Use and Care Manual

ManualsBrandsElkay ManualsDrinking FountainsFiltered 8GPH EZH2O Integral SwirlFlo Stainless Steel Drinking Fountain with Bottle Filling Station

ERPBD28WSC LRPBD2_8WSC

0000001030 (Rev. G - 01/18)

Page 1

SWIRLFLO

Refrigerated fountains with FLEXI-GUARD

and EZH

Bottle Filler

Review these instructions before beginning installation. Be sure that installation

conforms to all plumbing, electrical and other applicable codes.

When installation is complete, ensure these instructions are left in the plastic bag

provided inside the installed unit for future reference.

Service to be performed by authorized service personnel only.

INSTALLER

NOTE: It is common practice to ground electrical hardware such as telephones, computers and other devices

to available water lines. This can, however, cause electrical feedback in the plumbing circuit, which

results in an “electrolysis” effect occurring in the fountain. This may result in water which has a

metallic taste to it or has a noticeable increase in the metallic content of the water.

When inspecting plumbing circuit, remember the line may be grounded some distance from the

installation, and may occur outside the building or area in which the unit is being installed.

This condition can be avoided (in most cases) by using recommended materials during installation.

Any drain ttings provided by the installer should be made of plastic which will electronically isolate

the fountain from the remainder of the building’s plumbing circuits.

EZWS-ERPBM28K

LZWS-LRPBM28K

INSTALLATION & USE MANUAL

Summary of content (8 pages)

PAGE 1
ERPBD28WSC LRPBD2_8WSC INSTALLATION & USE MANUAL SWIRLFLO® Refrigerated fountains with FLEXI-GUARD® and EZH2O® Bottle Filler LZWS-LRPBM28K EZWS-ERPBM28K INSTALLER Review these instructions before beginning installation. Be sure that installation conforms to all plumbing, electrical and other applicable codes. When installation is complete, ensure these instructions are left in the plastic bag provided inside the installed unit for future reference.
PAGE 2
0000001030 (Rev. G - 01/18) Figure 1 - Rough-in Dimensions Page 2 18 11/16" 474mm 44 3/4" 1137mm FINISHED FLOOR ELECTRICAL INLET 3/8" O.D. COPPER TUBE WATER INLET ON CHILLER.
PAGE 3
ERPBD28WSC LRPBD2_8WSC REQUIRED TOOLS AND MATERIALS TO BUBBLER TO BOTTLE FILLER These tables show special tools and/or additional materials (not provided) which are necessary to complete installation of these units: 13 12 Special Tools Item 12 15 14 33 CHILLER OUTLET Additional Materials Not Included Item Description CHILLER INLET 13 15 1 Unplated copper inlet pipe 1 2 Service Stop/Shut-off Valve 1 3 90° 1-1/4” Drain Line 1 4 1-1/4” Tee Drain Line 1 3.
PAGE 4
ERPBD28WSC LRPBD2_8WSC 8. Install reset switch for bottle filler (Fig 4). Connect the switch wire to the extension wire on the back of the bottle filler. Wrap up the excess cord. 26 Reset Switch 9. Attach waste tubes (1-1/4” O.D.) to 1-1/4” O.D. slip trap. Trap on the bottle filler side must be 1-1/2” O.D. (provided by others). 20 10. Make final water supply connections. 18 11. These products are designed to operate on 20-105 PSI supply line pressure.
PAGE 5
ERPBD28WSC LRPBD2_8WSC 11 See Fig. 6 2 9 See Fig. 6 10 3 19 5 12 22 4 Figure 7 - Fountain Body Assembly 22 6 7 8 21 Figure 8 - Push Button Assembly Page 5 0000001030 (Rev.
PAGE 6
ERPBD28WSC LRPBD2_8WSC BF11 - BF12 PROGRAM SETTING THE CONTROL BOARD VERIFY CONTROL BOARD SOFTWARE 1) To verify the software program of the control board the unit will need to be shut down and restarted. The chiller (if present) does not need to be shut down and restarted. 2) The units lower panel must be open to access the power cord and wall outlet. 3) Shut down the unit by unplugging the power cord from the wall outlet. 4) Restart the unit by plugging the power cord back into the wall outlet.
PAGE 7
ERPBD28WSC LRPBD2_8WSC MOUNTING FRAME MAIN PANEL REMOTE CHILLER DRAIN LOCATIONS FILTER (OPTIONAL) MOUNTING FRAME Fig. 9 3 2,3 LOWER PANEL 2,3 3/8” Water Inlet WATERSENTRY® PLUS FILTER PARTS LIST (See Fig. 10) 1 ITEM NO. 1 2 3 PART NO. 51300C 98926C 51469C DESCRIPTION Filter Assy-3000 Gal. Kit-Filter Head Fittingsk-includes John Guest Fittings Assy-Filter & Brkt includes Fltr Head/Mtg Bkt/ John Guest Fittings/Screws Fig. 10 Page 7 0000001030 (Rev.
PAGE 8
ERPBD28WSC 1/4” O.D. TUBE WATER INLET TO COOLER 3/8” O.D. UNPLATED COPPER TUBE CONNECT COLD WATER SUPPLY LRPBD2_8WSC Installation Package BUILDING WATER INLET The components for installation are packed in three separate boxes, regardless of the type of unit being installed. The boxes contain the following: SERVICE STOP (NOT FURNISHED) NOTE: WATER FLOW DIRECTION Box No. 1: Wall Frame(s) Box No. 2: Remote Chiller, ECH8 Box No.