Installation Instructions

ManualsBrandsElkay ManualsPopular CollectionsElkay EZH2O Refrigerated Bottle Filling Station with Hands Free Operation, and Filter

98526C (Rev. C - 1/13)Page 1

WaterSentry

Plus Retro Bottle Filler and Water Cooler.

7. Turn on water supply and hold open the bubbler on

cooler until approximately 1 gallon of water is dis-

pensed.This flushing procedure purges air and fine

carbon particles from the filter. When 1 gallon of water

has been purged through the cooler, carefully inspect

all water connections for leaks.

FOR COMMERCIAL USE ONLY

These filter kits are designed to be used with the following

Elkay product.

1. LZS

NOTICE: Do not use with water that is microbiologically

unsafe or of unknown quality without adequate

disinfection before or after the system.

Filter must be used with filter monitor for 3000

gallon rating

General Installation Instructions

1. These filter kits must be installed in compliance with all

state and local laws and regulations governing the

installation and use of this product. Maximum inlet

water temperature 100°F (38°C).

2. Mount filter head in a suitable location, using the filter

mounting bracket and screws supplied. Allow enough

room under the filter head for installation and removal of

filter cartridge (13" minimum).

3. Connect the cold water supply to the filter through a

shut-off valve and 3/8" O.D. tubing (supplied by the

installer). For ease of servicing, the shut-off valve

should be located within easy reach of the filter.

NOTE: The inlet and outlet fitting supplied as

part of the filter head are John Guest Superseal

fittings that accept 3/8" O.D. tubing on the filter

inlet and 1/4" O.D. tubing on the outlet. They may

be used with copper, stainless steel, or semirigid

nylon or polypropylene tubing, with a rated working

pressure equal or greater than encountered in

application. Do not use soft or braided tubing.

4. CAUTION: If supply pressure will ever exceed

100 psi, install a pressure regulator to limit the

inlet pressure to the filter to 100 psi or below.

DO NOT ATTACH HOT WATER LINE TO FILTER.

To make connections on the filter head, loosen locknut.

Push the tube end past both o-rings to a positive stop in

the filter head recess - approx. 1", locknut may have to

be backed out a little more. Screw the locknut hand tight

to seal (See Fig. 1). Ends of tubing must be cut square

and free of burrs and sharp ends that could cut or nick

the o-rings.

5. Connect the outlet of the filter to the inlet of the union

using the 1/4" O.D. poly tubing and 1/4" union supplied.

6. Remove filter from carton, remove protective cap, attach

filter to filter head by firmly inserting into head and

rotating filter clockwise.

FIG. 2

FIG. 1

See Note 4: Screw the locknut hand tight to seal

Filter Replacement*

1.Turn inlet water valve off.

2.Open bubbler or activate the electric eye to relieve pressure

build-up in the system.

3.Remove filter from head by rotating filter counterclock

wise.

4.Remove new filter from carton, remove protective cap;

cap may be placed on old filter to reduce the chance of

water spilling from filter housing.

5.Attach filter to filter head by firmly inserting into head

and rotating filter clockwise.

WaterSentry

Plus In Wall Bottle Filler .

7. Turn on water supply and activate the electric eye on

In Wall Bottle Filler until approximately 1 gallon of

water is dispensed. Please note that the electric eye

activation times out at 30 seconds and will need to

be activate repeatedly until one gallon has been

passed. This flushing procedure purges air and fine

carbon particles from the filter. When 1 gallon of water

has been purged through the bottle filler, carefully

inspect all water connections for leaks.

FILTER KIT

EWF3000 Watersentry

Plus KIT

(Lead, Aesthetic Chlorine Taste & Odor & Particulate Class I Reduction)

FOR COMMERCIAL USE ONLY

The Elkay

WaterSentry

Plus is certified by WQA to NSF/ANSI Standard 42 and 53 for the

reduction of

Aesthetic Chlorine, Taste and Odor, Particulate Class I, and Lead, as verified and

substantiated by test data.

Summary of content (4 pages)

PAGE 1
FILTER KIT EWF3000 Watersentry® Plus KIT (Lead, Aesthetic Chlorine Taste & Odor & Particulate Class I Reduction) FOR COMMERCIAL USE ONLY The Elkay® WaterSentry® Plus is certified by WQA to NSF/ANSI Standard 42 and 53 for the reduction of Aesthetic Chlorine, Taste and Odor, Particulate Class I, and Lead, as verified and substantiated by test data. ® FOR COMMERCIAL USE ONLY These filter kits are designed to be used with the following Elkay product. 1.
PAGE 2
NOTE: The filter head contains an automatic shut-off valve that stops the flow of water, if the filter is removed inadvertently without shutting off the incoming water. RATED OPERATING CONDITIONS Pressure (Max.) 105 PSI (7.4 Kg/cm2) Pressure (Min.) 20 PSI (1.4 Kg/cm2) Flow Rate 1.5 GPM Temperature (Max.) 120° F (50° C) Temperature (Min.) 40° F (5° C) NOTE: Performance will vary depending on local water conditions. Table A REPLACEMENT FILTER Filter Part No.
PAGE 3
In Wall Bottle Filler & Remote Chiller CHILLED WATER BOTTLE FILLER WATER "IN" TO REMOTE CHILLER 1/4" (6mm) UNION (SUPPLIED) 1/4" (6mm) O.D. TUBING (SUPPLIED) FROM COLD WATER SUPPLY O.D. TUBE 3/8" (10 mm) INSTALLATION WHEN USED WITH WATER CHILLER PLUMB FILTER OUTLET DIRECTLY TO IN WALL BOTTLE FILLER IF NO CHILLER IS USED See page 4 for replacement information. Page 3 98526C (Rev.
PAGE 4
NOTICE To receive maximum benefit from your ELKAY WaterSentry® Plus filters, note the installation dates below and change according to the following guidelines. ELKAY Part No. 51300C WaterSentry® Plus -- Lead Reduction Filter Change every 3,000 gallons as indicated by the filter monitor, or once a year -- whichever occurs first.