6mm CHANNEL LOAD/Ne ~O[JfD ·.PBOJECTOB IG-Cl/IG-CL .
IMPORTANT SAFEGUARDS W hen using your photographic equipment, basic safety precautions should always be followed, including the following: 1. Read and understand all instructions. 2. Close supervision is necessary when any appliance is used by or near children. ' Do not leave appliance unattended while in use. "- 3. Care must be taken as burns can occur from touching hot parts. 4.
Congratulations and thank you on joining the large nation-wide family of ELMO 16-CL sound projector owners. You have selected a precision-engineered projector that will give you the quality picture and sound reproduction you expected from ELMO. However, to enjoy your ELMO projector be sure to read this entire manual for important, helpful information. CONTENTS Major parts descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 2 Preparation for projection ...........................
Major parts descriptions Reel lock ------~ Take-up reel arm - - - - - - - - . . . . . : Folding button for take-up reel a r m - - - - - - - - - - - - - - i Front cover---------~ Tension roller ------------i Tone control k n o b - - - - - - - - - Volume control k n o b - - - - - - - - - M-O switch (Note: This switch not applicab l e to model 16-CL - optica l on ly .) 80o-ft.
~~!!!~----- Reel lock '1-- - - - - - Feed reel arm :- - - - - - - - - Folding button for feed reel arm ,.-------Slot-in roller - - - - - - Threading guide No. 1 - - - - - - Framing knob ------Scope lens holder socket f - - - - - - - Focusing knob - - - - - - Speaker - - - - - - Projection lens cover , -_ _ _ _ Threading guide No.2 f------- Master motor, lamp, forward & rewind control switch : : - - - - - - - Projector elevation control knob ! 1!.Q!i!--------Main power fuse ,.
Preparation for projection o Set up your projector and screen properly. For steady projection, place the projector on a sturdy support at right angle to the screen. Making sure the master control power switch is at OFF, connect the built-in power cord, which is stored in the top side receptacle of the projector, to the AC electrical outlet. Pull up the feed reel arm and take-up reel arm to maximum stop position.
Install the take-up reel 240m (800ft.), which is stored on the rear of the projector, on the rear reel spindle. The reel capacity of the projector is max. 600m (2,OOOft.). Also install the feed reel on the front reel spindle. At this time, be sure to set the reel in correct position by turning down the reel locks. Set the M-O switch in accordance with the film to be projected. Set it to M position for magnetic sound film and 0 position for optical sound film, respectively.
Film threading O Hold the tip of the film leader between thumb and index finger then pull the leader first through the slot-in roller, next over the No.1 and No.2 rollers and finally over the tension roller. Slot-in roller 6 Threading guide No.1 Threading guide No.
After the film threading is completed, wind the leader on the take-up reel. Make sure the fi 1m is properly threaded through the channel by turning the take-up reel clockwise with hand.
o Projection Turn the master control switch clockwise to ffJ ,then turn it further to (]~ , and the lamp is switched on and simultaneously the projector starts forward. Adjust focusing by turning the focusing knob. If a frame I ine appears on the screen, adjust the framing knob to left or Framing knob right. Adjust the sound volume by turning the outer volume control knob clockwise.
Various, projections .Quick review This feature is used to see specific frames you wish to review. Turn the control switch counter clock-wise from a~ all the way to ~ and the film is quickly rewound through the gate. Then turn the control switch to OFF, as soon as you get the desired frame for re-projection. After making sure the film has stopped, turn the control switch from OFF all the way to a~ through 1> .
• When using extension speaker I n the event you have occassion to use an accessory extension speaker for a large audience in a large auditorium, connect the speaker jack to the receptacle at the rear of the projector. This procedure will automatically shut off the built-in speaker circuit. Extension speaker jack Note: Use optional adapter cord SC-004 for connecting Elmo extra speaker to your projector.
• Public address system You can utilize your ELMO sound projector as a public address system during projection when an accessory microphone is inserted into the microphone jack at the rear left side of the projector. Use the micro- phone with an impedance of 500 ~ 10k. Public address through a microphone during projection supercedes the sound from the projected film. Microphone jack • HIGH-LOW lamp switch The switch is originally set to High position.
Rewinding • When the projection is completed, rewind the film as follows. o I nsert the film end into the slot of the front reel hub. @ Turn the operation switch to ~. In this case the projector may start rewinding only after a few seconds' pause depending on the length of film on the reel to b e reo wound . The projector is d esigned to increase motor 8 torque gradually for the protection of fi I m. After the film is rewound, turn the operation switch to OFF .
Maintenance Clean the film channel and lens prior to projection; accumulation of dust and film particles in the film channel gate will scratct"l the film and decrease the projected image quality . • How to remove and install covers • Projection lens cover To remove, hold the cover as shown in the picture and pull it out toward yourself. To install, align the guides at the lower side and push the upper part of t he cover into place as shown in the picture.
To install the cover, align the framing knob with the cover notch and the guide pins at the upper left and lower right with the corresponding holes and push the cover into position. (Cover shown in reverse) Cover notch Guide pin hole • Cleaning film gate Be sure to remove the film from the channel when cleaning the film gate. Remove the projection lens cover. Hold the pressure plate as shown in the picture and pull it out toward yourself, and the pressure plate can be removed.
Use the stiff cleaning brush (supplied) to clean film channel gate, then wipe clean with lint-free cloth. After the cleaning is over, align the two pins at the upper and lower parts of the pressure plate holder with the corresponding slots on the pressure plate base and push it back to place. • Cleaning rollers, solar battery and sound lens Brush off the rollers, solar battery and sound lens with the clean soft brush supplied.
• Cleaning projection lens To remove the projection lens, pull it out straight while pulling the focusing knob toward yourself. To remove the dust, wipe the lens surface gently with soft, clean, lint-free cloth. Groove To put the lens back, push it all the way to position while pulling the focusing knob toward yourself, and pull it until a click is heard . This click sound means that the pin at the end of the focusing knob is positively inserted into the groove of the lens holder.
Replacing lamp and fuse BE SURE TO DISCONNECT THE POWER CORD WHEN REPLACING LAMP AND FUSE . • Replacing projection lamp The type of projection lamp to be replaced is JCR24V-250W or ANSI ELC or Osram 64653. Remove the front cover. Remove the lamp cover by loosening the screws cou nterclockwise. Eject the blown lamp by pushing down the ejector lever to the left. It is advisable to keep a spare projection lamp handy for immediate replacement, should an unexpected break or burn-out develop during projection.
To replace a new lamp, push it into the socket as shown in the picture. At this time, be sure to insert the lamp firmly into its socket. optimum If it is inserted halfway into the socket, the projection performance can't be ·achieved or the socket may be burned out. Holder _---li'- Socket • Replacing exciter lamp The type of exciter lamp to be replaced is KE-04 or ANSI B R K. o Remove the blown exciter lamp by turning its head counterclockwise.
• Replacing fuse To remove the fuse holders, turn the holder heads counterclockwise with a Philips head screwdriver. Exciter lamp fuse Amplifier fuse Power fuse IMPORTANT Use the fuse with specified value for each of the three as indicated above. • Check the exciter lamp fuse for blow·out when no sound is reproduced when projecting optcial sound film. At this time, be sure also to check the exciter lamp filament for blow-out.
Trouble-shooting hints When the motor fails to operate: • Check the power cord for proper connection. • Check the power (main) fuse for blow-out. When the lamp is not lit on: • Check the lamp filament for blow-out. • Check the lamp for proper connection with its socket. When no sound is reproduced: • Check the M-O switch for the correct position corresponding to the film type used. (Not applicable to 16-CL optical) • Check the exciter lamp if lighted (only in case of optical sound film) .
When changing the projection speed from 24 fps to 18 fps or to change electric current cycles (50Hz - 60Hz) • The projector is originally fixed for 24 fps. operation. To change to 18 fps., remove the rear cover by loosening four screws and change the projection speed as shwon in the picture . • Electric current cycles are adjusted at the factory for specific destined countries.
Accessories This lens is used for projecting Cinemascope movies. It can be installed in front of the projection lens simply by mounting it on the accessory socket of the projector. The projected image is horizontally magnified twice . • Zoom lens F1.7 f= SO ~ 100mm This wide range zoom lens eliminates the neccessity of moving projector to or from screen for desired size of picture . • Telephoto projection lens F1.B f= 7Smm This telephoto lens is for projection in a large auditorium .
• Wide-angle projection lens F1.4 20mm This wide -angle lens is designed for projection in a small room. This attachment lens converts the • Conversion lens focal length of the projection lens to either xO.8 or x1.25, i.e., the ! standard 50mm lens plus this accessory serves as a 40mm wideangle lens or by reversing it a 63mm tele photo lens. You can make use of it when the projected image is too small or large.
• Twin extension speakers ES-1000 High performance extension speakers with a 10" (25 cm) woofer and a tweeter. Stores conveniently in one portable case. Rated input: 10W (Max. 15W) 16 ohms • Carrying case with speakers The carrying case incorporates 2 x 16.5 cm diameter dynamic speakers and is especially useful for projection in a large auditorium.
Specifications E xciter lamp Amplifier MUsiqJoWer OllltPlilt TOfle eOfltrol Pubilfu address system Speeifieatiofls afld desigfls are slIIbject to chaflge witholilt prior f1otice.
EIf1.9 ELMO CO.,LTD. 6, Kamiho-dori 1-chome, Mizuho-ku, Nagoya, 467, JAPAN Tel. 052-811-5131 Fax. 052-811-5142 OVERSEAS SUBSIDIARY COMPANIES U.S.A. Elmo Mfg. Corp. 70 New Hyde Park Road, New Hyde Park, NY 11040-9980 Tel. 516-775-3200 Fax. 516-775-3297 21720 Nordhoff Street, Chatsworth, CA 91311-5826 Tel. 818-346-4500 Fax. 818-998-4186 Canada Elmo Canada Mfg. Corp. 44 West Drive, Brampton, Ontario, L6T 3T6 Tel. 416-453-7880 Fax. 416-453-2391 West Germany Elmo (Europe) G.m.b.H. Karl-Rudolf-Str.