User's Manual Part 1
Table Of Contents
- TABLE OF CONTENTS
- CHAPTER 1 GENERAL DESCRIPTION
- CHAPTER 2 INSTALLATION AND OPERATION
- 2.1 INSTALLATION 2-2
- 2.2 OPERATION 2-6
- 2.2.1 Controls and Indicators 2-6
- 2.2.2 LCD Messages Related to Printer Module 2-7
- 2.2.3 LCD Messages Related to Laminator Module 2-7
- 2.2.4 LCD Messages Related to Encoder Module 2-8
- 2.2.5 LCD Messages Related to Adjustments, Testing, and Microcode Downloads 2-8
- 2.2.6 LCD Messages Related to Cleaning 2-8
- 2.2.7 Print Head Latch and Release Levers 2-9
- 2.2.8 Ribbon Installation 2-10
- 2.2.9 Card Media 2-11
- 2.2.10 Clear Card Material Loads 2-11
- 2.2.11 White Card Feeder Loading 2-12
- 2.2.12 Two- verses Three-Layer Selection 2-13
- CHAPTER 3 THEORY OF OPERATION
- CHAPTER 4 TROUBLESHOOTING
- CHAPTER 5 REPLACEMENT PROCEDURES
- TABLE OF FIGURES
- Figure 2-8. Clear Card Material Loads. 2-11
- Figure 2-9. White Card Hopper Loading. 2-12
- Figure 2-10. Card Layer Selection Lever. 2-13
- Figure 3-1. 3M MAXSecure Card Path. 3-7
- Figure 3-2. Block Diagram. 3-9
- Figure 4-1. Problems Duplicated by a Test Print. 4-2
- Figure 4-2. Interface Diagnostic Flow. 4-5
FOREWORD
This manual contains service and repair information for 3M MAXSecure Printer Modules manufactured by the
3M Corporation,St. Paul, Minnesota. The contents include maintenance, diagnosis and repair information.
TECHNICAL SUPPORT
For technical support, users should first contact the distributor that originally sold the product—phone +1 (800)
344 4003 to locate the nearest 3M Distributor.
COPYRIGHT NOTICE
This document contains information proprietary to 3M Corporation. This document and the information
contained within is copyright by 3M Corporation and may not be duplicated in full or in part by any person
without prior written approval of 3M..
While every effort has been made to keep the information contained within current and accurate as of the date of
publication, no guarantee is given or implied that the document is error-free or that it is accurate with regard to
any specification.
This information is not intended as a license to practice or infringe on the patents of this company or others. 3M
Corporation reserves the right to modify, update or revise this information at any time without notice.
TRADEMARKS
3M MAXSecure is a service mark, and 3M is a registered trademark of 3M Corporation. All other marks are
trademarks or registered trademarks of their respective holders.
FCC NOTICE:
This equipment has been tested and found to comply with the limits of a Class A digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. Operation of this equipment in a residential area is likely to cause harmful interference in
which case the user will be required to correct the interference at their own expense.
CSA NOTICE:
This equipment does not exceed Class A limits per radio noise emissions for digital apparatus set out in the Radio
Interference Regulation of the Canadian Department of Communications. Operation in a residential area may
cause unacceptable interference to radio and TV reception requiring the owner or operator to take whatever
steps are necessary to correct the interference.
Ce matériel ne dépasse pas les limites de Classe A d’émission de bruits radioélectriques pour les appareils
numériques telles qu’établies par le ministère des Communications du Canada. L’exploitation faite en milieu
résidentiel peut entraîner le brouillage des réceptions radio et télé, ce qui obligerait le propriétaire ou l’opérateur
à prendre les dispositions nécessaires pour en éliminer les causes.
i