Datasheet

ManualsBrandsElma ManualsRotary SwitchesRotary Switch, 1 Poles, 10 Positions, 36°, PCB Mount

1 mm = 0.04 inch 1 inch = 25.4 mm

Rotary Switches Type 01

ø4

0,8

ø2

ø18

7,5

39,2 18

M8 x 0,75

22,3

SW10

40,3

39,2

M8 x 0,75

ø4

0,8

20,2

18,2

SW10

8,2

2,2

7,5

Description

Rotary switch with bridge contact principle

Overall diameter

18 mm

Central mounting

Threaded bushing

M16 x 0,75 with 3 mm diameter shaft

M18 x 0,75 with 4 mm diameter shaft

M10 x 0,75 with 6 mm diameter shaft

Indexing angle

30° = 12 switching positions

36° = 10 switching positions

60° = 16 switching positions

On switches with fixed end-stop,

adjustable stops can be set, by means

of a plastic pin, on any position

between 2 and the maximum (to be

ordered separately).

Number of poles per wafer

1, 2 or 4 (poles)

Switching mode

Shorting or non-shorting

Contact material

Silver and Gold plated 3 µm

Terminals

Solder lug or PCB mountable

Front-panel cut out

~14,5 3,5

7,5

16,7

ø1,5

ø1,3

1x12 / 1x12 u

Verdreh-

schutz

Ansicht des Bohr-

planes von der

Schalterachse her

1x10 m. A. 1x10 o. A.

Verdrehschutz

1x11 / 1x11 u 2x6 / 2x6 u 4x3 / 4x3 u

1x6 u 4x2 u

2x3 u

Drilling diagram for

indexing angle 30°

With solder tags for cables

With pins for printed circuits

Drilling diagram for

indexing angle 60°

Drilling diagram for

indexing angle 36°

SW = Key spanner

Locating

lug

Drilling diagram

view from the

spindle end

Locating

lug

Summary of content (6 pages)

PAGE 1
Rotary Switches Type 01 2 2,2 ø2 1 SW 10 ø4 7,5 SW = Key spanner Front-panel cut out 7,5 M8 x 0,75 With solder tags for cables 8,2 ø18 0,8 6 SW 10 2 18 1 ø4 18,2 M8 x 0,75 39,2 8,2 0,8 20,2 6 22,3 40,3 39,2 With pins for printed circuits Drilling diagram for indexing angle 36° Drilling diagram for indexing angle 30° 3,5 Drillingdes diagram Ansicht Bohrview from planes von the der spindle end her Schalterachse 1x12 / 1x12 u 30° Locating Verdrehlug schutz 3,5° 12 1 2 4 A 5
PAGE 2
Rotary Switches Type 01 Technical Data Mechanical data Material Electrical data Mechanism indexing Mechanism: plastic with metal threaded bush Shaft: stainless steel Application data 30° = 12 positions shorting or non-shorting 36° = 10 positions shorting 60° = 6 positions non-shorting Insulation material Switching capacity with resistive load: Wafers: HF-ceramic Rotor: polybutylene (PBTB) Switching torque with 1 wafer, 1 pole Contact material Rivet (copper) and segment (brass) Standard: 4 Ncm (~
PAGE 3
Special Options to Rotary Switches Type 01 Ordering an option To order a special option please use the order form. Please specify your requirements and fax it to your local contact or to Elma. Special shaft lenght To order, state the shaft lenght AL as shown in diagram, measured from mounting face. Please specify shaft length on the order form. Special types of shaft Locating lug e. g. 60 ° Angle in ° from locating lug. Switch on position 1 e. g. 30 ° e. g.
PAGE 4
Special Options to Rotary Switches Type 01 Switches with 2 drive shafts It is possible for two switches to be operated individually by concentric shafts on the same mounting. When ordering, the type number of each switch should be given and specified on order form. Special shaft diameters Type 01 switches are also available with the following shaft diameters: Aø D SW L AL Standard AL max.
PAGE 5
Order form for Special Options to Rotary Switches Type 01 □ Quote Copy – Fill in – Fax Company request □ Order Customer No. Address Phone Name Fax e-mail Quantity Requested delivery date Similar to order No. Function = Pol 1□ Number of wafers 2□ x Special stop from Pos. Pos. to Pos. With solder tags for cables □ Contact material With pins for printed circuits □ Switching torque (1 wafer/1 pole) Standard 4 Ncm □ spec. 2 Ncm □ silver (Ag) □ gold /Au 3 µm) □ spec.
PAGE 6
Ordering Code to Rotary Switches Type 01 Options This code specifies the function of the switch 0 1 – X X X X – X X X X X X X X Switch Type 0 = shaft 4 mm Standard M = shaft 3 mm N = shaft 6 mm Number of wafers 00 = Standard Number of poles 11 = BG 11 Pos. 10 = BG 10 Pos. 09 = BG 9 Pos. Free character 08 = BG 8 Pos. 07 = BG 7 Pos. 06 = BG 6 Pos. 0 = Ag shorting 05 = BG 5 Pos. 1 = Ag non-shorting 04 = BG 4 Pos. 3 = Au 3 µm shorting 03 = BG 3 Pos. 4 = Au 3 µm non-shorting 02 = BG 2 Pos.