Solo Whistle Digital Servo Drive Cable Kit CBL-MLXAI CBL-MLXAUX CBL-MLXFDBK CBL-SOLKIT-001 December 2008 (Ver. 1.0) www.elmomc.
Important Notice This guide is delivered subject to the following conditions and restrictions: This guide contains proprietary information belonging to Elmo Motion Control Ltd. Such information is supplied solely for the purpose of assisting users of the Solo Whistle servo drive in assembling the required cables for their drive. The text and graphics included in this manual are for the purpose of illustration and reference only.
Solo Whistle Cable Kit i MAN-CBLKIT-SOLWHI (Ver 1.0) Contents 1. Introduction ................................................................................................................... 1-1 1.1 Solo Whistle Connectors ........................................................................................................................ 1-1 1.2 Cable Cross Reference ............................................................................................................................ 1-2 1.
Solo Whistle Cable Kit 1-1 MAN-CBLKIT-SOLWHI (Ver 1.0) 1. Introduction This document provides the wiring details for the cables used to connect the Elmo Solo-Whistle digital servo drive with the end-user application. The servo drive-side pinouts are provided in Chapter 3 of the drive’s installation guide. The cables come in one length: 2 meters (6 ½ feet). 1.1 Solo Whistle Connectors The table below presents the connector panel of the Solo Whistle drive and specifies the cable connectors.
Solo Whistle Cable Kit Introduction MAN-CBLKIT-SOLWHI (Ver 1.0) 1-2 1.2 Cable Cross Reference 1.2.1 Solo Whistle Cable Application Cable Part. No.
Solo Whistle Cable Kit 2-1 MAN-CBLKIT-SOLWHI (Ver 1.0) 2. Cable Kit The Solo Whistle Cable Kit (CBL-SOLKIT-001) is available for purchase directly from Elmo Motion Control. The cable kit includes the six cables listed in Table 2-1. All the cables are 2 m long.
Solo Whistle Cable Kit 3-1 MAN-CBLKIT-SOLWHI (Ver 1.0) 3. Main Feedback Cable (CBL-MLXFDBK) The main feedback cable is made from 24-AWG, six twisted-pair shielded cable. There is one type of feedback cable, which uses a 12-pin Molex 2 mm pitch plug on the SimplIQ side. The Main Feedback Cable (CBL-MLXFDBK) is open on the motor side so that it can be connected to customer-specific connectors. Pin No.
Solo Whistle Cable Kit 4-1 MAN-CBLKIT-SOLWHI (Ver 1.0) 4. Auxiliary Feedback Cable (CBL-MLXAUX) The auxiliary feedback cable is a 24-AWG twisted-pair shielded cable. It is connected using an 8-pin Molex 2 mm pitch plug.
Solo Whistle Cable Kit 5-1 MAN-CBLKIT-SOLWHI (Ver 1.0) 5. Communication Cables The communication cables use 26-AWG two twisted pair shielded cable. They are connected using a 3-pin Molex 2 mm pitch plug. Elmo drives can communicate using the following options: RS-232, full duplex CAN open (CAN in & CAN out) The Communication Cables (CBL-MLXAI) are open on the motor side so that it can be connected to customer-specific connectors. 5.1 RS232 Communication Cable (CBL-MLXAI) Pin No.
Solo Whistle Cable Kit 6-1 MAN-CBLKIT-SOLWHI (Ver 1.0) 6. I/O Cable (CBL-MLXFDBK) The I/O cable is made from 24-AWG, six twisted-pair shielded cable. There is one type of I/O cable, which uses a 12-pin Molex 2.0 mm pitch plug on the SimplIQ side. The I/O Cable (CBL-MLXFDBK) is open on the motor side so that it can be connected to customer-specific connectors. Pin No.