Installation Sheet

ManualsBrandsElkay ManualsCommercial PlumbingEZH2O Wall Mounted Bi-Level Drinking Fountain and Hands Free Bottle Filling Station with Cooler

Page 1 1000002243 (Rev. H - 01/21)

EZSTLDWS*1G EZSTL8WS*1G, 2G, 3G LZSTLDWS*1G LZSTL8WS*1G, 2G, 3G

EZ™ & LZ™ Stations versatile de Remplissage de Bouteille Série et Refroidisseurs

EZ™ & LZ™ Serie versatil Botella Bombas y Enfriadores

™

& LZ™ Series Versatile Bottle Filling Stations & Coolers

INSTALLATION & USE MANUAL

Manual de instalación y uso

Manuel d’installation et utilisation

*Versatile Cooler Model LZSTL8WSLK

conguration as shipped

*Versatile Cooler Model LZSTL8WSLK

alternate installations

*Versatile cooler design allows units to be

installed either left-hand high and right-hand low

or left-low and right high.

Basin change may be required. See desired

rough-in to help determine if the basin change is

necessary.

Refrigerated unit must be installed on right-hand

side.

Summary of content (18 pages)

PAGE 1
EZSTLDWS*1G EZSTL8WS*1G, 2G, 3G LZSTLDWS*1G LZSTL8WS*1G, 2G, 3G INSTALLATION & USE MANUAL Manual de instalación y uso Manuel d’installation et utilisation EZ ™ & LZ™ Series Versatile Bottle Filling Stations & Coolers EZ™ & LZ™ Serie versatil Botella Bombas y Enfriadores EZ™ & LZ™ Stations versatile de Remplissage de Bouteille Série et Refroidisseurs *Versatile Cooler Model LZSTL8WSLK alternate installations *Versatile Cooler Model LZSTL8WSLK configuration as shipped *Versatile cooler design allows uni
PAGE 2
EZSTLDWS*1G EZSTL8WS*1G, 2G, 3G LZSTLDWS*1G LZSTL8WS*1G, 2G, 3G Note: Danger! Electric shock hazard. Disconnect power before servicing unit. Nota: peligro! Peligro de descarga eléctrica. Desconecte antes de reparar la unidad. Remarque : Danger ! Risque d'électrocution. Débrancher avant de réparer l'appareil. Pictured is unit only without bottle filler. En la foto, la unidad sólo sin relleno botella. Sur la photo, est une unité seulement sans remplissage de la bouteille.
PAGE 3
Fig. Fig. 22 Page Page 33 2" 51mm 7/8" 22mm 13 15/16" 354mm D (ALT.
PAGE 4
1000002243 1000002243 (Rev. (Rev. F H -- 07/19) 01/21) Fig. Fig. 33 Page Page 44 F A (ALT. LOCATION) 3 7/8" 98mm 6 3/8" 162mm ‰ D PREFERRED LOCATION 2" 51mm 7/8" 22mm 6 3/8" 162mm 7" 178mm ‰ 7" 178mm 5 3/4" 146mm 2" 51mm 6 3/8" 162mm FINISHED FLOOR D (ALT.
PAGE 5
Fig. 4 Fig. 4 E B A (ALT. LOCATION) 3 7/8" 98mm 6 3/8" 162mm ‰ D PREFERRED LOCATION 2" 51mm 7/8" 22mm 6 3/8" 162mm 7" 178mm 5 3/4" 146mm 2" 51mm 6 3/8" 162mm FINISHED FLOOR D (ALT.
PAGE 6
1000002243 F -- 07/19) 1000002243 (Rev. (Rev. H 01/21) Fig. Fig.
PAGE 7
EZSTLDWS*1G EZSTL8WS*1G, 2G, 3G LZSTLDWS*1G HANGER BRACKETS INSTALLATION 1) Remove hanger brackets fastened to back of cooler by removing one (1) screw. 2) Mount the hanger brackets as shown in Figures 2, 3, 4 or 5. NOTE: Hanger Bracket MUST be supported securely. Add fixture support carrier if wall will not provide adequate support. Anchor hanger securely to wall using all six (6) 1/4 in. dia. mounting holes. INSTALLATION OF COOLER 3) Hang the cooler on the hanger bracket.
PAGE 8
EZSTLDWS*1G EZSTL8WS*1G, 2G, 3G LZSTLDWS*1G LZSTL8WS*1G, 2G, 3G Service Instructions Lower and Upper Shroud 11 To access the refrigeration system and plumbing connections, remove four screws from bottom of cooler to remove the lower shroud.
PAGE 9
EZSTLDWS*1G EZSTL8WS*1G, 2G, 3G LZSTLDWS*1G 7/16” BOLT HOLES FOR FASTENING UNIT TO WALL UNIT CENTER LINE LZSTL8WS*1G, 2G, 3G TOP COVER Fig. 8 MOUNTING SCREWS 31 Fig. 9 BRACKET & SCREWS Fig. 10 Fig. 11 Bottle Filler Installation Instructions 1) Remove two (2) mounting screws with 5/32” Allen wrench holding top cover to Bottle Filler (See Fig. 9). Remove top cover. Note do not discard mounting screws, they will be needed to reinstall top cover. 2) Remove wall mounting plate from Bottle Filler.
PAGE 10
EZSTLDWS*1G EZSTL8WS*1G, 2G, 3G LZSTLDWS*1G LZSTL8WS*1G, 2G, 3G BF11 - BF12 PROGRAM SETTING THE CONTROL BOARD VERIFY CONTROL BOARD SOFTWARE 1) To verify the software program of the control board the unit will need to be shut down and restarted. The chiller (if present) does not need to be shut down and restarted. 2) The units lower panel must be open to access the power cord and wall outlet.
PAGE 11
EZSTLDWS*1G EZSTL8WS*1G, 2G, 3G LZSTLDWS*1G LZSTL8WS*1G, 2G, 3G INSTRUCTIONS TO MOVE THE BOTTLE FILLER & BASIN TO THE LEFT SIDE (NON-REFRIGERATED) FOR ALTERNATE MOUNTING VERSATILE BI-LEVEL Using a 5/16" socket, remove the (4) screws from the bottom of each cooler to remove the wrappers. Using a #T20 (6 point star bit), loosen the shroud screws. Both sides, both coolers. ONLY move the filler panel and j-clip to the refrigerated (right) side if right side will be mounted 'high'.
PAGE 12
EZSTLDWS*1G EZSTL8WS*1G, 2G, 3G LZSTLDWS*1G LZSTL8WS*1G, 2G, 3G INSTRUCTIONS CONTINUED..... Swap drain parts in shroud: Loosen each hose clamp retaining the drain pieces. Remove each drain piece and swap to other basin. Tighten each hose clamp. Refrigerated Cooler side: Carefully lift and tip the shroud/basin assembly off of the cooler frame. Only disconnect the (2) black wires coming from the shroud assembly that go to the solenoid valve and to the cold control.
PAGE 13
EZSTLDWS*1G EZSTL8WS*1G, 2G, 3G LZSTLDWS*1G LZSTL8WS*1G, 2G, 3G Versatile Wrapper and Trim Kit Installation Instructions Left Hand Wrapper (High Side) 1) Remove existing wrapper by removing the (4) screws from bottom. 2) Screw trim piece to wrapper with (2) screws (provided) 3) Re-install wrapper with (4) screws. 4) Dispose of unused Right Hand Wrapper (Low Side) 1) Remove existing wrapper by removing the (4) screws from bottom. 2) Clip cover plate, sliding until plate sits flush with the wall.
PAGE 14
EZSTLDWS*1G EZSTL8WS*1G, 2G, 3G LZSTLDWS*1G LZSTL8WS*1G, 2G, 3G PLUMBING DIAGRAMS VERSATILE BI-LEVEL Bottle Filler Drain Bottle Filler Drain Bottle Filler Drain Bottle Filler Drain 1000002243 (Rev.
PAGE 15
Tee 3/8” Water Inlet Evaporator R.H. Refrig. unit Page 15 Filter Assembly 1/4” Union regulator Bubbler L.H. Non-Refrig unit Solenoid Valve 3/8” Water Inlet Solenoid Valve regulator Bubbler Tee 3/8” Water Line from Bottle Filling Unit Standard EZ Bi-Level Pressurized Plumbing Diagram regulator Bubbler Solenoid Valve Evaporator R.H. Refrig.
PAGE 16
EZSTLDWS*1G EZSTL8WS*1G, 2G, 3G LZSTLDWS*1G LZSTL8WS*1G, 2G, 3G SWITCHES Fig. 12 11 Locknut Tuerca de Fijación Écrou de Blocage BLACK - L GREEN - GRND Basin Estanque Bassin BUBBLER DETAIL DETALLE DEL GRIFO DETAIL DU BARBOTEUR WHITE - N SOLENOID VALVE GND Fig. 13 NOTE: When installing replacement bubbler and pedestal, tighten nut only to hold parts snug in position. Do Not Overtighten.
PAGE 17
EZSTLDWS*1G EZSTL8WS*1G, 2G, 3G LZSTLDWS*1G LZSTL8WS*1G, 2G, 3G OPERATION QUICK CONNECT FITTINGS O OP PE PE ER RATI RA TIO ION ON OF O QUI UIC UI ICK CK CO C ONN ON NNE NEC ECT CT FI F IT IT TT TIN TI ING NGS GS SIMPLY PUSH SI MP US SIIM MPL PLY PUS USH SH IN I IN TU BE E TO TT TUB UB TTOATT TTA TACH C TUBE ATTACH A A TUBE T TU UBE UB BEIS I SECURED IS SE SE EC CUR URE RED ED IINPOSITION POS PO OSI SIT IT TIIO ION ON IN PUSH PUS PU USH SHIN I COLLET IN COL CO OLL LLE LET T RELEASE TO RE RE EL LEA LE E
PAGE 18
EZSTLDWS*1G ITEM NO. 28401C 55001109 0000001337 36216C 36322C 56092C 56229C 66703C 98900C 8B 97969C 9 10 11 12 13 14 55996C 1000004572 56073C 98734C 1000001600 98773C 98774C 15 98775C 16 17 98776C 98777C 18 19 20 21 22 23 24 25 26 27 28 98778C 98898C 0000000238 98724C 1000002062 1000001602 97446C 1000001994 1000001812 1000004447 35980C 36287C 1000004564 0000001339 1000000888 1000000944 1000000758 1000000759 29 30 NS NS NS = NOT SHOWN ITEM NO.