC_1G LZ8WSLSMC_1G LZ8WSSSMC_1G 5. Installation of Cooler 5.1 Mounting Instructions 1. Remove the front cover by removing the two 5/16" hex screws on the bottom side of the cooler. 3. Install the hanger bracket with five screws in 7/16" diameter mounting holes. Note: Hanger bracket MUST be supported securely. Add fixture support carrier if wall will not provide adequate support. Front Cover 4. Hang unit onto the hanger bracket. 2. Remove the hanger bracket. 5.
EZ8WSLSMC_1G EZ8WSSSMC_1G LZ8WSLSMC_1G LZ8WSSSMC_1G 6. Installation of Bottle Filler 1. Remove the two (2) mounting screws securing the top cover to the bottle filler with 5/32" Allen wrench. Remove the top cover. 4. Install the wall mounting plate to the wall using six (6) 7/16" screws through the mounting holes. Use appropriate fasteners for your wall type. Note: Do not discard the mounting screws, they will be needed to reinstall the top cover.
EZ8WSLSMC_1G EZ8WSSSMC_1G 7. Attach the bottle filler to the three (3) angled tabs on the mounting plate. LZ8WSLSMC_1G LZ8WSSSMC_1G 10. Reinstall the top cover on the bottle filler. 8. Tilt top of the bottle filler towards the mounting plate. 11. Connect the bottle filler water line inside the water cooler. 9. Slide the bottle filler down to nest in place. Rib on the basin should be behind the bottle filler alcove. 12. Connect all drain and water supply fittings. 13. Turn on water supply.
EZ8WSLSMC_1G EZ8WSSSMC_1G LZ8WSLSMC_1G LZ8WSSSMC_1G 7. Installation of Filter (LZ Only) 1. Install the filter cartridge: • • • • Remove the filter from the carton. Remove the protective cap. Mark the current date on the water filter label. Attach the filter to the filter head with label facing outward by firmly inserting into the head and by rotating the filter head clockwise, if required. Note: Filter label should be readable from the front of the filter during installation. 8. Startup 5.
EZ8WSLSMC_1G EZ8WSSSMC_1G LZ8WSLSMC_1G LZ8WSSSMC_1G 9. Changing the Factory Default Settings (Not Required for Installation) 9.1 Accessing the Programming Button 9.4 Change the Range Of The IR Sensor 1. Remove the bottle filler top cover by removing the two screws using a 5/32” Allen wrench. Do not discard the screws, they are required for re-assembly. 1. Depress the program button when the display reads RNG SET. 2.
EZ8WSLSMC_1G EZ8WSSSMC_1G LZ8WSLSMC_1G LZ8WSSSMC_1G 9.7 Resetting the Bottle Count 1. Depress the program button when the display reads RST BCNT. 2. The display will show the current value, e.g. 0033183. 3. Depress the button again to change the value to 0. The display will show BTLCT = 0 for approximately 2 seconds and return to run mode showing 0000000 on the display board. Note: Once the bottle count is reset to 0, there is no way to return to the previous count. 4.
EZ8WSLSMC_1G EZ8WSSSMC_1G LZ8WSLSMC_1G LZ8WSSSMC_1G LIMITED PRODUCT WARRANTY SOFTWARE LICENSE FIRST YEAR - - The Manufacturer warrants every cooler, bottle filling station, packaged water cooler, fountain and accessory to be free from defects in materials and workmanship under normal use for one (1) year from date of install or eighteen (18) months from date of shipment from factory, whichever occurs first.
EZ8WSLSMC_1G EZ8WSSSMC_1G LZ8WSLSMC_1G Elkay Manufacturing Company Page 16 LZ8WSSSMC_1G (630) 574-8484 1000006137 (Rev.
