EZSG8WS*1B LZSG8WS*1B INSTALLATION, CARE & USE MANUAL Manual de Instalación, Cuidado y Utilización Manuel d’installation/entretien/utilisation EZ & LZ Series Bottle Filling Stations & Coolers TM TM EZ & LZ Serie Botella Bombas y Enfriadores EZ & LZ Stations de Remplissage de Bouteille Série et Refroidisseurs TM TM TM TM Page 1 1000001713 (Rev.
EZSG8WS*1B LZSG8WS*1B Pictured is unit only without bottle filler. Uses HFC-134A refrigerant Usa refrigerante HFC-134A Utilise du fluide frigorigéne HFC-134A 1 14, 25 21 15 8 6 5 See Fig. 3 3 2 12 See Fig. 8 12 12 13 Stream Height Adjustment See Note 8 24 16 23 7 18 4 19 17 20 Fig. 1 1000001713 (Rev.
Page 3 F 7" 178mm 2" 51mm 3 7/8" 98mm 5 3/4" 146mm 7" 178mm 2" 51mm 6 3/8" 162mm 32 7/8" 835mm ORIFICE HEIGHT FINISHED FLOOR 28 13/16" 732mm 13 15/16" 354mm A E 2 7/8" 73mm 2" 51mm 15" 381mm 31 5/16" 796mm RIM HEIGHT 27" 686mm ADA REQUIREMENT 3 9/16" 90mm C 12 1/2" 318mm 8 1/16" 205mm HANGER BRACKET 19" 483mm 5 7/8" 150mm 3" 77mm 2" 51mm 18 7/8" 479mm *ADA REQUIREMENT *REQUISITO DE A.D.A.
EZSG8WS*1B HANGER BRACKETS & TRAP INSTALLATION LZSG8WS*1B INSTALACIÓN DE LOS SOPORTES FIJADORES Y EL PURGADOR 1) Remove hanger bracket fastened to back of 1) Retire el soporte fijador que se encuentra conectado cooler by removing one (1) screw. a la parte posterior del enfriador sacando un (1) tornillo. 2) Mount the hanger bracket as shown in Figure 2. Monte el soporte fijador de la manera descrita en NOTE: Hanger Bracket MUST be supported secure- 2) Fig. 2. ly.
EZSG8WS*1B LZSG8WS*1B Service Instructions Lower and Upper Shroud To access the refrigeration system and plumbing connections, remove four screws from bottom of cooler to remove the lower shroud. To remove the upper shroud for access to the pushbars, regulator, solenoid valve or other components located in the top of the unit, remove lower shroud, disconnect drain, remove four screws from tabs along lower edge of upper shroud, unplug two wires and water tube.
EZSG8WS*1B LZSG8WS*1B 7/16” BOLT HOLES FOR FASTENING UNIT TO WALL UNIT CENTER LINE TOP COVER Fig. 4 MOUNTING SCREWS 28 Fig. 5 Fig. 7 Fig. 6 BRACKET, WASHERS, & SCREWS Bottle Filler Installation Instructions 1) Remove two (2) mounting screws with 5/32” Allen wrench holding top cover to Bottle Filler (See Fig. 5). Remove top cover. Note do not discard mounting screws, they will be needed to reinstall top cover. 2) Remove wall mounting plate from Bottle Filler.
EZSG8WS*1B LZSG8WS*1B BF11 PROGRAM SETTING THE CONTROL BOARD VERIFY CONTROL BOARD SOFTWARE 1) To verify the software program of the control board the unit will need to be shut down and restarted. The chiller (if present) does not need to be shut down and restarted. 2) The units lower panel must be open to access the power cord and wall outlet. 3) Shut down the unit by unplugging the power cord from the wall outlet. 4) Restart the unit by plugging the power cord back into the wall outlet.
EZSG8WS*1B LZSG8WS*1B NOTE: When installing replacement bubbler and pedestal, tighten nut only to hold parts snug in position. Do Not Overtighten. 11 NOTA: Basin Estanque Bassin Locknut Tuerca de Fijación Écrou de Blocage BUBBLER DETAIL DETALLE DEL GRIFO DETAIL DU BARBOTEUR Al instalar el grifo y pedestal de reemplazo, apriete la tuerca unicamente para mantener las piezas en una posicion adjustada. No dede apretarse demasiado.
EZSG8WS*1B LZSG8WS*1B OPERATION OF QUICK CONNECT FITTINGS SIMPLY PUSH IN TUBE TO ATTACH A TUBE IS SECURED IN POSITION B C Note: Screw the locknut hand tight to seal Fig. 12 Fig. 11 PUSH IN COLLET TO RELEASE TUBE PUSHING TUBE IN BEFORE PULLING IT OUT HELPS TO RELEASE TUBE 3 2 2 1 Fig.13 WATERSENTRY® Filter Detail Detalle WATERSENTRY® Filtro Description WATERSENTRY® Filtrage WATERSENTRY® FILTER PARTS LIST (See Fig. 13) LISTA DE PIEZAS DEL FILTRO (Vea la Fig.
EZSG8WS*1B LZSG8WS*1B 115V PARTS LIST/ 115V LISTA DE PIEZAS/ 115V LISTE DES PIÈCES DESCRIPTION DESCRIPCIÓN Hanger Bracket Basin - Stainless Steel Wiring - Front/Side Push Bar Compr - Service Pak 115V EM 65 HHC Tube - Poly (Cut To Length) Assy - Shroud - Upper (Front Side Push) Drier Kit - Drain Replacement (EZ) (Brkt, Tube, Ftg, Clamp) Kit - Replacement Cap/Screen/O-Ring Kit - Solenoid Valve/Regulator Assy Kit - Flexi Streamsaver Bubbler/ “O”-Ring/Nut Kit - Pushbar (Front/Side) EZS TL Kit - Cold Control
