EZF(S)8*1G, 2G, 3G LZF(S)8*1G, 2G, 3G INSTALLATION, CARE & USE MANUAL Manual de Instalación, Cuidado y Utilizaci Manuel d’installation/entretien/utilisation EZ™ & LZ™ Series Barrier-Free Water Coolers EZ™ & LZ™ La Barrera de la serie Liberta Agua Coolers EZ™ & LZ™ Coolers d’Eau de Barrière-Libère de feuilleton Model EZS8L Page 1 1000003086 (Rev.
EZF(S)8*1G, 2G, 3G LZF(S)8*1G, 2G, 3G Note: Danger! Electrical shock hazard. Disconnect power before servicing unit. Nota: peligro! Peligro de descarga eléctrica. Desconecte antes de reparar la unidad Remarque : Danger ! Risque de choc électrique. Débrancher avant de réparer l’appareil.
Page 3 F 7" 178mm 2" 51mm 3 7/8" 98mm 28 13/16" 732mm 13 15/16" 354mm A E 2" 51mm C 8 1/16" 205mm FINISHED FLOOR ADA REQUIREMENT 27" 686mm RIM HEIGHT 31 11/32" 796mm ORIFICE HEIGHT 32 7/8" 835mm 12 1/2" 318mm 5 7/8" 150mm HANGER BRACKET REDUCE HEIGHT BY 3” FOR INSTALLATION OF CHILDREN’S ADA COOLER 7" 178mm 5 3/4" 146mm CL 6 3/8" 162mm 19 1/32" 483mm 3" 77mm 2" 51mm LEGEND/LEYENDA/LÉGENDE A = RECOMMENDED WATER SUPPLY LOCATION 3/8” O.D.
EZF(S)8*1G, 2G, 3G LZF(S)8*1G, 2G, 3G HANGER BRACKETS & TRAP INSTALLATION INSTALACIÓN DE LOS SOPORTES FIJADORES Y EL PURGADOR INSTALLATION DES SUPPORTS DE SUSPENSION ET DU SIPHON 1) Remove hanger bracket fastened to back of cooler by 1) Retire el soporte fijador que se encuentra conectado a 1) Retirez le support de suspension fixé au dos du la parte posterior del enfriador sacando un (1) tornillo. refroidisseur en retirant une (1) vis. removing one (1) screw.
EZF(S)8*1G, 2G, 3G LZF(S)8*1G, 2G, 3G Service Instructions Lower and Upper Shroud To access the refrigeration system and plumbing connections, remove four screws from bottom of cooler to remove the lower shroud. To remove the upper shroud for access to the pushbars, regulator, solenoid valve or other components located in the top of the unit, remove lower shroud, disconnect drain, remove four screws from tabs along lower edge of upper shroud, unplug two wires and water tube.
EZF(S)8*1G, 2G, 3G LZF(S)8*1G, 2G, 3G NOTE: When installing replacement bubbler and pedestal, tighten nut only to hold parts snug in position. Do Not Overtighten. NOTA: Al instalar el grifo y pedestal de reemplazo, apriete la tuerca unicamente para mantener las piezas en una posicion adjustada. No dede apretarse demasiado.
EZF(S)8*1G, 2G, 3G LZF(S)8*1G, 2G, 3G 17 OVERLOAD BLK 3 1 2 COLD CONTROL C FAN 5 3 2 1 SOLENOID VALVE GREEN - GND 6 WHT RELAY (WHITE - N) M S (BLACK - L) Fig. 8 115V Wiring Diagram Esquema eléctrico 115V Diagramme de câblage 115V GND 17 OVERLOAD 3 1 COLD CONTROL 2 WHT C M 5 3 2 SOLENOID VALVE 1 RIBBED 220V Wiring Diagram Esquema eléctrico 220V Diagramme de câblage 220V 6 GREEN - GND FAN Fig.
EZF(S)8*1G, 2G, 3G LZF(S)8*1G, 2G, 3G ITEM NO.
