Hope Industrial Systems, Inc. User Manual 18” Panel Mount Industrial Monitor Model No.
TABLE OF CONTENTS Safety and Regulatory Information..............................3 Using the LCD Display ................................................4 Adjusting the Screen Image ........................................5 Main Menu Controls ....................................................6 Installation Instructions................................................9 Cleaning ....................................................................11 Troubleshooting ...........................................
Safety and Regulatory Information Warning To prevent fire or shock hazard, do not expose the unit to rain or moisture. Dangerously high voltages are present inside the unit. Do not disassemble the unit. Refer servicing to qualified personnel only. This equipment is not intended for use in critical applications where its failure to operate would create immediate life threatening circumstances.
Using the LCD Display Setting the Timing Mode Setting the timing mode is important for maximizing the quality of the screen image and minimizing eye strain. The timing mode consists of the resolution (example 1280 x 1024) and refresh rate (or vertical frequency; example 75 Hz). After setting the timing mode, use the controls to adjust the screen image. For the best picture quality set your LCD display timing mode to: VESA 1280 x 1024 @ 60Hz.
Adjusting the Screen Image Use the buttons on the rear control panel to display and adjust the On-Screen Display (OSD) controls which display on the screen. Do the following to adjust the screen image: 1 To display the Main Menu, press button [1]. NOTE: All OSD menus and adjustment screens disappear automatically after about 30 seconds. 2 3 To select a control you want to adjust, press ▲ or ▼ to scroll up or down the Main Menu. After the control is selected, press button [2].
Main Menu Controls Adjust the menu items shown below by using the up ▲ and down ▼ buttons. Control Explanation Auto Image Adjust automatically sizes, centers, and fine tunes the video signal to eliminate waviness and distortion. Press the [2] button to obtain a sharper image. NOTE: Auto Image Adjust works with most common video cards. If this function does not work on your LCD display, then lower the video refresh rate to 60 Hz and set the resolution to its pre-set value.
Manual Image Adjust displays the Manual Image Adjust menu. The Manual Image Adjust controls are explained below: Horizontal Size adjusts the width of the screen image. Horizontal Position moves the screen image left or right. Vertical Position moves the screen image up or down. Fine Tune sharpens focus by aligning the illuminated text and/or graphic charac- ters. Sharpness adjusts the clarity and focus of the screen image.
Language allows you to choose the language used in the menus and control screens. Resolution Notice displays the Resolution Notice menu shown below. Resolution Notice advises the optimal resolution to use. OSD Position allows you to move the on-screen display menus and control screens. OSD Timeout sets the length of time an on-screen display screen is displayed. For example, with a “15 second” setting, if a control is not pushed within 15 seconds, the display screen disappears.
Installation Instructions Preparing for Installation Important! Perform the following steps BEFORE Installation of the monitor into the panel. 1. Ensure that sufficient power is available. 2. Ensure that sufficient space is available to allow for proper airflow into and out of the unit. 3. Ensure that the air temperature around the unit (top and bottom) will not exceed the rated specifications of the unit.
Installation into Panel 1. Refer to the drawing below. 2. Locate position in panel for mounting of the monitor. Assure that there is adequate space begin the panel. Allow extra space (0.5 in. behind and on each side) for air ventilation. 3. Cut a rectangular hole in the panel. Clean and deburr. Dimensions: 17.85” (454mm) W x 14.44” (367mm) H ; +/- .020” 4. Separate the rear collar from the unit by removing the 12 nuts. 5. Insert the unit into the front of the panel and re-attach the collar. 6.
Touchscreen Driver Installation The enclosed CD-ROM contains documentation and drivers for all major operating systems. To assure you have the most current information, check the following Internet addresses: Manual - AccuTouch Product Manual - version 3.1a - (Part number 821615-000). http://elotouch.com/Support/dwnldmnls.asp Drivers – Specify the type of computer platform you will connect the touchscreen to and specify a serial connection. http://elotouch.com/Support/dnld.
Cleaning Resistive Touchscreen model Any standard glass cleaner can be used to clean the touchscreen. Always spray the glass cleaner on the cloth or towel and then clean the touchscreen. Glass cleaner sprayed directly on the monitor could possibly leak inside a non-sealed unit and cause damage. Vinegar or ammonia will not hurt the touchscreen. Again, spray the cloth and then clean the touchscreen.
Troubleshooting Blank Screen After installing the power adapter and connecting I/O cable to a PC, the monitor displays a blank screen. • Press the power button and check to see if the power LED is lit. • If the LED is not lit, make sure the PC is powered on. Make sure all cables are connected. • If the LED stays yellow, check to see if the PC is in the power saving mode by pressing any keys on the keyboard. Rolling Screen • • • • • Change PC display resolution to 1280x1024 at 60hz.
Drawings Front View 14
Bottom and Rear View (showing cutout dimensions) 15
Specifications Display Type Size Image size Native resolution Plug and Play Minimum resolution Pixel pitch Number of colors Viewing Angle (Hori/Vert) Brightness (white) Contrast ratio Back light Screen protector (when not shipped with touchscreen) Thin-film transistor (TFT) Active Matrix Liquid Crystal 18.0” diagonal 14.1” (359mm) x 11.3” (287mm) SXGA (1280 x 1024) @ 60 Hz DDC1/2B compatible VGA (640 x 350), operation in native resolution (1280 x 1024) will ensure best results 0.281mm (H) x 0.
Electrical Power Input Power consumption Power management Compliance 108 – 127 VAC, 60 Hz, 1A, or 216 – 254 VAC, 50 Hz, 0.5A Approximately 46 watts DPMS/energy star, < 3W UL 1950, cUL 959; FCC Class A Environmental Temperature Humidity Shock Vibration Altitude 0-45°C (consult factory for installation instructions when continuous 24/7 operation exceeds 40°C) 20% to 90% non-condensing 30g (1/2 sine, 11 msec.) 0.006 inch p-p 15-57Hz, 1.
Enclosure Type Panel mount; rear collar compresses gasket against panel, held by 12 10-32 studs NEMA 12/4/4X (with proper installation) – built to IP65 standards Panel rating Physical Depth Bezel Front bezel outside dimensions 1.9” (48 mm) behind panel maximum Acrylic - matte finish, black; or Stainless Steel 19.0” (483mm) W x 15.7” (399mm) H x 0.236” (6mm) thick (not including gasket) Cutout dimensions 17.60” (452mm) W x 14.40” (366mm) H ; +/- .020” Net weight 19 lbs. Shipping weight 25 lbs.
Warranty Statement Who is Covered? This warranty covers the purchaser of this product only and is not transferable without our written consent. What Does This Warranty Cover and What is the Period of Coverage? We warrant this product to be free from defects in material and workmanship, subject to the conditions set forth below. This warranty remains in force for a three-year period beginning on the date we invoice you for the product.
Publication UM-ML18B-1.0 August 2002 20 2002 Hope Industrial Systems, Inc.
