Quick Start Guide

Wireless Pen Tablet
6X1xxxx01 R0-Xxx
□ Pen
□ Tablet
（CRA-2）
（This book ）
□ Quick Start
Guide
CRA-2 Quick Start Guide
● PACKAGE CONTENTS
● USING THE PRODUCT
● DETAILED USAGE OF THE PRODUCT
● PREPARATION
□ Pen holder
□ Wireless
Dongle
□ Extra core x 8
(※Extra cores are
in the pen holder.)
□ USB cable
(For charging or
for connecting to
a device)
● Charging
●接続端子・スイッチを確認する
Side view (left)
Use the supplied wireless dongle to connect the tablet to a device wirelessly.
※ You can also use the tablet by connecting it to a device using the supplied USB cable.
※ Available functions
may dier depending
on the document
camera used.
The tablet will start to
recognize the pen if the
working range is touched
by the pen tip button.
The tablet will enter sleep
mode after about 45
minutes of inactivity.
※ Only when connected
wirelessly
When the pen tip becomes round, replace it with the supplied "extra
core". Use the supplied pen holder when replacing the pen tip.
The Status LED will turn green and go o
after the power is on.
● When connecting wirelessly
⇒The tablet will power on when the
wireless switch is set to on.
● When connecting with the USB cable
⇒ The tablet will power on when it is
connected to a running computer or
document camera.
1. Turn on the power.
2. Operate the tablet
● Replacing the pen tip
● Pen operations
● Storage for the pen and wireless dongle
● Shortcut keys
● Connecting to a device
※ Caution
・When replacing the pen tip, be sure to replace it with the supplied "extra core".
・Make sure that children do not put small parts into their mouths.
Step1.Rotate the pen holder counterclockwise
(arrow ① ) and remove the cover (arrow ② ).
Step2.Put the pen to the center of the pen holder.
Tilt the pen to remove the pen tip.
Step3.Insert the extra core rmly into the pen until
it stops.
Wireless switch
Storage for the wireless dongle
Slide and push the dongle into
the storage.Push the dongle
with your nger to take it out.
Pen storage
※ You need to install the EIT on your computer
to use the tablet with your computer. Available
functions may dier depending on the document
camera used.
※ The wireless switch will be
used only when the tablet
is connected wirelessly.
ON（Enabled）
By connecting the wireless dongle to a computer
or document camera, you can use the CRA-2
wirelessly.
OFF（Disabled）
The power enters standby mode.
※ You can use the tablet no matter the wireless
switch is on or o when connecting with the
USB cable.
USB port
Storage for the pen
Insert the pen from the pen tip
into the storage.
Pull the pen with your nger to
take it out.
Storage for
the wireless
dongle
Status LED
Charging: Red
Fully charged: O
①
⑤
②
③
④
Connecting to a computer
You can control your computer like a
mouse. By using with the EIT, you can
add annotations to the screen image.
Insert the wireless
dongle to the USB
port of the computer.
Name Description
①
Document
camera mode
To display the document camera image.
②
Whiteboard
mode
To display the whiteboard screen.
③
Playback
mode
To display images stored.
④
Operation/
Settings mode
・When connecting to a computer:
to control a computer as a mouse
・When connecting to the document
camera: to congure pen settings
⑤
Close/ Hide
・When connecting to a computer:
to close the EIT
・When connecting to the document
camera: to display or hide menus
Status
LED
①
②
＜ Step1 ＞
Pen holder
Cover
＜ Step2 ＞ ＜ Step3 ＞
Right click
(when using with the document camera
: eraser)
When using with the
document camera
: eraser
Left click
Connecting to the document camera
You can add annotations to the document
camera image or control the document camera.
Insert the wireless dongle to
the USB port of the document
camera.
Working area
Connect the tablet to a computer with
the supplied USB cable.
□ IMPORTANT
SAFEGUARDS
● Checking the connection ports and
switches
For detailed information about the Instruction Manual, refer to the following website:
https://www.elmousa.com/
https://www.elmoeurope.com/index.php/en/