Installation Sheet

ManualsBrandsElkay ManualsPopular CollectionsElkay EZH20 17-7/8" Wall Mounted Retrofit Single Station Hands Free Bottle Filler Combo

Page 1 1000001719 (Rev. C - 11/14)

EMABFWS*RF*1A LMABFWS*RF*1A

EMABFWS-RF LMABFWS-RF Retrot Bottle Filling Station

EMABF / LMABF Bottle Fillers are among the easiest to install on the market today.

To insure you install these models easily and correctly, PLEASE READ THESE

SIMPLE INSTRUCTIONS BEFORE STARTING THE INSTALLATION. CHECK

YOUR INSTALLATION FOR COMPLIANCE WITH PLUMBING, ELECTRICAL, AND

OTHER APPLICABLE CODES. After installation, leave these instructions with the

Fountain for future reference.

IMPORTANT

THIS IS AN INDOOR APPLICATION ONLY.

ALL SERVICE TO BE PERFORMED BY AN

AUTHORIZED SERVICE PERSON.

IMPORTANT! INSTALLER PLEASE NOTE.

THE GROUNDING OF ELECTRICAL EQUIPMENT SUCH AS TELEPHONE, COMPUTERS, ETC. TO WATER

LINES IS A COMMON PROCEDURE. THIS GROUNDING MAY BE IN THE BUILDING OR MAY OCCUR AWAY

FROM THE BUILDING. THIS GROUNDING CAN CAUSE ELECTRICAL FEEDBACK INTO A FOUNTAIN, CREAT-

ING AN ELECTROLYSIS WHICH CAUSES A METALLIC TASTE OR AN INCREASE IN THE METAL CONTENT

OF THE WATER. THIS CONDITION IS AVOIDABLE BY USING THE PROPER MATERIALS AS INDICATED. ANY

DRAIN FITTINGS PROVIDED BY THE INSTALLER SHOULD BE MADE OF PLASTIC TO ELECTRICALLY ISO-

LATE THE FOUNTAIN FROM THE BUILDING PLUMBING SYSTEM. WE SUGGEST THAT THE BOTTLE FILLING

STATION AND WATER COOLER BE PROTECTED BY A GROUND FAULT CIRCUIT INTERRUPTER (GFCI).

INSTALLER

TOOLS REQUIRED

BUT NOT PROVIDED:

SAFETY GLASSES

GLOVES

ELECTRIC DRILL

3/4” WRENCH OR CRESCENT

WRENCH

UTILITY KNIFE

TAPE MEASURE

PENCIL

5/32” ALLEN WRENCH

Installation/Care/Use Manual

Summary of content (15 pages)

PAGE 1
EMABFWS*RF*1A LMABFWS*RF*1A Installation/Care/Use Manual EMABFWS-RF LMABFWS-RF Retrofit Bottle Filling Station IMPORTANT THIS IS AN INDOOR APPLICATION ONLY. ALL SERVICE TO BE PERFORMED BY AN AUTHORIZED SERVICE PERSON. TOOLS REQUIRED BUT NOT PROVIDED: SAFETY GLASSES GLOVES ELECTRIC DRILL 3/4” WRENCH OR CRESCENT WRENCH UTILITY KNIFE TAPE MEASURE PENCIL 5/32” ALLEN WRENCH IMPORTANT! INSTALLER PLEASE NOTE. THE GROUNDING OF ELECTRICAL EQUIPMENT SUCH AS TELEPHONE, COMPUTERS, ETC.
PAGE 2
EMABFWS*RF*1A LMABFWS*RF*1A WATER COOLER PREPARATION NOTE: • On Two Level Models, the Bottle Filling Unit MUST be mounted on the higher unit: • Two Level Standard Models; high unit is on Left Hand(LH) side. • Two Level Reverse Models; high unit is on Right Hand(RH) side. 1) Remove Front Panel • Remove lower front panel of water cooler by removing the four (4) screws, two at top and two at bottom. On Two Level Models, remove both front panels. • WARNING: Before proceeding.
PAGE 3
EMABFWS*RF*1A LMABFWS*RF*1A WATER COOLER PREPARATION 4) Remove Bubbler Water Line • Disconnect water line from bubbler. Remove Bubbler Water Line 5) Lift and Remove Basin. • Remove basin assembly by lifting straight up, disconnecting the drain line from the P-trap. Lift and Remove Basin. 6) Assemble Drain hardware. • Remove the protective covering from the basin. • Attach the new drain hardware onto the new basin. Exchange Drain hardware. 7) Exchange Bubbler hardware.
PAGE 4
EMABFWS*RF*1A LMABFWS*RF*1A EWF3000 WATERSENTRY PLUS FILTER INSTALLATION WARNINGS: • Do not use with water that is microbiologically unsafe or of unknown quality. For potable water only. • Do not use with a hot water supply. Rated for water temperature: 33°-100°F(2°-38°C) • Water line pressure must not exceed 100psi(690kPa). Use an inline water pressure regulator before filter to limit maximum pressure. Rated water supply pressure: 20-100psi(138-690kPa).
PAGE 5
EMABFWS*RF*1A LMABFWS*RF*1A EWF3000 WATERSENTRY PLUS FILTER INSTALLATION 3) Mount Filter Head Assembly Mount Filter Head Assembly into Cooler. Unit with single supplied screw: • Single Level Models • Mount on inside of left panel butted up against top lip. • NOTE: The filter bracket is mounted with a single screw. Single Level Models • Two Level Models • Mount in left hand cooler on the inside of the right panel, butted up against the top lip. • NOTE: The filter bracket is mounted with a single screw.
PAGE 6
EMABFWS*RF*1A LMABFWS*RF*1A RE-PLUMBING SINGLE STATION WATER CIRCUITS (NON-FILTER) CAUTION: • This procedure MUST be performed on ALL SINGLE ELKAY WATER COOLERS or the bottle filling unit WILL NOT perform properly! • When disconnecting water lines use a container to catch any water running out of the lines. 1) Connect Water Supply: • Remove the in-line strainer outlet tube from the Regulator Inlet.
PAGE 7
EMABFWS*RF*1A LMABFWS*RF*1A RE-PLUMBING SINGLE STATION WATER CIRCUITS (WITH FILTER) CAUTION: • This procedure MUST be performed on ALL SINGLE ELKAY WATER COOLERS or the bottle filling unit WILL NOT perform properly! • When disconnecting water lines use a container to catch any water running out of the lines. 1) Connect Water Supply: IN-LINE STRAINER • Remove the in-line strainer outlet tube from the Regulator Inlet.
PAGE 8
EMABFWS*RF*1A LMABFWS*RF*1A RE-PLUMBING TWO LEVEL STATION WATER CIRCUITS (NON-FILTER) CAUTION: • This procedure MUST be performed on ALL TWO LEVEL ELKAY WATER COOLERS or the bottle filling unit WILL NOT perform properly! • When disconnecting water lines use a container to catch any water running out of the lines.
PAGE 9
EMABFWS*RF*1A LMABFWS*RF*1A RE-PLUMBING TWO LEVEL STATION WATER CIRCUITS (WITH FILTER) CAUTION: • This procedure MUST be performed on ALL TWO LEVEL ELKAY WATER COOLERS or the bottle filling unit WILL NOT perform properly! • When disconnecting water lines use a container to catch any water running out of the lines. 1) Connect Water Supply: • In the left hand unit,connect the Filter outlet using 1/4” poly tubing to the Evaporator 1/4” copper inlet using the supplied 1/4” quick connect fitting.
PAGE 10
EMABFWS*RF*1A LMABFWS*RF*1A BASIN ASSEMBLY PREPARATION 1) Connect Water Line • Connect water line from Regulator to Bubbler. Connect Water Line 2) Install New Basin Assembly • Reposition Basin Assembly (Basin with Drain and Bubbler hardware) back onto the cooler. • Reattach drain line to P-trap and tighten. Reattach drain line to P-trap 3) Fasten Basin Assembly in place. • Insert and retighten the 8 screws, four per side. Fasten Basin Assembly in place. 1000001719 (Rev.
PAGE 11
EMABFWS*RF*1A LMABFWS*RF*1A BOTTLE FILLER GASKET Fig. 6 Fig. 7 Page 11 1000001719 (Rev.
PAGE 12
EMABFWS*RF*1A LMABFWS*RF*1A BOTTLE FILLER INSTALLATION TOP COVER MOUNTING SCREWS 7/16” BOLT HOLES FOR FASTENING UNIT TO WALL UNIT CENTER LINE Fig. 8 Fig. 9 WALL MOUNTING PLATE BOTTLE FILLING UNIT Fig. 10 BOTTLE FILLER INSTALLATION 1) Remove two (2) mounting screws with 5/32” Allen wrench holding top cover to Bottle Filler (See Fig. 8). Remove top cover. Note do not discard mounting screws, they will be needed to reinstall top cover. 2) Remove wall mounting plate from Bottle Filler.
PAGE 13
EMABFWS*RF*1A LMABFWS*RF*1A BF11 PROGRAM SETTING THE CONTROL BOARD VERIFY CONTROL BOARD SOFTWARE 1) To verify the software program of the control board the unit will need to be shut down and restarted. The chiller (if present) does not need to be shut down and restarted. 2) The units lower panel must be open to access the power cord and wall outlet. 3) Shut down the unit by unplugging the power cord from the wall outlet. 4) Restart the unit by plugging the power cord back into the wall outlet.
PAGE 14
EMABFWS*RF*1A LMABFWS*RF*1A RESET BUTTON FIVE PIN CONNECTOR FOUR PIN CONNECTOR PIGGY BACK TERMINAL ON POWERCORD MAIN BOARD WHITE I.R. BOARD RED SOLENOID GND LED BOARD VIOLET YELLOW PROTECTIVE CAP (NOT USED) GREEN GROUND CONNECTOR FROM POWER CORD NEUTRAL WHITE RIBBED LINE VOLTAGE SMOOTH BLACK POWER CORD WIRING DIAGRAM 120 VOLT SINGLE & TWO LEVEL Fig. 11 3 2 2 2 FILTER PARTS LIST (See Fig. 12) 1 ITEM NO. PART NO. 1 2 51300C 98926C 3 0000000746 DESCRIPTION Filter Assy-3000 Gal.
PAGE 15
EMABFWS*RF*1A LMABFWS*RF*1A REPLACEMENT PART KITS PART NO.