USER MANUAL Elo Touch Solutions Touch All in one computer i-series 2.
Copyright © 2017 Elo Touch Solutions, Inc. All Rights Reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, including, but not limited to, electronic, magnetic, optical, chemical, manual, or otherwise without prior written permission of Elo Touch Solutions, Inc. Disclaimer The information in this document is subject to change without notice.
Table of Contents Section 1: Introduction ...................................................................................................................................................................................................................... 4 Section 2: Unpacking and Operation .................................................................................................................................................................................................
Section 1: Introduction Product Description Your new i-Series 2.0 Interactive Signage system combines the reliable Elo Touch Solutions performance with the latest developments in touchscreen technology and display design. This combination of features creates a natural flow of information between a user and the i-Series 2.0 system. This i-Series 2.0 system incorporates an active matrix thin-film-transistor and LCD panel to provide superior display performance.
Section 2: Unpacking and Operation Box Contents Verify that the box contains: • I-series 2.0 system • Quick Install Guide • Power brick • North American Power Cable • Europe Power Cable • Two (2) cable strain reliefs • Two (2) screws The connectors are accessed by removing the cable security covers from the rear of the i-Series 2.0 system. User Manual – i-series 2.
Elo i-series 2.0 Layout User Manual – i-series 2.
For units with Power over Ethernet Support User Manual – i-series 2.
i-series 2.0 EloView Engine The Eloview engine can be mounted to various Elo monitors using the VESA pattern or with optional monitor brackets. User Manual – i-series 2.0 UM600106 Rev.
Power Press the power button to turn the Elo i-series 2.0 on. Press and hold power button when the system is on to bring up the Shut Down option popup. In the event that the system freezes and does not respond, press and hold the power button until the system turns off. If the system does not turn off via the power button, the system will need to be powered down by unplugging the power cord from the wall. The Elo I-series 2.
Operating System System comes with Android 7.0.1 pre-loaded. Touch Technology The i-series 2.0 uses Projected Capacitance touch screens, 10 simultaneous touches can be reported at one time. Gesturing Images For multi-touch monitors, the following gestures are possible: Dual Touch Gestures and their Functions: Swipe – The action of moving a finger across the screen.
Video An LCD panels native resolution is its width and height measured in number of pixels. In almost all cases, an image displayed on an LCD monitor will look best when your image resolution matches the LCD panels native resolution. 10.1” is 1280x800, 15.6”/21.5”/Eloview engine operate at 1920x1080. Audio Earphone out and Audio In are supported over the USB port using a dongle.
Wi-Fi + Bluetooth The following protocols are supported for Wi-Fi and Bluetooth: Bluetooth 4.1+ BLE, A2DP/ HID(Keyboard/Mouse)/Barcode scanner support IEEE 802.11b/g/n/ac; WEP/WPA/WPA2 capable Near Field Communication (NFC) Functionality (Optional) The following NFC protocols are supported: ISO-14443-A ISO-14443-B Interfaces RS232 and USB2.0 interfaces by use of corresponding cables. USB 2.0 compliant interface configurable to support USB HID: Keyboard, or USB Virtual COM.
MIFARE Applications Read/Write of MIFARE Plus/Classic/Ultralight/DESFire cards Support MIFARE higher baud rate up to 424KHz Barcode Scanner Functionality 1D (Optional) Incorporates proximity detector to activate Bar Code Scanner. Outstanding scanning performance up to 270 scans per second. Below are the supported Bar Code types and settings. User Manual – i-series 2.0 UM600106 Rev.
User Manual – i-series 2.0 UM600106 Rev.
Barcode Scanner Functionality 2D (Optional) Incorporates proximity detector to activate the 2D Bar Code Scanner. For details, please visit the accessory product page at www.elotouch.com Magnetic Stripe Reader (MSR) Functionality (Optional) The MSR shall operate in keyboard mode. Capable of reading 3 tracks. Security level and Encryption function: OFF HDMI Output I-Series: I-Series is equipped with an HDMI port that can support secondary monitors with HDMI (1920x1080@60) input.
General Purpose Input/Output (GPIO) Support The i-Series supports a GPIO which can be used under the following conditions: Max Voltage: 5V Max Current: 200mA There are two input connections and one output connection. Pin 5 Volt output connection Pin 2 Input connection 1 Pin 3 Input connection 2 Pin 4 and Pin 5 are tied to ground Elo has a cable (PN # E086398) which extends this GPIO connection so that it is easy for users to connect their own peripherals. This cable can be found on the Elo website.
G-Sensor All i-series 2.0 units are equipped with an g-sensor and will rotate the video based on the orientation of the device. The simple drawing below illustrates the orientation when the device is rotated. User Manual – i-series 2.0 UM600106 Rev.
Consumer Electronic Control (CEC) The EloView Engine supports CEC functionality over the HDMI port. Note: CEC functionality is available for monitors that support CEC. Power Over Ethernet (PoE) The 10.1 and the 15.6in devices support the Elo peripheral for PoE. Refer to the PoE quick install guide for installation steps. Note: when the PoE is connected certain features are disabled in order to maximize available functions.
USB Control The i-series 2.0 provides control for each individual USB port. Any specific USB port can be turned off or on depending on the user. Intelligent Brightness Control To extend the life of the panel, Elo incorporates intelligent brightness control which disables the panels backlight during hours when the system is not being used. The function is fully controllable by the user. The default for this function is ON and will turn off the backlight during the hours of midnight and 6AM.
Section 3: Technical Support and Maintenance Solutions to Common Problems Problem Suggested Troubleshooting The Elo I-series 2.0 does not respond when turning on the system. Check that the power cable is properly connected to the wall. Power button LED will be red when system is properly connected to the wall. OR - Unplug the power cable, re-plug after five seconds, and press the power button to turn on the system.
Technical Assistance Technical Specifications Support visit www.elotouch.com/products visit www.elotouch.com/support for technical support for technical specifications for this device Refer to last page for worldwide technical support phone numbers. User Manual – i-series 2.0 UM600106 Rev.
Elo I-series 2.0 Care and Handling The following tips will help maintain optimal performance of your Elo I-series 2.0: Disconnect the power cable before cleaning. To clean the unit (except for touch screen), use a soft cotton or microfiber cloth lightly dampened with a mild detergent. It is important that your unit remains dry. Do not get liquids on or inside the unit. In the event that liquid does get inside, have a qualified service technician inspect the unit before you power it on again.
Section 4: Safety Waste Electrical & Electronic Equipment Directive (WEEE) This product should not be disposed of with household waste. It should be deposited at a facility that enables recovery and recycling. Elo has put in place recycling arrangements in certain parts of the world. For information on how you can access these arrangements, please visit www.elotouch.com/e-waste-recycling-program/. Caution: Risk of explosion if battery is replaced by an incorrect type.
Section 5: Regulatory Information Electrical Safety Information Compliance is required with respect to the voltage, frequency, and current requirements indicated on the manufacturer’s label. Connection to a different power source than those specified herein will likely result in improper operation, damage to the equipment or pose a fire hazard if the limitations are not followed. There are no operator serviceable parts inside this equipment.
indicated in European Standard EN 60950-1. General Information to all Users: This equipment generates, uses and can radiate radio frequency energy. If not installed and used according to this manual the equipment may cause interference with radio and television communications. There is, however, no guarantee that interference will not occur in any particular installation due to site-specific factors. 1. In order to meet emission and immunity requirements, the user must observe the following: a.
Radio Equipment Directive Elo hereby declares that the radio equipment type, i-series 2.0, is in compliance with Directive 2014/53/EU. The full text of the EU Declaration of Conformity is available at the following internet address: www.elotouch.com This device is designed and intended for indoor use only. Operation frequency and radio-frequency power are listed as below: o o WLAN 802.11b/g/n/a 2400 - 2483.5MHz < 17 dBm EIRP 5150 - 5250MHz < 18 dBm EIRP BT 2400-2483.
Changes or modifications not expressly approved by the party responsible for compliance could void the user‘s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Agency Certifications The following certifications and marks have been issued or declared for this peripheral: • FCC/IC • CE • UL/cUL/CB • Japan MIC • VCCI • China CCC • China SRRC User Manual – i-series 2.0 UM600106 Rev.
中国 RoHS (China RoHS) 根据中国法律《电器电子产品有害物质限制使用管理办法》，以下部分列出了产品 中可能包含的有害物质的名称和含量。 中国电子电气产品环境信息 有害物质 触控一体机 电缆组件 玻璃外罩 液晶面板 金属框架 塑胶盖 印制线路板 铅 (Pb) X X X X O X 汞 (Hg) O O O O O O 镉 (Cd) O O O O O O 六价铬 (Cr(VI)) O O O O O O 多溴联 苯 (PBB) O O O O O O 多溴二苯 醚 (PBDE) O O O O O O 本表格依据 SJ/T 11364 的规定编制. O: 表示该有害物质在该部件所有均质材料中的含量均在 GB/T 26572 规定 的限量要求以下. X: 表示该有害物质至少在该部件的某一均质材料中的含量超出 GB/T 26572 规定的限量要求. 标志说明 根据 SJ/T11364 的要求, 电子信息产品标有以下污染控制标识。 此产品在 10 年内不 会对环境产生影响。 User Manual – i-series 2.0 UM600106 Rev.
Power Specifications Electrical Ratings Input 120/240VAC Operating Conditions Temperature Humidity 0°C - 40°C 20% to 80% (non-condensing) Storage Conditions Temperature Humidity -20°C - 50°C 10% to 95% (non-condensing) User Manual – i-series 2.0 UM600106 Rev.
Section 6: Warranty Information For warranty information, go to http://support.elotouch.com/warranty/ User Manual – i-series 2.
www.elotouch.com Visit our website for the latest • Product Information • Specifications • Upcoming Events • Press Releases • Software Drivers To find out more about our extensive range of Elo touch solutions, go to www.elotouch.com, or call the office nearest you. North America Tel +1 408 597 8000 Fax +1 408 597 8001 elosales.na@elotouch.com User Manual – i-series 2.0 Europe Tel +32 (0)16 70 45 00 Fax +32 (0)16 70 45 49 elosales@elotouch.
