USER MANUAL Elo Touch Solutions ET0702L UM600315 Rev A
Copyright © 2019 Elo Touch Solutions, Inc. All Rights Reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, including, but not limited to, electronic, magnetic, optical, chemical, manual, or otherwise without prior written permission of Elo Touch Solutions, Inc. Disclaimer The information in this document is subject to change without notice. Elo Touch Solutions, Inc.
Table of Contents Section 1: Introduction ................................................................................................................................................................................................................................ 4 Section 2: Installation ...........................................................................................................................................................................................................................
Section 1: Introduction Product Description Your new touch monitor combines the latest developments in touch technology and display design with reliability for use in high-traffic environments. This touch monitor incorporates a 24-bit color, active matrix thin-film-transistor LCD panel to provide high-quality display performance. It’s resolution of 800x480 is suitable for displaying graphics and images.
Section 2: Installation Unpacking the Touch Monitor Open the carton and verify that the following items are present: • Touch monitor • Quick Install Guide • microUSB Type-B to USB Type-A Y-cable • Cable cover with screw User Manual ET702L 5
Connector Panel Touch Monitor Connections 1. Connect microUSB side of the USB Y-cable to monitor’s micro USB input connector and the other end of the Y-cable to USB type A ports on your computer. (It’s recommended that you plug in both USBs to your PC) 2. The touch monitor ships in an ON state, once the DisplayLink drivers are installed video should come up right away.
Installing the DisplayLink Video Drivers The DisplayLink technology enables video over USB, which will allow your monitor to use a single USB cable for power, video and touch. To download the latest DisplayLink drivers: 1. 2. 3. 4. Visit www.elotouch.com/Support/Downloads/Driver/DriverDownload/Default.aspx Select the Peripheral Drivers from the Product Category drop-down menu. Select the DisplayLink Video Driver from Select Product drop-down menu.
Section 3: Mounting Rear VESA Mount A four-hole 75 x 75 mm mounting interface for M4 screws is provided on the rear of the monitor.
Section 4: Operation Power To turn the touch monitor on or off, press the touch monitor’s power button once. The system consumes low power when in SLEEP or OFF modes. For detailed power-consumption specifications, refer to the technical specifications on the Elo website http://www.elotouch.com Touching the screen will bring the attached host PC out of SLEEP mode (similar to moving the mouse or pressing a keyboard key). Touch No calibration is required for projected capacitive touch technology.
Projected Capacitive Touch Technology When connected to Windows 7, 8 or 10 computers, the touch monitor can detect 10 simultaneous touches. When connected to Windows XP computers, the touch monitor detects only single touches. No additional drivers are required for this technology to work with Windows 7, 8 or 10, as it uses Windows HID drivers. Refer to Section 2, “Installing the Touch Technology Software Drivers,” for instructions on downloading touch drivers for Windows XP.
Gesture Support TouchPro PCAP technology enables several gestures that support single and multiple touches. Refer to the Microsoft website at http://msdn.microsoft.com/en-us/library/dd940543 on the various gestures that are supported in Windows 7, 8, 10 and later OS versions. Video A display’s native resolution is its width and height measured in pixels.
Section 5: Technical Support If you are experiencing trouble with your touch monitor, refer to the following suggestions. If the problem persists, please contact your local dealer or contact Elo Touch Solutions Customer Service. Worldwide technical support phone numbers are available on the last page of this user manual. Solutions to Common Problems Problem Suggested Troubleshooting The touch monitor does not respond when turning on the system. Check that the all the USB cables are plugged in correctly.
Technical Assistance Technical Specifications Technical Support Visit https://www.elotouch.com/products for technical specifications for this device Visit https://www.elotouch.com/support for technical support See this user manual’s last page for worldwide technical support phone numbers.
Section 6: Safety & Maintenance Safety • • • • To avoid risk of electric shock, follow all safety notices, and do not disassemble the touch monitor. The touch monitors are not user-serviceable. The touch monitor ships with a three-wire, grounded power cord. The power cord plug fits into grounded outlets only. Do not fit or modify the plug into an outlet that has not been configured for this purpose. Do not use a damaged power cord. Use only the power cord that came with your Elo touch monitor.
Section 7: Regulatory Information Electrical Safety Information Compliance is required with respect to the voltage, frequency, and current requirements indicated on the manufacturer’s label. Connection to a power source different than those specified herein will likely result in improper operation or damage to the equipment or pose a fire hazard. There are no user-serviceable parts inside this equipment. There are hazardous voltages generated by this equipment that constitute a safety hazard.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes: (1) l’appareil ne doit pas produire de brouillage; et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
User Manual ET0702L 17
Agency Certifications The following certifications and marks have been issued or declared for this monitor: • • • • • • • • Canada CUL, IC China CCC Europe CE United States FCC, UL Japan VCCI International CB Australia RCM Mexico NOM User Manual ET0702L 18
China RoHS In accordance with Chinese law (Administration on the Control of Pollution Caused by Electronic Information Products), the section below lists the names and amounts of the toxic and/or hazardous materials that this product may contain.
Explanation of Markings 1. In accordance with the SJ/T11364-2006 requirement, the electronic information products are marked with the following pollution control logo. The Environment-Friendly Use Period for this product is 10 years. The product will not leak or mutate under normal operating conditions, listed below, so that the use of this electronic information product will not result in any severe environmental pollution, any bodily injury, or damage to any assets.
Electrical Ratings Input 5 VDC, 1.
Section 8: Warranty Information Except as otherwise stated herein, or in an order acknowledgment delivered to Buyer, Seller warrants to Buyer that the Product shall be free of defects in materials and workmanship. The warranty for the touch monitors and their components is three years. Seller makes no warranty regarding the model life of components. Seller’s suppliers may at any time and from time to time make changes in the components delivered as Products or components.
Notes f User Manual ET0702L 23
Notes f User Manual ET0702L 24
www.elotouch.com Visit our website for the latest • Product Information • Specifications • Upcoming Events • Press Releases • Software Drivers • Touch Monitor Newsletter To find out more about our extensive range of Elo touch solutions, go to www.elotouch.com, or call the office nearest you. North America Tel +1 408 597 8000 Fax +1 408 597 8001 elosales.na@elotouch.com 670 N. McCarthy Blvd., Suite 100, Milpitas, CA 95035, USA.
