USER MANUAL Elo Touch Solutions ET1903LM, ET2203LM, ET2403LM, ET2703LM UM600152 Rev B
Copyright © 2018 Elo Touch Solutions, Inc. All Rights Reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, including, but not limited to, electronic, magnetic, optical, chemical, manual, or otherwise without prior written permission of Elo Touch Solutions, Inc. Disclaimer The information in this document is subject to change without notice. Elo Touch Solutions, Inc.
Table of Contents Section 1: Introduction ............................................................................................................................................................................................................................... 4 Section 2: Installation ............................................................................................................................................................................................................................
Section 1: Introduction Product Description Your new touch monitor combines the latest developments in touch technology and display design with reliability for use in high-traffic environments. This touch monitor incorporates a 24-bit color, active matrix thin-film-transistor LCD panel to provide high-quality display performance. The 03 Series includes full sizes from 19 to 27 inches and supports resolutions from 1280 x 1024 to full HD 1920 x 1080.
Section 2: Installation Unpacking the Touch Monitor Open the carton and verify that the following items are present: • Touch monitor with stand • Japanese-language regulatory information pamphlet • Quick Install Guide • VGA cable • HDMI cable • USB cable • Audio cable • Power brick • Europe power cord • North America power cord • 3 x tie wraps • EEI Label • 2 x cable cover screws User Manual ET1903LM, ET2203LM, ET2403LM, ET2703LM 5
Connector Panel Note: Cable tie-down points can be used to tie down the cables with tie wraps. Simply loop the tie wraps through the cable tie-down points and around the cable to secure cable connections. Touch Monitor Connections 1. Connect one end of the HDMI or VGA video cable to the monitor’s HDMI/VGA input connector and the other end to your HDMI/VGA video source. (Tighten the video cable’s screws on the VGA connector for best performance.) 2.
Installing the Touch Technology Software Drivers No additional drivers are required for your projected-capacitive touch monitor with Windows 7, 8 or 10 operating systems, as it will use the Windows HID drivers. If the monitor is used with the Windows XP operating system, follow the steps below to install the Windows XP touch driver. To download the latest touch drivers: 1. 2. 3. 4. Visit www.elotouch.com/Support/Downloads/Driver/DriverDownload/Default.
Section 3: Mounting Rear VESA Mount A four-hole 100 x 100 mm mounting interface for M4 screws is provided on the rear of the monitor. Remove the stand using a Phillips screwdriver to access the mounting interface. The VESA FDMI-compliant counting is coded VESA MIS-B, 75, C and VESA MIS-D, 100, C.
Base Mount The VESA FDMI-compliant counting is coded VESA MIS-E, C. ET1903LM & ET2203LM base mounting options are shown below.
ET2403LM & ET2703LM base mounting options shown below.
Magnetic Stripe Reader (MSR) Installation (Optional) Your monitor comes with four pheripheral ports, located at the top, bottom, left and right sides of the monitor. To mount an MSR, remove one of the pheripheral port covers with your finger tips and install the MSR as shown below. Please refer to the MSR Quick Install Guide (QIG) for set-up details.
Wall Mount Mount the wall bracket to the wall using six fasteners appropriate for the type of wall material and following all applicable building code standards. Ensure the unit is mounted to a solid structure and surface, such as a support beam or wall. Attach the other bracket to the monitor using the four M4 screws included in the kit. Hang the monitor on the wall bracket and secure using two M3 screws included with the kit on the left and right side of the bracket.
Handles Installation (Optional) Optional handles can be installed on 03 Series monitors, as shown below. Please note that it is not recommended to use handles to carry the touch monitor. Damage to the touch monitor will occur if the touch monitor is lifted by the handles. Use handles only to adjust the tilt angle.
Section 4: Operation Power To turn the touch monitor on or off, press the touch monitor’s power button once. The Power Status LED on the bottom of the touch monitor functions as follows: Touch Monitor Status LED Status OFF OFF SLEEP PULSING (Orange) ON ON ( Green) The system consumes low power when in SLEEP or OFF modes. For detailed power-consumption specifications, refer to the technical specifications on the Elo website http://www.elotouch.
Projected Capacitive Touch Technology When connected to Windows 7, 8 or 10 computers, the touch monitor can detect 10 simultaneous touches. When connected to Windows XP computers, the touch monitor detects only single touches. No additional drivers are required for this technology to work with Windows 7, 8 or 10, as it uses Windows HID drivers. Refer to Section 2, “Installing the Touch Technology Software Drivers,” for instructions on downloading touch drivers for Windows XP.
Gesture Support TouchPro PCAP technology enables several gestures that support single and multiple touches. Refer to the Microsoft website at http://msdn.microsoft.com/en-us/library/dd940543 on the various gestures that are supported in Windows 7, 8, 10 and later OS versions. Video A display’s native resolution is its width and height measured in pixels.
The OSD buttons control an on-screen graphical user interface that overlays your input video, allowing the following adjustments: Parameter Available Adjustment Brightness Increases/decreases monitor brightness. Default: maximum Contrast Increases/decreases monitor contrast. Default: best gray-shade performance Clock Allows fine adjustments of the panel’s pixel dot clock. Applicable for VGA input video only. Phase Allows fine adjustments of the panel’s pixel dot clock phase.
Parameter Available Adjustment OSD H-Position Adjusts the horizontal location of the OSD menus on the display. Default: centered OSD V-Position Adjusts the vertical location of the OSD menus on the display. Default: centered OSD Timeout Adjusts how long the touch monitor will wait without OSD button activity before closing the OSD. The adjustable range is between 5 and 60 seconds. Default: 15 seconds OSD Language Selects the OSD’s display language.
OSD and Power Lockouts Press and hold the “Menu” and “ ” buttons simultaneously for two seconds to enable/disable the OSD Locking feature. When OSD Locking is enabled, pressing any of the Menu, Up, Down or Select keys will have no effect. Press and hold the “Menu” and “ ” buttons simultaneously for two seconds to enable/disable the Power Locking feature. When Power Locking is enabled, pressing the power switch will have no effect.
Section 5: Technical Support If you are experiencing trouble with your touch monitor, refer to the following suggestions. If the problem persists, please contact your local dealer or contact Elo Touch Solutions Customer Service. Worldwide technical support phone numbers are available on the last page of this user manual. Solutions to Common Problems Problem Suggested Troubleshooting The touch monitor does not respond when turning on the system. Check that the DC power adaptor is properly connected.
Technical Assistance Technical Specifications Technical Support visit www.elotouch.com/products for technical specifications for this device Visit https://www.elotouch.com/support for technical support See this user manual’s last page for worldwide technical support phone numbers.
Section 6: Safety & Maintenance Safety • • • • To avoid risk of electric shock, follow all safety notices, and do not disassemble the touch monitor. The touch monitors are not user-serviceable. The touch monitor ships with a three-wire, grounded power cord. The power cord plug fits into grounded outlets only. Do not fit or modify the plug into an outlet that has not been configured for this purpose. Do not use a damaged power cord. Use only the power cord that came with your Elo touch monitor.
Section 7: Regulatory Information Electrical Safety Information Compliance is required with respect to the voltage, frequency, and current requirements indicated on the manufacturer’s label. Connection to a power source different than those specified herein will likely result in improper operation or damage to the equipment, or pose a fire hazard. There are no user-serviceable parts inside this equipment. There are hazardous voltages generated by this equipment that constitute a safety hazard.
conditions suivantes : (1) l’appareil ne doit pas produire de brouillage; et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. Notice to Users in the European Union: Use only the provided power cords and interconnecting cabling provided with the equipment.
Agency Certifications The following certifications and marks have been issued or declared for this monitor: • • • • • • • • • • • Canada CUL, IC China CCC Europe CE Korea KCC Taiwan BSMI United States FCC, UL Japan VCC! International CB Australia RCM Russia EAC Mexico CoC User Manual ET1903LM, ET2203LM, ET2403LM, ET2703LM 20
Safety Standards For ET1903LM, ET2203LM, ET2403LM, ET2703LM ET1903LM, ET2203LM, ET2403LM, ET2703LM touch monitors have been tested and certified for compliance with the following medical electrical equipmentgeneral requirements for basic safety and essential performance standards: • AAMI/ANSI ES60601-1:2005/(R)2012 and A1:2012, C1:2009/(R)2012 and A2:2010/(R)2012/IEC60601-1:2005+A1 (CE) • AAMI/ANSI ES60601-1:2005/(R)2012 and A1:2012, C1:2009/(R)2012 and A2:2010/(R)2012 (UL) • CSA C22.2 No.
Safety Signs and Symbols Description This symbol alerts the user that important literature concerning the operation and maintenance of this unit has been included. Therefore, it should be read carefully to avoid any problems. Protective earth terminal marked. Stand by. AC Input. Accessory equipment connected to the analog and digital interfaces must comply with the respective nationally harmonized IEC standards (i.e.
China RoHS In accordance with Chinese law (Administration on the Control of Pollution Caused by Electronic Information Products), the section below lists the names and amounts of the toxic and/or hazardous materials that this product may contain.
Explanation of Markings 1. In accordance with the SJ/T11364-2006 requirement, the electronic information products are marked with the following pollution control logo. The Environment-Friendly Use Period for this product is 10 years. The product will not leak or mutate under normal operating conditions, listed below, so that the use of this electronic information product will not result in any severe environmental pollution, any bodily injury, or damage to any assets.
Monitor Specifications Electrical Ratings Input 12 VDC, 4.0 A Operating Conditions Temperature 0-40°C Humidity 20-80% (non-condensing) Altitude 0-3,048 m Storage Conditions Temperature -20-60°C Humidity 10-95% (non-condensing) Altitude 0-12,192 m Ingress Protection IP Rating IP54 - Under the following condition: Use the rear VESA mount stand and keep all connector and peripheral covers tightly sealed. Power Brick doesn’t comply with IP54 rating.
Section 8: Warranty Information Except as otherwise stated herein, or in an order acknowledgment delivered to Buyer, Seller warrants to Buyer that the Product shall be free of defects in materials and workmanship. The warranty for the touch monitors and their components is three years. Seller makes no warranty regarding the model life of components. Seller’s suppliers may at any time and from time to time make changes in the components delivered as Products or components.
ELO LCD Touch Monitor Intended User Profile (IEC) Age preference 50-70 (1st priority) (Intended User Profile 1) User is also a Patient: Education: - vocational high school graduate - major in electrical or electronic field of study - no maximum Knowledge: – minimum: – understanding the definition of voltage, current and frequency – understanding the definition of Class I (basic insulation) and Class II (double insulation) – could recognize the symbols of alternating current (AC), direct current (DC), protec
Notes f User Manual ET1903LM, ET2203LM, ET2403LM, ET2703LM 28
Notes f User Manual ET1903LM, ET2203LM, ET2403LM, ET2703LM 29
www.elotouch.com Visit our website for the latest • Product Information • Specifications • Upcoming Events • Press Releases • Software Drivers • Touch Monitor Newsletter To find out more about our extensive range of Elo touch solutions, go to www.elotouch.com, or call the office nearest you. North America Tel +1 408 597 8000 Fax +1 408 597 8001 elosales.na@elotouch.com 670 N. McCarthy Blvd., Suite 100, Milpitas, CA 95035, USA.