Installation Instructions

ManualsBrandsElkay ManualsDrinking FountainsElkay 18-3/8" Wall Mounted Single Station with Cooler

Page 1

EZO4*1E EZO8*1E

98940C (Rev. B - 11/12)

EZO La Barrera de la serie Liberta Agua Coolers

Manual de Instalación, Cuidado y Utilización

Manuel d’installation/entretien/utilisation

EZO Coolers d’Eau de Barrière-Libère de feuilleton

EZO Series Barrier-Free Water Coolers

INSTALLATION, CARE & USE MANUAL

3, 4

16, 17

27, 28, 29

31, 32, 43

Sensor Eye

Adjustment screw

See FIG. 4

See FIG. 3

Uses HFC-134A refrigerant

Usa refrigerante HFC-134A

Utilise du fluide frigorigéne HFC-134A

FIG. 1

Summary of content (7 pages)

PAGE 1
EZO4*1E EZO8*1E INSTALLATION, CARE & USE MANUAL Manual de Instalación, Cuidado y Utilización Manuel d’installation/entretien/utilisation TM EZO Series Barrier-Free Water Coolers TM EZO La Barrera de la serie Liberta Agua Coolers TM EZO Coolers d’Eau de Barrière-Libère de feuilleton 34 35 12 39 15 18 19 13 24 16, 17 36 8 5 23 9 Uses HFC-134A refrigerant Usa refrigerante HFC-134A Utilise du fluide frigorigéne HFC-134A 45 44 3, 4 6 Sensor Eye Adjustment screw See FIG. 4 37 See FIG.
PAGE 2
FIG. 2 98940C (Rev. B - 11/12) Page 2 **NEW INSTALLATIONS MUST USE GROUND FAULT CIRCUIT INTERRUPTER (GFCI) **LAS NUEVAS INSTALACIONES DEBEN UTILIZAR LOS INTERRUPTORES DE CIRCUITO DE TIERRA DE LA AVERÍA (GFCI) **LES NOUVELLES INSTALLATIONS DOIVENT EMPLOYER LES INTERRUPTEURS DE CIRCUIT MOULUS DE DÉFAUT (GFCI) LEGEND/LEYENDA/LÉGENDE A = RECOMMENDED WATER SUPPLY LOCATION 3/8 O.D. UNPLATED COPPER TUBE CONNECT STUB WITH SHUT OFF (BY OTHERS) 3 IN.
PAGE 3
EZO4*1E HANGER BRACKETS & TRAP INSTALLATION 1) Remove hanger bracket fastened to back of cooler by removing one (1) screw. 2 ) Mount the hanger bracket as shown in Figure 2. NOTE: Hanger Bracket MUST be supported securely. Add fixture support carrier if wall will not provide adequate support. Anchor hanger securely to wall using all six (6) 1/4 in. dia. mounting holes. IMPORTANT: 5-7/8 in. (150mm) dimension from wall to centerline of trap must be maintained for proper fit.
PAGE 4
EZO4*1E EZO8*1E Service Instructions Bubbler Lower and Upper Shroud To access the refrigeration system and plumbing connections, remove four screws from bottom of cooler to remove the lower shroud. To remove the upper shroud for access to the pushbars, regulator, solenoid valve or other components located in the top of the unit, remove lower shroud, disconnect drain, remove four screws from tabs along lower edge of upper shroud, unplug two wires and water tube.
PAGE 5
EZO4*1E EZO8*1E SENSOR RANGE ADJUSTMENT: The electronic sensor used in this cooler is factory pre-set for a “visual” range of 36 inches (914 mm). If actual range varies greatly from this or a different setting is desired, follow the range adjustment procedure below: - Using a small tip screwdriver, locate range adjustment screw through the small hole between the sensor lenses (See Page 1.) Turn this screw clockwise to increase range and counterclockwise to decrease range (See Fig. 3).
PAGE 6
EZO4*1E EZO8*1E Cleaning the strainer To clean the strainer, unscrew the cap of the solenoid valve. Remove screen and rinse thoroughly with water. Insert screen back into solenoid valve and screw cap on. Make sure the o-ring is placed properly. 11 Screen Malla Ecran Limpieza del filtro Para limpiar el filtro, desatornille la tapa de la válvula solenoide. Retire la malla y enjuague a fondo con agua. Inserte nuevamente la malla en la válvula solenoide y atornille la tapa.
PAGE 7
EZO4*1E EZO8*1E PARTS LIST/LISTA DE PIEZAS/LISTE DES PIÈCES ITEM NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 *30 31 32 34 35 36 37 38 39 40 41 42 43 44 45 46 PART NO.