VISUAL PRESENTER OX-1 INSTRUCTION MANUAL
IMPORTANT SAFEGUARDS ■ Read Instructions All the safety and operating instructions should be read before the appliance is operated. ■ Retain Instructions The safety and operating instructions should be retained for future reference. ■ Heed Warnings All warnings on the product and in the operating instructions should be adhered to. ■ Follow Instructions All operating and use instructions should be followed. ■ Cleaning Unplug this product from the wall outlet before cleaning.
• If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation. • If the product has been dropped or damaged in any way. • When the product exhibits a distinct change in performance -this indicates a need for service.
WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. The connection of a non-shielded equipment interface cable to this equipment will invalidate the FCC Certification or Declaration of this device and may cause interference levels which exceed the limits established by the FCC for this equipment. It is the responsibility of the user to obtain and use a shielded equipment interface cable with this device.
USAGE PRECAUTIONS ■ Be sure to use the supplied USB cable. ■ The supplied USB cable is designed for exclusive use with this product. Do not use it with other products. ■ Be careful not to pinch your finger when you move the arm. ■ When storing the product, do not leave it under direct sunlight or by heaters. It may be discolored, deformed, or damaged. ■ Do not place the product in any humid, dusty, salt bearing wind, or vibrating locations.
HANDLING PRECAUTIONS The followings are special precautions against mishandling of the product. Pay close attention to them. ①Installation Do not place the product on an unstable place. ②Setting up When setting up the product, hold the body around the operating panel. Be careful not to pinch your fingers. ③Carrying the product Carry the product by folding the arm so as not to damage the camera. Do not carry by holding the arm or camera head.
■ TABLE OF CONTENTS IMPORTANT SAFEGUARDS ·········································································· 2 USAGE PRECAUTIONS 5 HANDLING PRECAUTIONS 6 ■ TABLE OF CONTENTS ············································································· 7 ➊ PREPARATION ······················································································· 8 ◆PACKAGE CONTENTS 8 ➋ BASIC OPERATIONS ··············································································· 9 ◆THE NAME OF EACH PA
➊ PREPARATION ◆PACKAGE CONTENTS The items below are included with this product. If any item is missing, contact the dealer from whom you purchased this product. USB2.0 cable OX-1 Quick Start Guide Warranty Card (For Japan/ North America only） IMPORTANT SAFEGUARDS Note About the Desk Clamp (sold separately) You can secure the product to a desk with the Desk Clamp. (⇒P.14) CAUTION ・Do not wrap the USB2.0 cable tightly around the product.
➋ BASIC OPERATIONS ◆THE NAME OF EACH PART ② ⑧ ① ⑨ ⑦ ④ ③ ⑤ Name ① AF button ② LED lighting button ③ Adjustment screw ④ USB port ⑤ LED lighting ⑥ Camera lens ⑦ Camera head ⑧ Arm ⑨ Mic 9 ⑥
■OPERATING BUTTONS ② ① Name ① ② AF button LED lighting button Description To focus automatically. (⇒P.14) To on or off the LED lighting. (⇒P.14) ◆RESOLUTION／FRAME RATE The following table shows the output resolution and frame rate.
➌ PREPARATION AND CONNECTION ◆SETTING UP STEP1 STEP2 STEP3 STEP4 Raise the camera head as indicated by an arrow while holding the base. Raise the upper arm as indicated by an arrow. Set the camera head horizontally. Rotate the camera head to adjust the shooting angle. STEP4 STEP3 Camera head Arm (upper) STEP1 Base STEP2 120° 180° Arm (lower) Adjustment screw Camera CAUTION ・Be careful not to pinch your fingers when moving the arm. ・Do not hold the arm or camera head when carrying the product.
◆CONNECTING TO A COMPUTER The product is compliant to UVC (USB video class) standard. You can transfer the image via USB by connecting the product to a computer using the USB cable. Type A USB cable ⇒To the USB port USB cable ⇒To type B port 1．Connect the type B connector of the supplied USB2.0 cable to [ ] connector in the side of the product. 2．Connect the type A connector of the USB2.0 cable to the USB port of your running computer. 3．Launch the viewer on the connected computer.
◆TURNING ON OR OFF THE POWER Power ON After connecting the product to a computer with the USB2.0 cable, launch the viewer software and select the product. The product will turn on and the image will be displayed. Power OFF Turn off the product from the viewer software. Then remove the USB2.0 cable. ◆USING IMAGE MATE +C You can transfer the image of the product to a computer by using “Image Mate +C”. “Image Mate +C” runs on the web browser, so you don’t have to install it.
➍ USING THE PRODUCT ◆ADJUSTING THE FOCUS Press the AF button to automatically focus on the subject. ◆TURNING THE LED LIGHTING ON/OFF Press the LED lighting button to turn on the LED lighting. Press this button again to turn off the LED lighting. CAUTION • To take shots of people, turn off the LED lighting. • Make sure that the light from the LED lighting does not shine directly into your eyes. • This product is equipped with a high-brightness LED. You can safely use it to light up the object.
➎ TROUBLE SHOOTING ◆SYMPTOMS AND CONFIRMATION Check the following items. If any abnormality is found, consult the dealer from whom you purchased this product or our nearest branch/office. Symptom Cannot turn on the product. Possible cause / remedy ・The power of the connected computer is not turned on. ・Sometimes the product does not show any indication of power on. Start the viewer software on the connected computer and check if the image is displayed. ・Reconnect the USB2.
A software error ・If it is taking too much time for the preparation of the image output, the message appears and software may determine this to be an error. Restart the product, reconnect it to the computer, and then start the software. the image is not displayed. The image sometimes ・The displayed image may pause for a brief second when the object freezes. moves quickly. In that case, adjusting the brightness manually may improve the problem. There is a distortion of ・Use a high-spec computer.
➏ SPECIFICATION ◆MAIN CAMERA Item Specifications Power source DC5V Power consumption 2.5W Outside dimensions W：317mm D：108mm H：375mm(When setup) W：337mm D：108mm H：54mm(When folded) Weight Approx. 630g（Main body only） USB device USB2.0 TypeB × 1 Power supply：bus power Lens F=2.0 Frame rate 30fps（max） Focus working range From lens surface：100mm 〜 ∞ Focus Auto（One-push） Exposure Auto Image pick-up element 1/3.
Exposure Auto/manual（Manual：Set value -8〜1） Default setting：Auto - - ✔ ✔ Focus Auto/manual Default setting: Manual - - ✔ ✔ Low-light ON/OFF ✔ compensation Default setting: OFF ※1 To obtain high-resolution image output, select the resolution (ex.1920x1080) with 15fps. Some electronic whiteboards do not support 15fps. In that case, select the default resolution of 1280x720. ※ Depending on the software viewer to use, some function cannot be configured.
■ TRADEMARKS AND LICENSES and Image Mate are registered trademarks of ELMO Co., Ltd. HDMI and High-Definition Multimedia interface are trademarks or registered trademarks of HDMI Licensing LLC. Windows, or names of other Microsoft products are trademarks or registered trademarks of Microsoft Corporation in the United States and other countries. Google, Google Chrome and Android are registered trademarks of Google Inc. Mac OS is a registered trademark of Apple Inc. in the United States and other countries.
株式会社エルモ社 OVERSEAS SUBSIDIARY COMPANIES 〒457-0078 名古屋市南区塩屋町⼀丁⽬３番地４ Web：https://www.elmo.co.jp 製品のお問い合わせは、下記営業所へ □ 東⽇本営業所 □札幌オフィス 〒001-0021 札幌市北区北 21 条⻄ 8 丁⽬ 3 番 8 号 バックスビル TEL. 011-738-5811 □仙台オフィス 〒980-0802 仙台市⻘葉区⼆⽇町 13 番 18 号 ｽﾃｰｼｮﾝﾌﾟﾗｻﾞﾋﾞﾙ 6 階 TEL.022-266-3255 □ ⾸都圏営業所 〒108-0073 東京都港区三⽥ 3 丁⽬ 12 番 16 号 ⼭光ビル 4 階 TEL.03-3453-6471 □ 中⽇本部営業所 ELMO USA CORP. □Headquarters 6851 Jericho Turnpike Suite 145 Syosset, NY 11791 Tel. (516) 501-1400 Fax.(516) 501-0429 E-mail： elmo@elmousa.com Web：https://www.
