Installation Sheet

ManualsBrandsElkay ManualsPlumbingWall Mounted EZH2O Bottle Filling Station with Single Cooler and Filtered Non-Refrigerated in Light Gray Granite Color

1000001717 (Rev. N - 09/18)

Page 1

EMABF8WS*1D EMABFDWS*D LMABF8WS*1D LMABFDWS*D

EMABF8 & LMABF 8 Stations de Remplissage de Bouteille Série et Refroidisseurs

EMABF8 & LMABF8 Serie Botella Bombas y Enfriadores

EMABF8

& LMABF8

Series Bottle Filling Stations & Coolers

INSTALLATION & USE MANUAL

Manual de instalación y uso

Manuel d’installation et utilisation

Summary of content (10 pages)

PAGE 1
EMABF8WS*1D EMABFDWS*D LMABF8WS*1D LMABFDWS*D INSTALLATION & USE MANUAL Manual de instalación y uso Manuel d’installation et utilisation EMABF8 & LMABF8 Series Bottle Filling Stations & Coolers EMABF8 & LMABF8 Serie Botella Bombas y Enfriadores EMABF8 & LMABF 8 Stations de Remplissage de Bouteille Série et Refroidisseurs Page 1 1000001717 (Rev.
PAGE 2
EMABF8WS*1D EMABFDWS*D LMABF8WS*1D LMABFDWS*D Note: Danger! Electric shock hazard. Disconnect power before servicing unit. Nota: peligro! Peligro de descarga eléctrica. Desconecte antes de reparar la unidad. Remarque : Danger ! Risque d'électrocution. Débrancher avant de réparer l'appareil. Pictured is unit only without bottle filler. Uses HFC-134A refrigerant Usa refrigerante HFC-134A Utilise du fluide frigorigéne HFC-134A 18 5 3 21 22 26 27 27 26 19 See Fig.
PAGE 3
9 1/16" 991mm 31" 787mm Fig. 2 Page 3 18 3/8" 467mm A 5" 127mm CL 2 7/16" 63mm 3 1/2" 89mm 4 1/2" 114mm 10" 254mm 11/16" 18mm 2 1/2" 64mm 2 9/16" 65mm 13 7/8" 352mm F 7 1/4" 185mm 1 3/8" 35mm 4 9/16" 116mm E 5 3/4" 146mm FINISHED FLOOR 3 3/16" 82mm 15" 381mm 33" 838mm ORIFICE HEIGHT 31 13/16" 808mm RIM HEIGHT 2 5/8" 67mm * 27" 686mm ADA REQUIREMENT* * 12 5/16" 313mm *ADA REQUIREMENT *REQUISITO DE A.D.A.
PAGE 4
EMABF8WS*1D IMPORTANT ALL SERVICE TO BE PERFORMED BY AN EMABFDWS*D LMABF8WS*1D IMPORTANTE IMPORTANT TODO EL SERVICIO DEBERÁ SER EFECTUADO POR UNA TOUT ENTRETIEN DOIT ÊTRE EFFECTUÉ PAR UN AUTHORIZED SERVICE PERSON PERSONA DE SERVICIO AUTORIZADA HANGER BRACKETS & TRAP INSTALLATION INSTALACIÓN DE FIJADOR DE SUSPENSIÓN Y DEL PURGADOR 1) Remove hanger bracket fastened to back of cooler by removing one (1) screw. 2) Mount the hanger bracket and trap as shown in Figure 2.
PAGE 5
EMABF8WS*1D 34 EMABFDWS*D LMABF8WS*1D PUSH BAR MECHANISM MECANISMO DE BARRA DE EMPUJE MÉCANISME DU BOUTON-POUSSOIR 17 34 30 2 25 31 LMABFDWS*D 19 A 34 1 34 25 17 29 34 16 B 27 C 25 17 17 10 25 34 Fig. 4 Water Valve Mechanism - ADJUSTMENT PROCEDURE: - Turn adjustment screw “Counter-Clockwise” until water flow from bubbler starts. - Turn adjustment screw “Clockwise” until water flow stops, THEN turn an additional 1/2 turn.
PAGE 6
EMABF8WS*1D EMABFDWS*D LMABF8WS*1D 7/16” BOLT HOLES FOR FASTENING UNIT TO WALL UNIT CENTER LINE LMABFDWS*D TOP COVER MOUNTING SCREWS 36 Fig. 6 Fig. 5 BRACKET & SCREWS Fig. 7 Fig. 8 Bottle Filler Installation Instructions 1) Remove two (2) mounting screws with 5/32” Allen wrench holding top cover to Bottle Filler (See Fig. 9). Remove top cover. Note do not discard mounting screws, they will be needed to reinstall top cover. 2) Remove wall mounting plate from Bottle Filler.
PAGE 7
EMABF8WS*1D EMABFDWS*D LMABF8WS*1D LMABFDWS*D BF11 - BF12 PROGRAM SETTING THE CONTROL BOARD VERIFY CONTROL BOARD SOFTWARE 1) To verify the software program of the control board the unit will need to be shut down and restarted. The chiller (if present) does not need to be shut down and restarted. 2) The units lower panel must be open to access the power cord and wall outlet. 3) Shut down the unit by unplugging the power cord from the wall outlet.
PAGE 8
EMABF8WS*1D EMABFDWS*D LMABF8WS*1D 13 LMABFDWS*D 28 4 26 28 Fig. 9 WALL MOUNTING PLATE BOTTLE FILLING UNIT Fig. 10 1000001717 (Rev.
PAGE 9
EMABF8WS*1D EMABFDWS*D LMABF8WS*1D Superseal Fitting Assembly Supersello Accesorio de Montaje Superseal Montage Assemblage LMABFDWS*D OPERATION OF QUICK CONNECT FITTINGS SIMPLY PUSHIN IN SIMPLY PUSH TUBE TO TUBE TOATTACH ATTACH A A TUBE TUBEIS IS SECURED SECURED INPOSITION POSITION IN B PUSH PUSHIN IN COLLET COLLET TORELEASE RELEASE TUBE TUBE TO C PUSHING BEFORE PUSHINGTUBE TUBE IN IN BEFORE PULLING TO PULLING IT IT OUT OUT HELPS HELPS TO RELEASE RELEASE TUBE TUBE Note: Screw the locknut hand tig
PAGE 10
EMABF8WS*1D EMABFDWS*D LMABF8WS*1D LMABFDWS*D PARTS LIST/ LISTA DE PIEZAS/ LISTE DES PIÈCES ITEM NO.