Installation Sheet

ManualsBrandsElkay ManualsPopular CollectionsElkay EZH2O Surface Mount Bottle Filling Station with Hands Free Operation, and Filter

98764C (Rev. J - 08/17)

EZWSSM-1A, EZWSSMJO-2A, LZWSSM-1A, LZWSSMJO-2A

Page 1

Installation and Use Manual

ezH2O

Surface Mount Bottle Filling Station

Model

LZWSSM

Warnings

1. Use with clean, clear, fresh potable drinking water only! Do not use with water that is microbiologically

unsafe or of unknown quality without adequate disinfection before the system.

2. Connect Power Cord only to a grounded three prong electrical outlet with electrical power that:

a. MUSTberatedforthisproductasspeciedonproductdatalabel.

b. MUST have over-current protection (e.g. Fuse, Breaker).

c. MUST have Ground Fault Circuit Interrupt protection (GFCI).

d. These products are designed to operate on 20 to 105 PSI supply line pressure. If inlet pressure is

above 105 PSI, a pressure regulator must be installed in supply line. Any damage caused

by reason of connecting this product to supply line pressure lower than 20 PSI or higher than

105 PSI is not covered by warranty.

To assure you install this model easily and correctly, PLEASE READ THESE

SIMPLE INSTRUCTIONS BEFORE STARTING THE INSTALLATION. CHECK

YOUR INSTALLATION FOR COMPLIANCE WITH ALL PLUMBING, ELECTRICAL

AND OTHER APPLICABLE CODES. FOLLOW ALL WARNINGS AND CAUTIONS

CAREFULLY. After installation, leave these instructions with the customer for future

reference.

Installer

IMPORTANT

THIS IS AN INDOOR APPLICATION ONLY!

ALL SERVICE TO BE PERFORMED BY AN

AUTHORIZED SERVICE PERSONNEL.

TOOLS/ITEMS REQUIRED

BUT NOT SUPPLIED

- SERVICE STOP VALVE WITH 3/8"

COMPRESSION OUTLET

- FASTENERS FOR WALL TYPE (8 REQ’D.)

- SLIP JOINT DRAIN UNION OR

COMPRESSION CLAMP

- 5/32" HEX-WRENCH

Summary of content (7 pages)

PAGE 1
EZWSSM-1A, EZWSSMJO-2A, LZWSSM-1A, LZWSSMJO-2A Installation and Use Manual ezH2O® Surface Mount Bottle Filling Station IMPORTANT THIS IS AN INDOOR APPLICATION ONLY! ALL SERVICE TO BE PERFORMED BY AN AUTHORIZED SERVICE PERSONNEL. TOOLS/ITEMS REQUIRED BUT NOT SUPPLIED - SERVICE STOP VALVE WITH 3/8" COMPRESSION OUTLET - FASTENERS FOR WALL TYPE (8 REQ’D.
PAGE 2
EZWSSM-1A, EZWSSMJO-2A, LZWSSM-1A, LZWSSMJO-2A ROUGH-IN EZWSSM, EZWSSMJO, LZWSSM, LZWSSMJO 17 15/16" 455mm 7" 7" 178mm 178mm D 8 3/16" 208mm 5 3/8" 136mm D D ACTIVATION SENSOR 9 1/2" 241mm D OPTIONAL (3 PL) 25 7/16" 647mm B 12" 305mm DRAIN TRAP CUSTOMER SUPPLIED 2 7/8" 73mm A D D 46 7/16" 1179mm 3 1/16" 78mm 8 7/8" 225mm 6 1/4" 159mm 28" 712mm 40 1/4" 1022mm 33 1/2" 850mm 34 7/16" 875mm 32 15/16" 837mm 120V POWERCORD (18" MIN.
PAGE 3
EZWSSM-1A, EZWSSMJO-2A, LZWSSM-1A, LZWSSMJO-2A INSTALLATION INSTRUCTIONS Pre-Installation (reference Rough-In, Fig. 1, Page 2) 1. Ensure Wall is structurally sound to bear the loads imparted by the ezH2O® Surface Mount Bottle Filling Station (On-Wall Bottle Filler). If necessary, install a Wall Support Carrier (not supplied). 2. Ensure Water Supply Line and Drain Line are sized and located as specified the Rough-in diagram. 3.
PAGE 4
EZWSSM-1A, EZWSSMJO-2A, LZWSSM-1A, LZWSSMJO-2A Plumbing Connections • Ensure lines and ports remain clean and free of contaminants during assembly. • Purge each component if necessary. • To ensure quick-connect connections seal properly, follow instructions per Figure 2, Page 2. Connect Plumbing Lines 1. Connect water supply line to unit: 1.1. Filtered Units: Connect the 3/8" O.D. copper tube (supplied factory attached on the Filter Head inlet port) to the 3/8" Compression end of Service Stop Valve. 1.2.
PAGE 5
EZWSSM-1A, EZWSSMJO-2A, LZWSSM-1A, LZWSSMJO-2A BF9 PROGRAM SETTING THE CONTROL BOARD VERIFY CONTROL BOARD SOFTWARE SETTING UNIT TYPE 1) To verify the software program of the control board the unit will 1) Depress the program button for approximately 2 seconds need to be shut down and restarted. The chiller (if present) does not until the display changes then release. The display will need to be shut down and restarted.
PAGE 6
EZWSSM-1A, EZWSSMJO-2A, LZWSSM-1A, LZWSSMJO-2A BF11 - BF12 PROGRAM SETTING THE CONTROL BOARD VERIFY CONTROL BOARD SOFTWARE 1) To verify the software program of the control board the unit will need to be shut down and restarted. The chiller (if present) does not need to be shut down and restarted. 2) The units lower panel must be open to access the power cord and wall outlet. 3) Shut down the unit by unplugging the power cord from the wall outlet.
PAGE 7
EZWSSM-1A, EZWSSMJO-2A, LZWSSM-1A, LZWSSMJO-2A WATERSENTRY® PLUS FILTER PARTS LIST (See FIG. 3) ITEM NO. PART NO. 1 2 3 4 51300C 98926C 51294C 70792C DESCRIPTION Filter Assy - 3000 Gallon Kit-Filter Head includes John Guest Fittings Filter Head Assy. Screw-#8-18 X .75 PHHL 4 3 2 3/8” Water Inlet 2 Bottom Cover Power Cord Clamp 1 Bushing Screw 220V POWER CORD DETAIL FIG. 4 WATER FILTER EXPLODED VIEW FIG. 3 REPLACEMENT PART KITS PART NO.