OWNER’S MANUAL EQ.45 Specifications Main Rotor Blade Length: 315mm Tail Rotor Blade Length: 55 mm Overall Length: 630mm Width: 120 mm Height: 230 mm Weight: 620g Battery: Lipo 11.1V 1200/1800 mAh Model Features Aluminum Rotor Head 120° CCPM Control System Brushless ESC (12V 35A) High Performance Brushless ESC High Performance Brushless Motor Hi Performance Auto-Rotation System Hi Performance Head Lock Gyro Servo Tail 2.
Index Introduction Warning Warranty Information Battery Warnings, Guidelines and Charging Safety precautions Kit Contents Charging the batteries Assembly Instructions Install Batteries in the Transmitter Install the Transmitter Antenna Install the Battery Install Main Rotor Blades Blade Tension Test Assemble Training Gear Get the model Ready-To-Fly (RTF) Electric Motor warning Turning the Model On Range Check Balance the Main Blades General Radio Control Transmitter Transmitter Controls Control Functions Tr
Introduction Congratulation for your choice! The EQ.45 R/C helicopter is a high performance Ready-to-Fly Electric Helicopter for indoor and outdoor flying on calm days. At about 620 grams, the EQ.45 R/C helicopter will fly for 5-8 minutes powered by 11.1V 1200mAh LiPo batteries. Although the R/C helicopter EQ.45 is not difficult to operate, we recommend you to carefully read these instructions, for a proper and safe use of it. Warning The EQ.
By handling, charging or using the included Li-Po battery you assume all risks associated with lithium batteries. If you do not agree with these conditions, return your complete EQ.45 model in new, unused condition to the place of purchase immediately. You must charge the included 11.1V 100mAh 3-cell Li-Po battery pack in a safe area away from flammable materials. 9 9 9 9 9 9 9 9 9 Do not charge the battery when installed in the helicopter. Never charge the battery unattended.
Kit Contents Before starting assembly, take an inventory of the EQ.45 RTF to make sure it is complete, and inspect the parts to make sure they are of acceptable quality. If any parts are missing or are not of acceptable quality, or if you need assistance with assembly, contact Product Support. If any defective or missing parts, please use the part names exactly as they are written in the Kit Contents list. 1. Trasmitter 2. Main Rotor Blades 3. Canopy 4. Helicopter 5. Battery Charger 6.
Install the Transmitter Antenna Insert the antenna into the top of the transmitter and turn clockwise until tight. Install the Battery Remove the canopy by sliding the canopy grommets off of the rods. Slide the battery into the front of the battery tray as shown above. Use a rubber band to hold the battery into the tray. Install Main Rotor Blades Using the 3 x 12mm hex screws, and M3 nut. Mount the main rotor blades as shown. Be careful not to over-tighten them.
step for the other three balls. Get the model Ready-To-Fly (RTF) Electric Motor warning Electric motors are very dangerous. Please remove the pinion gear or unplug the motor while working on the model. Turning the Model On Always turn the Transmitter on first. Then, with the EQ.45 sitting still, plug the battery into the ESC. The EQ.45 will need to sit still for 10 seconds so the gyro can initialize and determine centre. If the EQ.
Transmitter Always turn the Transmitter on first and then with the EQ.45 sitting still plug the battery into the ESC. The helicopter will need to sit still for 10 seconds so the gyro can initialize and can determine centre. If the EQ.45 is moved during this initialization, then the gyro will not operate properly. There is a safety built into the EQ.45 that prevents the motor from activating unless the collective stick has been lowered to its lowest position.
Transmitter back and side view In the back side of the transmitter, there are the following plugs: 1. Serial Comm Port: plug the communication cable in order to configure the transmitter. 2. Charger Port: use to charge the transmitter batteries. ElyQ doesn’t provide any battery charger and recommends to unplug the batteries and than charge externally. 3. Battery placeholder Receiver and Servo connectivity The radio supports six channels.
Transmitter Boot 1. 2. 3. Switch the radio on. Turn on the helicopter connecting the battery plug. The receiver led should light on. Now it is possible to fly. Transmitter Shutdown 1. 2. Cut off the receiver power supply (by unplugging the battery cord). Switch off the radio transmitter. Transmitter configuration software Before installing the transmitter configuration software (T6Config.exe), it is necessary to setup the PL-2303 USB to serial adapter driver.
In the interface window can be detected four different areas, corresponding to groups of functions supported by the radio: 9 Channels: for each channel the black bar represents the servo command position. 9 System Option 9 System Setting 9 Switch Program T6Config: System Option The functions supported in this section are the following: ¾ GetUser: import the transmitter data to PC. Before changing any of the transmitter parameters (and at first use), please execute the GetUser function.
¾ DR (Dual rate): defines the gain percentage gain of the corresponding control (default value is 70) .This function can be applied to CH1, CH2 and CH4 channels only and it is enabled by setting the corresponding switch. ¾ Thro Cuv: represents the engine throttle curve, and can be used to improve the performance of the model. Please select NOR for normal flight mode. Please select ID for acrobatic flight mode. The curves are divided in 5 segments, which can be configured with values between 0% and 100%.
T6Config: Switch Program The functions supported in this section are the following: ¾ Switch A / Switch B: each switch can be programmed individually. It is possible to select 1 between DR (Dual Rate), THRO CUT (throttle cut) and NOR / ID (normal or idle). ¾ VR (A) / VR (B): choose on of these potentiometers in order to adjust the pitch (by selecting PITH ADJUST). The other, can be used for channel mixing.
Roll Trim Adjustment – Mode 1 If the helicopter does not fly in neutral position, adjust the Trims. The Trim adjustment depends on the helicopter action. Please look at the pictures below in order to understand how to trim perfectly your helicopter. Elevator / Pitch Trim – Stick Input / Heli Action Tail Rotor / Yaw Trim - Stick Input / Heli Action Aleiron Trim - Stick Input / Heli Action Transmitter Operation and Control – Mode 2 Elevator Tail User’s manual r.0805 EQ45 (EN) www.elyq.
Pitch Roll Trim Adjustment – Mode 2 Elevator / Pitch Trim – Stick Input / Heli Action Tail Rotor / Yaw Trim – Stick Input / Heli Action Aleiron Trim – Stick Input / Heli Action User’s manual r.0805 EQ45 (EN) www.elyq.
Tracking the main Blades At zero pitch, bring the main rotor up to speed and observe whether the rotational planes of the blades are the same. If they are not, adjust one of the linkages to bring the blades into the same plane. Apply the two different colored stripe decals to the tips of your main rotor blades. The training gear is a big help to beginners. They soften not so perfect landings and help to prevent the helicopter from tipping over.
Aerobatics So you are getting pretty comfortable in fast forward flight. Well, now it's time to slowly progress into aerobatics. Once you are into forward flight start using the idle up switch which raises the rotor RPM for aerobatics and gives us the ability to fly inverted. In wind it may be difficult to descend to land without the idle up on. Your first step is chandelles. Fly straight across in front of you and pull up to a 45" angle.
Spare Parts Q4501 Chassis set Q4502 Landing skid structure set Q4503 Ball link set Q4504 Ball link set B Q4505 Main gear set Q4506 Tail drive gear assembly Q4507 Tail servo mount set Q4508 Belt set Q4509 Stabilizer set yellow Q4510 Tail rotor blade set yellow Q4511 Landing gear stopper yellow Q4512 Landing gear end cap yellow Q4513 Main frame set Q4514 Stabilizer/fin set Q4515 Canopy set Q4516 Blade holder Q4517 Landing gear skids Q4518 Main shaft set Q4519 Spindle shaft Q4520 Main shaft
Q4525 Tail support PVC set Q4526 Brass balls w/screws Q4527 Brass balls w/screws Q4528 Autorotation sleeve set Q4529 Tail boom support set Q4530 Pitch lever joint set Q4531 Main frame holder set (4.5*2.5mm) Q4532 Main frame holder set Q4533 L arm support holder Q4534 Tail boom Q4535 Belt wheel set Q4536 Linkage set Q4537 Main rotor blade set Q4538 Screw set for main frame set (m1.
Q4549 Aluminium l arms set Q4550 Swashplate antirotation CNC Q4551 Aluminium swashplate set Q4552 Stabilizer bar adaptor set Q4553 Aluminium tail boom mount Q4554 Aluminium tail case set Q4555 Aluminium tail pitch lever Q4556 Aluminium tail pitch yoke Q4557 Aluminium tail grip set Q4558 Aluminium bearing block (main shaft) Q4559 Motor gear set (11t) Q4560 Washer set (d2, d4, w0,4) 50 pcs Q4561 O-ring set Q4562 Carbon main rotor blades set (carbon fiber) Q4563 Carbon main rotor blades set (fibe
Q4573 Ball bearing 2*5*2.5mm 4 pcs Q4574 Ball bearing 3*6*2mm - 2 pcs Q4575 Ball bearing 5*10*4mm 2 pcs Q4576 Ball bearing 5*8*2.5mm2 pcs Q4577 Ball bearing 3*8*4mm - 4 pcs Q4578 Ball bearing 3*6*2.5mm 2 pcs Q4579 Ball bearing 20*25*4mm 1 pc Q4580 Ball bearing 3*8*3mm - 4 pcs Q4581 One-way bearing 8*12*12mm - 1pc Q4582 Brushless motor Q4583 Esc (12v 30a) Q4584 Battery (11.1v 1200 mah) Q4585 Battery(11.1v 1800 mah) Q4586 Charger Q4587 Gyro Q4588 Servo Q4589 Transmitter (6ch/2.
