Quick Start Guide ELPRO 105U-L-T Wireless I/O Transmitter Unit man_105U-L-T_QuickStart_v1-8.
ELPRO 105U-L-T Wireless I/O Transmitter Unit Quick Start Guide About this document This document is the ELPRO 105U-L-T Wireless I/O Transmitter Unit Quick Start Guide and contains the following sections: Section Read this section if you want to … Basic steps for using your unit Learn the basic steps for installing and using your unit. Factory default configuration Understand how the transmitter sends information to the receiver. Unit components Understand the different parts of your unit.
ELPRO 105U-L-T Wireless I/O Transmitter Unit Quick Start Guide Unit components and connections Your 105U-L transmitter unit has the following components and terminal connections: Earth Wire Lug underneath Unit **IMPORTANT ELECTRICAL SAFETY INFORMATION** In order to comply with Electrical Safety Regulations, this module must be installed in an Electrical AND Fire enclosure. This enclosure may be a single or multiple enclosures. Access to the module is to be made by a Service Person only.
ELPRO 105U-L-T Wireless I/O Transmitter Unit Quick Start Guide The front panel contains the following components: The triangle on the rotary switch indicates the current position, for example: Position 0 Position 1 NOTE: To avoid damaging the rotary switch, use a screwdriver to change the position. The rotary switch uses the following setpoint levels: Position Lower level (mA) Upper level (mA) 1 4.8 6.4 2 6.4 8.0 3 8.0 9.6 4 9.6 11.2 5 11.2 12.8 6 12.8 14.4 7 14.4 16.0 8 16.
ELPRO 105U-L-T Wireless I/O Transmitter Unit Quick Start Guide The LEDs on the front panel indicate the unit status: LED Status Indicates None No power supply. OK LED Green Current status of the unit OK. OK LED Red Fault condition detected in unit. TX Led Flashes Transmitting Message. PG LED on Configuration Cable Connected. Input LED ON Input LEDS (i.e. D1,D2, SP, AZ.) light when the corresponding input is active. All LEDs medium flash D1 Digital Input 1 is active (Low).
ELPRO 105U-L-T Wireless I/O Transmitter Unit Quick Start Guide Resetting your unit to factory defaults To reset the default factory configuration: 1. Set the RSSI rotary switch to position 0 using a screwdriver. 2. Power on the 105U-L transmitter. 3. The 105U-L transmitter flashes all LEDs at medium flash (i.e. 1.6 Hz). NOTE: If the LEDs do not flash, you must repeat steps 1 and 2 until the LEDs flash before continuing. 4. Set the RSSI rotary switch to another position (i.e. position 1) within 5 seconds.
ELPRO 105U-L-T Wireless I/O Transmitter Unit Quick Start Guide Safety information Thank you for selecting the 105U-L transmitter for your telemetry needs. We trust it will give you many years of valuable service. To ensure your 105U-L transmitter enjoys a long life, double-check ALL your connections with the user’s manual before powering on the unit. WARNING: Incorrect termination of supply wires may cause internal damage and will void warranty.
ELPRO 105U-L-T Wireless I/O Transmitter Unit Quick Start Guide Document information Quick Start Guide ELPRO 105U-L-T Wireless I/O Transmitter Unit Version 1.8 ELPRO contact details Address > 9 /12 Billabong Street Stafford, QLD 4053 Telephone > + 61 (0)7 3352 4533 Fax > + 61 (0)7 3352 4577 Email > sales@elprotech.com Website > www.elprotech.com Copyright Copyright © 2006 ELPRO Technologies Pty Ltd. All rights reserved.