Specification Sheet

ManualsBrandsElkay ManualsPlumbingWall Mounted EZH2O Bottle Filling Station with Single Cooler and Filtered Non-Refrigerated in Light Gray Granite Color

12 5/16"

313mm

FINISHED FLOOR

HANGER BRACKET

1 3/8"

35mm

1 3/8"

35mm

5 3/4"

146mm

5 3/4"

146mm

27"

686mm

ADA

REQUIREMENT

13 7/8"

352mm

18 3/8"

467mm

21 3/8"

543mm

25"

635mm

31"

787mm

5/16" (8mm) DIA. (5 HOLES)

2 1/2"

64mm

3 1/2"

89mm

4 1/2"

114mm

2 7/16"

63mm

127mm

10"

254mm

11/16"

18mm

2 9/16"

65mm

7 1/4"

185mm

6 1/4"

159mm

203mm

1 1/2"

38mm

4 9/16"

116mm

6 3/4"

172mm

178mm

7/16"

11mm

MOUNTING HOLES

(6)

15"

381mm

3 3/16"

82mm

52 1/16"

1323mm

17 7/8"

454mm

3 9/16"

90mm

18 1/2"

471mm

18 7/8"

479mm

31 13/16"

808mm

RIM

HEIGHT

33"

838mm

ORIFICE

HEIGHT

2 5/8"

67mm

ACTIVATION

SENSOR

39 1/16"

991mm

EZH2O

Bottle Filling Station

With Single Filtered Mechanically-Activated Water Cooler

Models LMABF8WS and LMABFDWS

ROUGH-IN DIMENSIONS

2222 Camden Court

Oak Brook, IL 60523

elkay.com

Printed in U.S.A.

NOTICE

This water cooler must be connected to the water supply using a dielectric

coupling. The cooler is furnished with a non-metallic strainer which meets this

requirement. The drain trap which is provided by the installer should also be

plastic to completely isolate the cooler from the building plumbing system.

REDUCE HEIGHT BY 3 INCHES FOR INSTALLATION OF CHILDRENS ADA COOLER

Job Name: ____________________________________

Model: _______________________ Qty. ____________

Contact: ______________________________________

Approval Signature: _____________________________

Notes:

LEGEND:

A = Recommended Water Supply location. Shut-off Valve (not furnished) to accept

3/8” O.D. unplated copper tube. Up to 3” (76mm) maximum out from wall.

B = Recommended Waste Outlet location. To accommodate 1-1/4” nominal drain.

Drain stub 2” (51mm) out from wall.

C = 1-1/4” Trap (not furnished).

D = Electrical Supply (3) Wire Recessed Box Duplex Outlet.

E = Insure proper ventilation by maintaining 6” (152mm) minimum clearance from cabinet

louvers to wall.

F = 7/16” (11mm) Bolt Holes for fastening to wall.

**New Installations Must Use Ground Fault Circuit Interrupter (GFCI).

IMPORTANT!

INSTALLER PLEASE NOTE

This water cooler has been designed and built to provide water to the user which

has not been altered by materials in the cooler waterways. The grounding of

electrical equipment such as telephone, computers, etc., to water lines is a

common procedure. This grounding may be in the building but may also occur

away from the building. This grounding can cause electrical feedback into a

water cooler creating an electrolysis which creates a metallic taste or causes

an increase in the metal content of the water. This condition is avoidable by

installing the cooler using the proper materials as shown below.

Bottle Filler unit will mount on bracket attached to wall by 6 holes (as shown).

Water and electrical will connect through pre-punched hole in basin.