Installation Sheet

ManualsBrandsElkay ManualsPopular CollectionsElkay EZH20 36-1/8" Wall Mounted Bi-Level Station Hands Free Bottle Filler Combo - Cooler Operated and Vandal Resistant Bubbler

VRCGRNTLDWS*C VRCGRNTL8WS*1C LVRCGRNTLDWS*C LVRCGRNTL8WS*1C

1000001742 (Rev. C - 07/15)

Page 1

EZH2O Bottle Filling Station and Cooler

Manual de Instalación, Cuidado y Utilización

Manuel d’installation/entretien/utilisation

INSTALLATION, CARE & USE MANUAL

Station de remplissage de bouteille EZH2O et refroidisseur

Estación de llenado de botella EZH2O y enfriador

Summary of content (9 pages)

PAGE 1
VRCGRNTLDWS*C VRCGRNTL8WS*1C LVRCGRNTLDWS*C LVRCGRNTL8WS*1C INSTALLATION, CARE & USE MANUAL Manual de Instalación, Cuidado y Utilización Manuel d’installation/entretien/utilisation EZH2O Bottle Filling Station and Cooler Estación de llenado de botella EZH2O y enfriador Station de remplissage de bouteille EZH2O et refroidisseur Page 1 1000001742 (Rev.
PAGE 2
VRCGRNTLDWS*C VRCGRNTL8WS*1C LVRCGRNTLDWS*C LVRCGRNTL8WS*1C Note: Danger! Electric shock hazard. Disconnect power before servicing unit. Nota: peligro! Peligro de descarga eléctrica. Desconecte antes de reparar la unidad. Remarque : Danger ! Risque d'électrocution. Débrancher avant de réparer l'appareil. Pictured is unit only without bottle filler. Uses HFC-134A refrigerant Usa refrigerante HFC-134A Utilise du fluide frigorigéne HFC-134A 3 10 5 7 3 27 24 18 21 26 19 19 26 8 25 See Fig.
PAGE 3
Page 3 5" 127mm 10" 254mm 2 7/16" 63mm 11/16" 18mm B * STANDARD TWO-LEVEL INSTALLATION Fig. 2 6 1/4" 159mm CL 3 1/2" 89mm 4 1/2" 114mm E 25 1/8" 638mm 20 1/8" 511mm 18 3/4" 476mm F A D 13 7/8" 352mm 5 3/4" 146mm 27" 686mm ADA REQUIREMENT 31 15/16" 811mm RIM HEIGHT 32 15/16" 837mm ORIFICE HEIGHT 39 7/16" 1002mm ORIFICE HEIGHT 2 5/8" 67mm C 12 5/16" 313mm 4 1/8" 105mm 8" 203mm HANGER BRACKET 18 5/8" 472mm 3 9/16" 90mm *ADA REQUIREMENT *REQUISITO DE A.D.A.
PAGE 4
VRCGRNTLDWS*C VRCGRNTL8WS*1C LVRCGRNTLDWS*C IMPORTANT ALL SERVICE TO BE PERFORMED BY AN AUTHORIZED SERVICE PERSON IMPORTANTE TODO EL SERVICIO DEBERÁ SER EFECTUADO POR UNA PERSONA DE SERVICIO AUTORIZADA HANGER BRACKETS & TRAP INSTALLATION INSTALACIÓN DE FIJADOR DE SUSPENSIÓN Y DEL PURGADOR 1) Remove hanger bracket fastened to back of cooler by removing one (1) screw. 2) Mount the hanger bracket and trap as shown in Figure 2. NOTE: Hanger Bracket MUST be supported securely.
PAGE 5
VRCGRNTLDWS*C VRCGRNTL8WS*1C LVRCGRNTLDWS*C LVRCGRNTL8WS*1C PUSH BUTTON MECHANISM MECANISMO DE BARRA DE EMPUJE MÉCANISME DU BOUTON-POUSSOIR 31 17 15 13 17 1 32 30 14 2 16 9 Fig. 5 20 20 24 4A 4B 26 25 24 Fig. 6 Fig. 7 Page 5 1000001742 (Rev.
PAGE 6
VRCGRNTLDWS*C VRCGRNTL8WS*1C 7/16” BOLT HOLES FOR FASTENING UNIT TO WALL LVRCGRNTLDWS*C LVRCGRNTL8WS*1C MOUNTING SCREWS TOP COVER 41 UNIT CENTER LINE Fig. 9 Fig 8 Fig. 11 Fig. 10 BRACKET, WASHERS, & SCREWS Bottle Filler Installation Instructions 1) Remove two (2) mounting screws with 5/32” Allen wrench holding top cover to Bottle Filler (See Fig. 9). Remove top cover. Note do not discard mounting screws, they will be needed to reinstall top cover.
PAGE 7
VRCGRNTLDWS*C VRCGRNTL8WS*1C LVRCGRNTLDWS*C LVRCGRNTL8WS*1C BF11 PROGRAM SETTING THE CONTROL BOARD VERIFY CONTROL BOARD SOFTWARE 1) To verify the software program of the control board the unit will need to be shut down and restarted. The chiller (if present) does not need to be shut down and restarted. 2) The units lower panel must be open to access the power cord and wall outlet. 3) Shut down the unit by unplugging the power cord from the wall outlet.
PAGE 8
VRCGRNTLDWS*C VRCGRNTL8WS*1C LVRCGRNTLDWS*C LVRCGRNTL8WS*1C WALL MOUNTING PLATE BOTTLE FILLING UNIT OVERLOAD 3 2 1 COLD CONTROL (WATER) COMPRESSOR C S RELAY M 6 5 3 2 BLK FAN 1 WHT GND Fig. 13 115V Wiring Diagram Diagrama de Cableado de 115 Voltios Schéma de Câblage de 115 Volts Fig.
PAGE 9
VRCGRNTLDWS*C VRCGRNTL8WS*1C LVRCGRNTLDWS*C LVRCGRNTL8WS*1C PARTS LIST/ LISTA DE PIEZAS/ LISTE DES PIÈCES ITEM NO.