Installation Sheet

ManualsBrandsElkay ManualsDrinking FountainsElkay 19-1/2" Outdoor Floor Mounted Single Drinking Station - Vandal Resistant Bubbler

PAGE 1 96628C (Rev. SIE - 1/11)

4591_FTN LK4591_FTN

4591 Model Fountains are among the easiest to install Fountains on the

market today. To assure you install these models easily and correctly,

PLEASE READ THESE SIMPLE INSTRUCTIONS BEFORE STARTING THE

INSTALLATION. CHECK YOUR INSTALLATION FOR COMPLIANCE WITH

PLUMBING, ELECTRICAL, AND OTHER APPLICABLE CODES. After install-

ation, leave these instructions with the Fountain for future reference.

Owners Manual

Model 4591

Floor Mount Stone Fountain

ALL SERVICE TO BE PERFORMED BY AN AUTHORIZED SERVICE PERSON

IMPORTANT

1. Water supply 3/8" O.D. unplated copper tube. Waste 1-1/4" IPS. Contractor to supply waste trap and service stop

valve in accordance with local code.

2. Connecting lines to be made of unplated copper and should be thoroughly flushed to remove all foreign matter

before being connected to fountain. This fountain is manufactured in such in manner that it does not in any way

cause taste, odor, color, or sediment problems.

3. Connect fountain to supply line with a shut-off valve and install a 3/8" unplated copper water line between the valve

and the cooler. Remove any burrs from from outside of water line. Push the tubes straight into the fittings until they

reach a positive stop, approximately 3/4" (see figures 1 and 2). DO NOT SOLDER TUBES INSERTED INTO THE

STRAINER AS DAMAGE TO THE O-RINGS MAY RESULT.

4. These products are designed to operate on 20 psig to 105 psig supply line pressure. If inlet pressure is above 105

psig, a pressure regulator must be installed in the supply line. Any damage caused by reason of connecting this

product to supply line pressures lower than 20 psig or higher than 105 psis is not covered by warranty.

IMPORTANT! INSTALLER PLEASE NOTE.

THE GROUNDING OF ELECTRICAL EQUIPMENT SUCH AS TELEPHONE, COMPUTERS, ETC. TO WATER LINES IS A

COMMON PROCEDURE. THIS GROUNDING MAY BE IN THE BUILDING OR MAY OCCUR AWAY FROM THE BUILDING.

THIS GROUNDING CAN CAUSE ELECTRICAL FEEDBACK INTO A FOUNTAIN, CREATING AN ELECTROLYSIS WHICH

CAUSES A METALLIC TASTE OR AN INCREASE IN THE METAL CONTENT OF THE WATER. THIS CONDITION IS

AVOIDABLE BY USING THE PROPER MATERIALS AS INDICATED. ANY DRAIN FITTINGS PROVIDED BY THE

INSTALLER SHOULD BE MADE OF PLASTIC TO ELECTRICALLY ISOLATE THE FOUNTAIN FROM THE BUILDING

PLUMBING SYSTEM.

INSTALLER

Summary of content (4 pages)

PAGE 1
4591_FTN LK4591_FTN Owners Manual Model 4591 Floor Mount Stone Fountain INSTALLER 4591 Model Fountains are among the easiest to install Fountains on the market today. To assure you install these models easily and correctly, PLEASE READ THESE SIMPLE INSTRUCTIONS BEFORE STARTING THE INSTALLATION. CHECK YOUR INSTALLATION FOR COMPLIANCE WITH PLUMBING, ELECTRICAL, AND OTHER APPLICABLE CODES. After installation, leave these instructions with the Fountain for future reference.
PAGE 2
4591_FTN LK4591_FTN ROUGH-IN DRAWING START UP 1. This fountain is to be mounted on a smooth, flat, finished surface with adequate support structure. NOTE: Mounting structure must be capable of supporting 300 lb. load on fountain. 2. Refer to rough-in for plumbing. 3. Install shut-off valve on water supply. (valve not furnished) 4. Locate and install fountain using 3/8" minimum anchor screws or bolts. (screws or bolts not furnished) CAUTION: This fountain is rated for inlet water pressure of 20-105 PSI.
PAGE 3
4591_FTN LK4591_FTN ITEMIZED PARTS LIST ITEM NO. PART NO. DESCRIPTION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 100147140560 100322740560 101570540560 10031C 15013C 170705042830 40048C 40089C 40322C 45659C 45660C 55996C 56092C 55913C 60985551640 60291C 61313C 66346C 70021C 70683C 75588C 75589C Drain Gasket Bubbler Gasket Drain Gasket Regulator Retaining Nut Bubbler Tube Assy. Basin Button Nut - Cover Orifice Assy. Bubbler Bubbler Assy.
PAGE 4
591_FTN LK4591_FTN TROUBLE SHOOTING AND MAINTENANCE Orifice Assy: Mineral deposits on orifice can cause water flow to spurt or not regulate. Mineral deposits may be removed from the orifice with a small round file or small diameter wire. CAUTION: DO NOT file or cut orifice material. Stream Regulator: If orifice is clean, regulate flow as in “STREAM HEIGHT ADJUSTMENT" instructions below. If replacement is necessary, see parts list for correct regulator part number.