Installation Sheet

ManualsBrandsElkay ManualsDrinking FountainsFiltered 8 GPH EZH2O ADA Stainless Steel Bi-Level Drinking Fountain with Bottle Filling Station

EMABFTL8WS*1E EMABFTLDDWS*E LMABFTL8WS*1E LMABFTLDDWS*E

1000001718 (Rev. M - 01/19)

Page 1

EMABF8TL & LMABF8TL Stations de Remplissage de Bouteille Série et Refroidisseurs

EMABF8TL & LMABF8TL Serie Botella Bombas y Enfriadores

EMABF8TL

& LMABF8TL

Series Bottle Filling Stations & Coolers

INSTALLATION, CARE & USE MANUAL

Manual de Instalación, Cuidado y Utilización

Manuel d’installation/entretien/utilisation

Summary of content (10 pages)

PAGE 1
EMABFTL8WS*1E EMABFTLDDWS*E LMABFTL8WS*1E LMABFTLDDWS*E INSTALLATION, CARE & USE MANUAL Manual de Instalación, Cuidado y Utilización Manuel d’installation/entretien/utilisation EMABF8TL & LMABF8TL Series Bottle Filling Stations & Coolers EMABF8TL & LMABF8TL Serie Botella Bombas y Enfriadores EMABF8TL & LMABF8TL Stations de Remplissage de Bouteille Série et Refroidisseurs Page 1 1000001718 (Rev.
PAGE 2
EMABFTL8WS*1E EMABFTLDDWS*E LMABFTL8WS*1E LMABFTLDDWS*E Note: Danger! Electric shock hazard. Disconnect power before servicing unit. Nota: peligro! Peligro de descarga eléctrica. Desconecte antes de reparar la unidad. Remarque : Danger ! Risque d'électrocution. Débrancher avant de réparer l'appareil. Pictured is unit only without bottle filler. Uses HFC-134A refrigerant Usa refrigerante HFC-134A Utilise du fluide frigorigéne HFC-134A 5 3 8 18 3 23 24 30 30 12 25 26 4B 2 20 See Fig.
PAGE 3
2 9/16" 65mm F 5" 127mm 4 9/16" 116mm 7" 178mm Fig. 2 Page 3 10" 254mm 2 7/16" 63mm 11/16" 18mm B 6 1/4" 159mm CL 4 1/2" 114mm 3 1/2" 89mm 1 3/8" 1 3/8" 35mm 35mm 5 3/4" 146mm 18 1/16" 459mm 5 3/4" 146mm E 20 1/8" 511mm 18 3/4" 476mm F A D 25 1/8" 638mm 5/16" (8mm) DIA.
PAGE 4
EMABFTL8WS*1E EMABFTLDDWS*E LMABFTL8WS*1E LMABFTLDDWS*E IMPORTANT ALL SERVICE TO BE PERFORMED BY AN AUTHORIZED SERVICE PERSON IMPORTANTE TODO EL SERVICIO DEBERÁ SER EFECTUADO POR UNA PERSONA DE SERVICIO AUTORIZADA IMPORTANT TOUT ENTRETIEN DOIT ÊTRE EFFECTUÉ PAR UN REPRÉSENTANT AUTORISÉ HANGER BRACKETS & TRAP INSTALLATION INSTALACIÓN DE FIJADOR DE SUSPENSIÓN Y DEL PURGADOR INSTALLATION DU SIPHON ET DU SUPPORT DE SUSPENSION 1) Remove hanger bracket fastened to back of cooler by removing one (1) scre
PAGE 5
EMABFTL8WS*1E 29 EMABFTLDDWS*E LMABFTL8WS*1E LMABFTLDDWS*E PUSH BAR MECHANISM MECANISMO DE BARRA DE EMPUJE MÉCANISME DU BOUTON-POUSSOIR 19 29 19 34 20 27 2 A 1 29 35 29 27 19 33 19 16 B 29 30 C 25 29 10 19 Water Valve Mechanism - ADJUSTMENT PROCEDURE: - Turn adjustment screw “Counter-Clockwise” until water flow from bubbler starts. - Turn adjustment screw “Clockwise” until water flow stops, THEN turn an additional 1/2 turn.
PAGE 6
EMABFTL8WS*1E EMABFTLDDWS*E LMABFTL8WS*1E 7/16” BOLT HOLES FOR FASTENING UNIT TO WALL UNIT CENTER LINE TOP COVER LMABFTLDDWS*E MOUNTING SCREWS 41 Fig. 7 Fig. 6 BRACKET & SCREWS Fig. 8 Fig. 9 Bottle Filler Installation Instructions 1) Remove two (2) mounting screws with 5/32” Allen wrench holding top cover to Bottle Filler (See Fig. 9). Remove top cover. Note do not discard mounting screws, they will be needed to reinstall top cover. 2) Remove wall mounting plate from Bottle Filler.
PAGE 7
EMABFTL8WS*1E EMABFTLDDWS*E LMABFTL8WS*1E LMABFTLDDWS*E BF11 - BF12 PROGRAM SETTING THE CONTROL BOARD VERIFY CONTROL BOARD SOFTWARE 1) To verify the software program of the control board the unit will need to be shut down and restarted. The chiller (if present) does not need to be shut down and restarted. 2) The units lower panel must be open to access the power cord and wall outlet. 3) Shut down the unit by unplugging the power cord from the wall outlet.
PAGE 8
EMABFTL8WS*1E EMABFTLDDWS*E LMABFTL8WS*1E LMABFTLDDWS*E 13 28 13 32 31 4A 4B 13 13 8 Fig. 10 Fig. 11 WALL MOUNTING PLATE BOTTLE FILLING UNIT Fig. 12 1000001718 (Rev.
PAGE 9
EMABFTL8WS*1E EMABFTLDDWS*E LMABFTL8WS*1E LMABFTLDDWS*E Superseal Fitting Assembly Supersello Accesorio de Montaje Superseal Montage Assemblage OPERATION OF QUICK CONNECT FITTINGS SIMPLY PUSHIN IN SIMPLY PUSH TUBE TO TUBE TOATTACH ATTACH A A TUBE TUBEIS IS SECURED SECURED INPOSITION POSITION IN PUSH PUSHIN IN COLLET COLLET TORELEASE RELEASE TUBE TUBE TO B C PUSHING BEFORE PUSHINGTUBE TUBE IN IN BEFORE PULLING TO PULLING IT IT OUT OUT HELPS HELPS TO RELEASE RELEASE TUBE TUBE Note: Screw the locknu
PAGE 10
EMABFTL8WS*1E EMABFTLDDWS*E LMABFTL8WS*1E LMABFTLDDWS*E PARTS LIST/ LISTA DE PIEZAS/ LISTE DES PIÈCES ITEM NO.