Installation Sheet

ManualsBrandsElkay ManualsDrinking FountainsNon-Filtered Non-Refrigerated EZH2O Integral SwirlFlo Stainless Steel Drinking Fountain with Bottle Filling Station

0000001029 (Rev.C - 11/14)

EZWS-EDFPBM117K LZWS-EDFPBM117K

Page 1

Review these instructions before beginning installation. Be sure that installation

conforms to all plumbing, electrical and other applicable codes.

When installation is complete, ensure these instructions are left in the plastic bag

provided inside the installed unit for future reference.

Service to be performed by authorized service personnel only.

INSTALLER

NOTE: It is common practice to ground electrical hardware such as telephones, computers and other devices

to available water lines. This can, however, cause electrical feedback in the plumbing circuit, which

results in an “electrolysis” effect occurring in the fountain. This may result in water which has a

metallic taste to it or has a noticeable increase in the metallic content of the water.

When inspecting plumbing circuit, remember the line may be grounded some distance from the

installation, and may occur outside the building or area in which the unit is being installed.

This condition can be avoided (in most cases) by using recommended materials during installation.

Any drain ttings provided by the installer should be made of plastic which will electronically isolate

the fountain from the remainder of the building’s plumbing circuits.

SWIRLFLO

™

Fountains with FLEXI-GUARD

™

and EZH

™

Bottle Filler

INSTALLATION, CARE & USE MANUAL

LZWS-EDFPBM117KEZWS-EDFPBM117K

Summary of content (9 pages)

PAGE 1
EZWS-EDFPBM117K LZWS-EDFPBM117K INSTALLATION, CARE & USE MANUAL SWIRLFLO™ Fountains with FLEXI-GUARD™ and EZH2O™ Bottle Filler EZWS-EDFPBM117K LZWS-EDFPBM117K INSTALLER Review these instructions before beginning installation. Be sure that installation conforms to all plumbing, electrical and other applicable codes. When installation is complete, ensure these instructions are left in the plastic bag provided inside the installed unit for future reference.
PAGE 2
0000001029 (Rev. C - 11/14) Fig. 1 Page 2 OPTIONAL ACCESS PANEL 18 11/16" 475mm 1 5/8" 41mm 1 5/8" 41mm 27" 686mm ADA REQUIREMENT 33 15/16" 862mm 41 11/16" 1058mm 44 3/4" 1137mm ACTIVATION SENSOR OPTIONAL ACCESS PANEL **NEW INSTALLATIONS MUST USE GROUND FAULT CIRCUIT INTERRUPTER *GFCI) LEGEND A = 1/4” O.D. Tube - Water Outlet Connection B = 3/8” O.D.
PAGE 3
EZWS-EDFPBM117K TO BUBBLER LZWS-EDFPBM117K TO BUBBLER REQUIRED TOOLS AND MATERIALS These tables show special tools and/or additional materials (not provided) which are necessary to complete installation of these units: 12 12 Special Tools Item 13 14 Additional Materials Not Included Item 25 26 32 Quantity NONE 12 TO BOTTLE FILLER Description WATER INLET Figure 2 - EZWS-EDFPBM117K Tube Routing Description 1 Unplated copper inlet pipe 2 Service Stop/Shut-off Valve 3 90° 1-1/4” Drain Li
PAGE 4
EZWS-EDFPBM117K LZWS-EDFPBM117K 28, 29, 30, 31, 32 8. Install reset switch for bottle filler (Fig 5). Connect the switch wire to the extension wire on the back of the bottle filler. Wrap up the excess cord. 9. Attach waste tubes (1-1/4” O.D.) to 1-1/4” O.D. slip trap. Trap on the bottle filler side must be 1-1/2” O.D. (provided by others). 16 10. Make final water supply connections. 11. These products are designed to operate on 20-105 PSIG supply line pressure.
PAGE 5
EZWS-EDFPBM117K LZWS-EDFPBM117K 1 Basin Locknut FLEXI-GUARD® BUBBLER DETAIL NOTE: When installing replacement bubbler and pedestal, tighten locknut only to hold parts snug in position. Do Not overtighten. Figure 6 - Bubbler Details 3 2,3 2,3 3 FILTER PARTS LIST (See Fig. 9) 1 ITEM NO. LISTA DE PIEZAS DEL FILTRO (Vea la Fig. 9 LISTE DES PIÈCES DU FILTRE (Voir Fig. 9) DESCRIPTION PART NO. DESCRIPTION DESCRIPCIÓN 1 2 51300C 98926C Filter Assy-3000 Gal.
PAGE 6
EZWS-EDFPBM117K LZWS-EDFPBM117K 11 See Fig. 6 2 9 See Fig. 6 10 3 18 5 12 21 8 4 Figure 8 - Fountain Body Assembly 21 6 7 8 20 Figure 9 - Push Button Assembly 0000001029 (Rev.
PAGE 7
EZWS-EDFPBM117K LZWS-EDFPBM117K BF11 PROGRAM SETTING THE CONTROL BOARD Continued from below: 2) When the display changes to “SETTINGS”, depress the button again. The display will change to show “RNG SET” - Range set for IR sensor. “UNIT TYP” - Type of unit (REFRIG or NON-RFRG) “FLT SIZE” - Select filter capacity “RST BCNT” - Reset bottle count 3) When display shows “UNIT TYPE” push program button once the display will show current value. Can be REFRIG or NON-RFRG 4) Push button once to change value.
PAGE 8
EZWS-EDFPBM117K LZWS-EDFPBM117K MAIN PANEL MOUNTING FRAME DRAIN LOCATION FILTER (OPTIONAL) MOUNTING FRAME FIG. 10 0000001029 (Rev.
PAGE 9
EZWS-EDFPBM117K 1/4” O.D. TUBE WATER INLET TO COOLER 3/8” O.D. UNPLATED COPPER TUBE CONNECT COLD WATER SUPPLY LZWS-EDFPBM117K BUILDING WATER INLET Installation Package The components for installation are packed in two separate boxes, regardless of the type of unit being installed. The boxes contain the following: SERVICE STOP (NOT FURNISHED) NOTE: WATER FLOW DIRECTION Box No. 1: Wall Frame(s) Box No.