Installation Sheet

ManualsBrandsElkay ManualsPopular CollectionsElkay EZH20 36-1/8" Wall Mounted Bi-Level Station Hands Free Bottle Filler Combo - Cooler Operated and Vandal Resistant Bubbler

VRCGRNTLDWS*C VRCGRNTL8WS*1C LVRCGRNTLDWS*C LVRCGRNTL8WS*1C

1000001742 (Rev. N - 01/19)

Page 1

EZH2O

Bottle Filling Station and Cooler

INSTALLATION & USE MANUAL

Station de remplissage de bouteille EZH2O

et refroidisseur

Estación de llenado de botella EZH2O

y enfriador

Manual de instalación y uso

Manuel d’installation et d’utilisation

Summary of content (10 pages)

PAGE 1
VRCGRNTLDWS*C VRCGRNTL8WS*1C LVRCGRNTLDWS*C LVRCGRNTL8WS*1C INSTALLATION & USE MANUAL Manual de instalación y uso Manuel d’installation et d’utilisation EZH2O® Bottle Filling Station and Cooler Estación de llenado de botella EZH2O® y enfriador Station de remplissage de bouteille EZH2O® et refroidisseur Page 1 1000001742 (Rev.
PAGE 2
VRCGRNTLDWS*C VRCGRNTL8WS*1C LVRCGRNTLDWS*C LVRCGRNTL8WS*1C Note: Danger! Electric shock hazard. Disconnect power before servicing unit. Nota: peligro! Peligro de descarga eléctrica. Desconecte antes de reparar la unidad. Remarque : Danger ! Risque d'électrocution. Débrancher avant de réparer l'appareil. Pictured is unit only without bottle filler. Uses HFC-134A refrigerant Usa refrigerante HFC-134A Utilise du fluide frigorigéne HFC-134A 3 27 10 5 7 24 3 18 21 26 19 19 26 8 25 4B See Fig.
PAGE 3
2 9/16" 65mm F 5" 127mm 4 9/16" 116mm 7" 178mm Fig.
PAGE 4
VRCGRNTLDWS*C VRCGRNTL8WS*1C LVRCGRNTLDWS*C IMPORTANT ALL SERVICE TO BE PERFORMED BY AN AUTHORIZED SERVICE PERSON IMPORTANTE TODO EL SERVICIO DEBERÁ SER EFECTUADO POR UNA PERSONA DE SERVICIO AUTORIZADA HANGER BRACKETS & TRAP INSTALLATION INSTALACIÓN DE FIJADOR DE SUSPENSIÓN Y DEL PURGADOR 1) Remove hanger bracket fastened to back of cooler by removing one (1) screw. 2) Mount the hanger bracket and trap as shown in Figure 2. NOTE: Hanger Bracket MUST be supported securely.
PAGE 5
VRCGRNTLDWS*C VRCGRNTL8WS*1C LVRCGRNTLDWS*C LVRCGRNTL8WS*1C PUSH BUTTON MECHANISM MECANISMO DE BARRA DE EMPUJE MÉCANISME DU BOUTON-POUSSOIR 29 2 2 2 17 1 30 28 2 2 2 9 Fig. 5 20 24 20 25 4B 4A 20 26 24 7 Fig. 6 Fig. 7 Page 5 1000001742 (Rev.
PAGE 6
VRCGRNTLDWS*C VRCGRNTL8WS*1C LVRCGRNTLDWS*C 7/16” BOLT HOLES FOR FASTENING UNIT TO WALL TOP COVER LVRCGRNTL8WS*1C MOUNTING SCREWS 36 UNIT CENTER LINE Fig 8 Fig. 9 Fig. 10 Fig. 11 BRACKET & SCREWS Bottle Filler Installation Instructions 1) Remove two (2) mounting screws with 5/32” Allen wrench holding top cover to Bottle Filler (See Fig. 9). Remove top cover. Note do not discard mounting screws, they will be needed to reinstall top cover. 2) Remove wall mounting plate from Bottle Filler.
PAGE 7
VRCGRNTLDWS*C VRCGRNTL8WS*1C LVRCGRNTLDWS*C LVRCGRNTL8WS*1C BF11 - BF12 PROGRAM SETTING THE CONTROL BOARD VERIFY CONTROL BOARD SOFTWARE 1) To verify the software program of the control board the unit will need to be shut down and restarted. The chiller (if present) does not need to be shut down and restarted. 2) The units lower panel must be open to access the power cord and wall outlet. 3) Shut down the unit by unplugging the power cord from the wall outlet.
PAGE 8
VRCGRNTLDWS*C VRCGRNTL8WS*1C LVRCGRNTLDWS*C LVRCGRNTL8WS*1C OPERATION OF QUICK CONNECT FITTINGS BOTTLE FILLING UNIT SIMPLY PUSHIN IN SIMPLY PUSH TUBE TO TUBE TOATTACH ATTACH WALL MOUNTING PLATE A A TUBE TUBEIS IS SECURED SECURED INPOSITION POSITION IN B PUSH PUSHIN IN COLLET COLLET TORELEASE RELEASE TUBE TUBE TO C PUSHING TUBE IN BEFORE PUSHING TUBE IN BEFORE PULLING IT OUT HELPS TO PULLING IT OUTTUBE HELPS TO RELEASE RELEASE TUBE Fig.
PAGE 9
VRCGRNTLDWS*C VRCGRNTL8WS*1C OVERLOAD LVRCGRNTLDWS*C LVRCGRNTL8WS*1C 3 2 1 COLD CONTROL (WATER) COMPRESSOR C S RELAY M 6 5 3 2 BLK FAN 1 WHT GND Fig. 16 115V Wiring Diagram Diagrama de cableado de 115 voltios schéma de câblage de 115 volts FIVE PIN CONNECTOR FOUR PIN CONNECTOR MAIN BOARD PIGGY BACK TERMINAL ON POWER CORD WHITE I.R.
PAGE 10
VRCGRNTLDWS*C VRCGRNTL8WS*1C LVRCGRNTLDWS*C LVRCGRNTL8WS*1C PARTS LIST/ LISTA DE PIEZAS/ LISTE DES PIÈCES ITEM NO.