EZSG8WS*1B LZSG8WS*1B INSTALLATION & USE MANUAL Manual de instalación y uso Manuel d’installation et d’utilisation EZ™ & LZ ™ Series Bottle Filling Stations & Coolers EZ™ & LZ™ Serie versatil Botella Bombas y Enfriadores EZ™ & LZ™ Stations de Remplissage de Bouteille Série et Refroidisseurs Page 1 1000001713 (Rev.
EZSG8WS*1B LZSG8WS*1B Note: Danger! Electric shock hazard. Disconnect power before servicing unit. Nota: peligro! Peligro de descarga eléctrica. Desconecte antes de reparar la unidad. Remarque : Danger ! Risque d'électrocution. Débrancher avant de réparer l'appareil. Pictured is unit only without bottle filler. En la foto, la unidad sólo sin relleno botella. Sur la photo, est une unité seulement sans remplissage de la bouteille.
Page 3 7” (178mm) 2” (51mm) 3-7/8” (98mm) 5-3/4” (146mm) 7” (178mm) 13-15/16” (354mm) A E 32-7/8” (835mm) ORIFICE HEIGHT FINISHED FLOOR 28-13/16” (732mm) 2” (51mm) 2-7/8” (73mm) 15” (381mm) 31-5/16” (796mm) RIM HEIGHT 27” (686mm) ADA REQUIREMENT 3-9/16” (90mm) C 12-1/8” (318mm) 8-1/16” (205mm) HANGER BRACKET 19” (483mm) * 5-7/8” (150mm) 3” (77mm) 2” (51mm) 18-7/8” (479mm) *ADA REQUIREMENT *REQUISITO DE A.D.A.
EZSG8WS*1B HANGER BRACKETS & TRAP INSTALLATION 1) Remove hanger bracket fastened to back of cooler by removing one (1) screw. 2) Mount the hanger bracket as shown in Figure 2. NOTE: Hanger Bracket MUST be supported securely. Add fixture support carrier if wall will not provide adequate support. Anchor hanger securely to wall using all six (6) 1/4 in. dia. mounting holes. IMPORTANT: 5-7/8 in. (150mm) dimension from wall to centerline of trap must be maintained for proper fit.
EZSG8WS*1B LZSG8WS*1B Service Instructions Lower and Upper Shroud To access the refrigeration system and plumbing connections, remove four screws from bottom of cooler to remove the lower shroud. To remove the upper shroud for access to the pushbars, regulator, solenoid valve or other components located in the top of the unit, remove lower shroud, disconnect drain, remove four screws from tabs along lower edge of upper shroud, unplug two wires and water tube.
EZSG8WS*1B LZSG8WS*1B 7/16” BOLT HOLES FOR FASTENING UNIT TO WALL UNIT CENTER LINE TOP COVER Fig. 4 MOUNTING SCREWS 27 Fig. 5 Fig. 7 Fig. 6 BRACKET & SCREWS Bottle Filler Installation Instructions 1) Remove two (2) mounting screws with 5/32” Allen wrench holding top cover to Bottle Filler (See Fig. 5). Remove top cover. Note do not discard mounting screws, they will be needed to reinstall top cover. 2) Remove wall mounting plate from Bottle Filler. Place wall plate against wall on top of basin.
EZSG8WS*1B LZSG8WS*1B BF11 - BF12 PROGRAM SETTING THE CONTROL BOARD VERIFY CONTROL BOARD SOFTWARE 1) To verify the software program of the control board the unit will need to be shut down and restarted. The chiller (if present) does not need to be shut down and restarted. 2) The units lower panel must be open to access the power cord and wall outlet. 3) Shut down the unit by unplugging the power cord from the wall outlet. 4) Restart the unit by plugging the power cord back into the wall outlet.
EZSG8WS*1B LZSG8WS*1B NOTE: When installing replacement bubbler and pedestal, tighten nut only to hold parts snug in position. Do Not Overtighten. 11 NOTA: Basin Estanque Bassin Locknut Tuerca de Fijación Écrou de Blocage BUBBLER DETAIL DETALLE DEL GRIFO DETAIL DU BARBOTEUR Al instalar el grifo y pedestal de reemplazo, apriete la tuerca unicamente para mantener las piezas en una posicion adjustada. No dede apretarse demasiado.
EZSG8WS*1B LZSG8WS*1B OPERATION OF QUICK CONNECT FITTINGS SIMPLY PUSHIN IN SIMPLY PUSH TUBE TO TUBE TOATTACH ATTACH A A TUBE TUBEIS IS SECURED SECURED INPOSITION POSITION IN PUSH PUSHIN IN COLLET COLLET TORELEASE RELEASE TUBE TUBE TO B C PUSHING BEFORE PUSHINGTUBE TUBE IN IN BEFORE PULLING TO PULLING IT IT OUT OUT HELPS HELPS TO RELEASE RELEASE TUBE TUBE Note: Screw the locknut hand tight to seal Fig. 12 Fig. 11 3 3/8” Water Inlet 2 2 1 Fig.
EZSG8WS*1B LZSG8WS*1B 115V PARTS LIST/ 115V LISTA DE PIEZAS/ 115V LISTE DES PIÈCES DESCRIPTION DESCRIPCIÓN Hanger Bracket Basin - Stainless Steel Wiring - Front/Side Push Bar Compr - Service Pak 115V EM 65 HHC Tube - Poly (Cut To Length) Assy - Shroud - Upper (Front Side Push) Drier Kit - Drain Replacement (EZ) (Brkt, Tube, Ftg, Clamp) Kit - Replacement Cap/Screen/O-Ring Kit - Solenoid Valve/Regulator Assy Kit - Flexi Streamsaver Bubbler/ “O”-Ring/Nut Kit - Pushbar (Front/Side) EZS TL Kit - Cold Control
