EZOOTL8*1A LZOOTL8*1A INSTALLATION AND USE MANUAL EZOOTL ™& LZOOTL™Series Sensor-Operated Versatile Bi-Level Water Coolers EZOOTL™ & LZOOTL™ Serie de enfriadores de agua de dos niveles versátiles operados por sensor EZOOTL™ & LZOOTL™ Refroidisseurs d’eau polyvalents à deux niveaux commandés par capteur série Versatile Cooler Model EZOOSTL8LC configuration as shipped *Versatile Cooler Model EZOOSTL8LC alternate installation *Versatile Cooler Model LZOOSTL8LC alternate installation Versatile Cooler Mode
EZOOTL8*1A INSTALLER PLEASE NOTE: IMPORTANT This water cooler has been designed and built to provide water to the user which has not been altered by materials in the cooler water ways. The grounding of electrical equipment such as telephones, computers, etc. to water lines is a common procedure. This grounding may be in the building but may also occur away from the building.
EZOOTL8*1A TROUBLE SHOOTING & MAINTENANCE GUIDE 15. BUBBLER: Mineral deposits on the orifice can cause water flow to spurt or not regulate. Mineral deposits may be removed from the orifice with a small round file not over 1/8” diameter or small diameter wire. CAUTION: DO NOT file or cut orifice material. Care must be taken not to damage the orifice(s). 16. Stream Regulator: If orifice is clean, regulate flow as in “START UP” instructions above.
EZOOTL8*1A LZOOTL8*1A Note: Danger! Electrical shock hazard. Disconnect power before servicing unit. Nota: peligro! Peligro de descarga eléctrica. Desconecte antes de reparar la unidad Remarque : Danger ! Risque de choc électrique. Débrancher avant de réparer l’appareil.
EZOOTL8*1A LZOOTL8*1A Uses HFC-134A refrigerant Usa refrigerante HFC-134A Utilise du fluide frigorigéne HFC-134A 13 14 1 36 5 5 27 23 18 19 7 37 18 19 8 See Fig. 8 Vea la figura 8 Voir la Figure 8 Sensor Eye Adjustment screw Tornillo de ajuste de ojo del sensor Vis de réglage de l’oculaire de capteur See Fig. 7 Vea la figura 7 Voir la Figure 7 Sensor Eye Adjustment screw Tornillo de ajuste de ojo del sensor Vis de réglage de l’oculaire de capteur See Fig.
1000005928 (Rev. C - 07/21) FIG.
E FIG. 4 Page 7 3-7/8" (98mm) 7" (178mm) 7" (178mm) 7/8" (22mm) 2" (51mm) B 2" (51mm) F 22-15/16" (583mm) 19-7/16" (494mm) 2" (51mm) 19" (484mm) 12-1/2" (318mm) C 3" (76mm) 17/16" (37mm) HANGER BRACKET FILTER 8-1/16" (205mm) 27" (686mm) ADA REQUIREMENT 31-5/16" (796mm) RIM HEIGHT 32-7/8" (835mm) ORIFICE HEIGHT 36-13/16" (936mm) RIM HEIGHT 38-3/8" (975mm) ORIFICE HEIGHT 34-5/16" (872mm) 24-1/2" (622mm) A PREFFERED LOCATION E ELECTRIC EYE LOCATION D (ALT.
EZOOTL8*1A LZOOTL8*1A Versatile Wrapper and Trim Kit Installation Instructions Left Hand Wrapper (High Side) 1) Remove existing wrapper by removing the (4) screws from bottom. 2) Screw trim piece to wrapper with (2) screws (provided) 3) Re-install wrapper with (4) screws. 4) Dispose of unused Right Hand Wrapper (Low Side) 1) Remove existing wrapper by removing the (4) screws from bottom. 2) Clip cover plate, sliding until plate sits flush with the wall. 3) Re-install wrapper with (4) screws.
EZOOTL8*1A HANGER BRACKETS INSTALLATION 1) Retire el soporte fijador que se encuentra conectado a la parte posterior del enfriador sacando un (1) tornillo. 2) Monte el soporte fijador de la manera descrita en Fig. 3, 4. NOTA: Es necesario que el soporte fijador sea apoyado seguramente. Agregue un portador al soporte fijador si La pared no aporta soporte adecuado. Amarre el soporte colgante seguramente a la pared. Usando todos los seis (6) agujeros de montaje de ¼ pulg. (6.35 mm) de diám.
EZOOTL8*1A LZOOTL8*1A - El LED verde (Bueno) indica que el filtro está funcionando Green LED (Good) indicates that the filter is operating within 0% - 80% of its life. - Yellow LED indicates that the filter is operating within 80% - 100% of its life. - Red LED (Replace) indicates that the filter needs to be replaced since it has reached end of filter life. installé, une consommation d’eau incorrecte sera calculée.
EZOOTL8*1A LZOOTL8*1A 17 4 17 23 or 36 (Item 36 Shown) 20 37 7 33 20 Sensor Eye Adjustment Screw 9 32 Sensor Eye Adjustment Screw REGULATOR ASSEMBLY 11 10 35 ALIGNMENT NOTCH 34 SNAP 8 REGULATOR ASSEMBLY 11 ALIGNMENT NOTCH SNAP SNAP SNAP ALIGNMENT PEG ALIGNMENT PEG FIG. 6 EZOOSTL8LC Model (LH & RH Cooler Units) LZOOSTL8LC Model (LH Cooler Unit Only) Page 11 FIG. 7 LZOOSTL8LC Model (RH Cooler Unit Only) 1000005928 (Rev.
EZOOTL8*1A LZOOTL8*1A 17 Basin FIG. 8 NOTE: BUBBLER DETAIL Locknut When installing replacement bubbler and pedestal, tighten locknut only to hold parts snug in position. Do Not Overtighten. 2 3/8” Water Inlet 1 Fig. 9 (For LZOOSTL8LC only) WATERSENTRY® Filter Detail Detalle WATERSENTRY® Filtro Description WATERSENTRY® Filtrage WATERSENTRY® FILTER PARTS LIST ITEM NO. PART NO. 1 2 51299C 0000000895 1000005928 (Rev. C - 07/21) LISTA DE PIEZAS DEL FILTRO DESCRIPTION Filter Assy-1500 Gal.
EZOOTL8*1A LZOOTL8*1A EZOOSTL8LC LZOOSTL8LC EZ-LZ Series 115V PARTS LIST 1 2 3 4 5 *6 7 8 9 10 11 12 13 14 X X X X X X X X X X 15 16 17 18 X X X X X X X X X X X X X X X X X X X X X X X X 28 29 30 31 32 33 34 35 36 X X X X X X X X X X ITEM NO. 19 20 21 22 23 24 25 26 27 X X X X X X X X X X X X X X X X X PART NO.
